1994 CADILLAC FLEETWOOD display

ELECTRONIC CLIMTE CONTROL
With this system you can control the ventilation, heating and air
conditioning in your vehicle automatically by setting the desired
temperature. The digital screen displays the outside temperature, the
I
inside temperature setting, fan speed, and the ECC selection you have
selected.
OUT TEMP (Outside Temperature)
Push this to get the outside temperature. Push it again to return to the
regular system display.
TEMP (Inside Temperature)
Sets the interior temperature you want. Press the lower portion (blue
arrow) to lower the inside temperature setting. Press the upper portion
(red arrow) to raise the temperature setting. Once you set the
temperature, the system will automatically maintain the set temperature.
You can change the temperature from 65 F (18 C) to 85 F (29 " C), one
degree at a time. You may also choose
60 " F (16 " C), for maximum
cooling, and 90°F
(33 "C), for maximum heating, the fan will stay on high
speed unless you select a different speed.
In maximum heating most of
the air will
flow out the heater ducts. In maximum cooling, the system will
recirculate the air inside your vehicle instead of pulling air from outside.
147

I
OFF
Nothing is on, but air will flow through your Cadillac if the the car is
moving. The air flow will be felt through the heater ducts.
ECON
Use this in cold or cool weather to save fuel. It won’t cool or remove
humidity from the air. However, the system will try to keep the air at the
chosen temperature.
If it’s so warm outside that you need to cool the air, use the next choice.
I AUTO
With this setting the system automatically controls the temperature, air
distribution and fan speeds. In cold conditions the the fan well not come
on until the system senses that the engine has started to warm up. This
prevents cold air from blowing on you and your occupants.
I
I FAN
The fan speed is controlled automatically if you have the Electronic
Climate Control set
on “AUTO.” However, if you want the fan to run at a
lower speed, push the lower portion of the fan switch.
If you want the blower to run at a fixed higher speed, push the upper
portion of the fan switch until you see
“HI” on the display.
If you want the fan to run at a fixed low speed, push the switch until “LO”
is shown on the display.
If you want the fan speed to be automatic but you like the fan to be
higher or lower than the
“AUTO” settings, just push the switch until
either
“HI AUTO” or “AUTO LO” is displayed.
If the Fahrenheit (F’) or Celsius (C”) symbol begins to flash, or flashes
when you turn
on the ignition, it indicates an electrical problem with your
148
G
I
1
q: LI

Please read the following to operate the radio portion of your Delco
radio system.
The upper knob
The upper knob does these four things:
0
0
0
0
0
It turns the radio on and off.
It controls the volume.
Volume level automatically adjusts to compensate for road and wind
noise as you're driving your Cadillac. Adjust the volume to the
listening level you want at any time. Then as you drive the volume will
change to match the noise present at any particular speed. The
volume should always sound close to the same level to you as
you
drive.
It lets you see what station you have. (When the radio is on, push the
knob to display the station.)
It tells you the time. (When the ignition is
off, push the upper knob to
display the time.)
Behind the upper knob is a balance control. It moves the sound between
the left and right speakers.
154
n
r
Ll
I s
UI
D'
i
-
d

The lower knob
Turn the lower knob to choose radio stations. Push the knob to switch
from
AM to FM.
The control behind the lower knob moves the sound between your front
and rear speakers.
SCAN
When you push this switch either up or down, the SCAN indicator in the
display will light and the radio will find the next station and stay there for
5 to 10 seconds. Then it will go to the next station and pause, and keep
doing that. When you want it to stop, just push either the
SCAN switch
again or the upper knob.
SEEK
This switch chooses stations, but it doesn’t keep moving as SCAN does.
When you push
SEEK up or down, the radio will automatically go to the
next strongest station and stay there.
WSH BUTTONS
You can set the push
buttons to get up to
ten favorite stations
(Five on
AM and five
on
FM.) Just:
Choose either AM or FM.
0 Tune in the station.
155

I Push the SET button.
Within
.5 seconds, push one of the five push buttons.
Repeat these steps for each of the five push buttons.
PRESET EQUALrZATION
The Preset Equalization buttons let you adjust the tone, to sound just the
way you want it. Each individual auto-equalization button (A through E)
contains a separate equalization adjustment feature.
When your vehicle
is new, the auto-equalization is already preset with
Preset A having more bass and treble tone than mid-range tone. Preset
B
has more bass than treble and mid-range tone. Preset C has an overall flat
response in sound. Preset
D has more treble than bass and mid-range,
and Preset
E has more mid-range sound than bass and treble. These
preset settings can be modified individually for
AM, FM, cassette or
CD play.
Follow these steps to modify each
of the Preset Auto-equalization
buttons.
. ,\%:. .. . . ,! - ;, .: ,,; !:;;? ;.y=K&> .I.‘!.;,*’ .:. ~ -4 6°K; -..L,.l __ .. , s+.qb+‘’ ,:Li;%j :&;% ,:
First, seTect’one oft e Preset Equ
, . .. 9- : , -;.;I< f?,;., ;,x 7 ..f& * -q$; ;’{ :!&i”Y,.
2. Equalization Band
3. Equalization Gain (1 thru 15) I
- i’ &:i ,; -4% @ -. 1.. - --.. ,tu:. J
0 Press the SET button’, and then press and hold the Preset Equalization I
I
button you have selected, until either an “F” or “U” is displayed
(about
10 seconds).

The display will show either 3 or 4 digits and the preset button “LED”
will flash. In the farthest right position of the display will be an “F”
(for factory setting), or if the equalization has been modified, a “U”
(for user setting).
Press the SCAN switch up or down to select the band you prefer.
The middle digit indicates the equalization band. There are five bands
60Hz, 250Hz, lkHz, 3.5Hz and lOkHz, numbered
1 through 5
respectively. The band will display band 1 when the mode is first entered.
Press the SEEK switch up or down to select the gain setting you want.
The left digit, or
two digits are the equalization gain settings (0-15) for
each band. The display
will indicate the active setting (F or U) when
the mode is first entered.
A typical setting for a flat response is 7.
0 Press the upper radio knob to compare the factory setting to your
setting. Once you are satisfied with your selection, press and hold the
preset equalization button for about
4 seconds, the“ Pr” (program)
will display indicating that your selection is programmed.
If you have programmed the preset equalization buttons and set the push
buttons to the stations you’ve selected, you can preset the five Preset
Equalization buttons to a particular station. Just:
Tune in a station using one of the preset push buttons.
157

To Play A Cassette Tape I.
0 Turn the radio on.
0 Insert the cassette squarely through the tape door. (The TP indicator
If you hear nothing or hear just a garbled sound, the cassette may not be
in squarely. Push the EJECT button to remove the tape and start over.
The tape equalization is automatically sensed and set. Inserting the
cassette also automatically disables DNR@* and activates DOLBY@
noise reduction.
DNR@ is the Dynamic Noise Reduction. It helps remove background hiss
noise from the radio.
Once the tape is playing, use the upper and lower knobs to adjust the
volume and balance, just
as you do for the radio. Push the upper knob
to change tape direction. The arrows show which direction the tape is
being played.
in
the display will light.)
To go forward rapidly to another part of the tape push FWD. To go
backward, push
REV To stop the tape, push the same button lightly or any
of the other buttons. The radio will play during fast forward or reverse.
*DNR@ is a registered trademark
of National Semiconductor
Corporation.
159

To Play the Disc Player
Before you begin, please note: don’t use the mini-discs that are called
“singles”. They won’t eject. Use full-size compact discs only.
Turn the radio on.
Insert a disc (label side up) partway into the slot. The player will pull it in.
Wait a few seconds and the disc will play.
The DNR@ will be disabled and
the display will show Track
“1 TRK CD” for about 5 seconds, then “CD”
will show in the display.
If the disc comes back out, check to see if
0 The disc is upside down.
0 The disc is dirty, scratched, or wet.
0 There’s too much moisture in the air. (If there is, wait about one hour
and try again).
RCL JPROG (RecallJProgram)
Press once to see which track is being played. (It also allows for disc
programming.)
Within 5 seconds press it a second time to see how long the disc has
been playing.
0 Press it a third time to see the time of day.
To Program Packs
You can program up to 10 tracks for your listening pleasure.
1. Press the RCL/PROG knob. “CD” and “TRACK” will light in the
2. Within 5 seconds, turn the lower TUNE knob to the track you want to
3. Press the SET button and the track number will stop flashing. This
display.
This also allows you to program disc track playback.
hear first. The track number will flash.
indicates that the track is programmed.
4. Repeat steps 2 and 3 to program up to 9 more tracks.
161