1994 BUICK CENTURY ignition

2. Within 5 seconds, press and hold SCAN until the
correct hour appears
on the display.
3. Press and hold SEEK until the correct minute
appears on the display.
...... _.__” ....... ~ ........ .”... .. 7
To Play This Radio
Power
Press PWR to turn the unit on and off when the ignition
is on.
Upper Knob
The upper knob does these things:
0 Rotate VOL to control the volume.
When the ignition is off, press the knob to display
the time.
When a tape is playing, press the knob t.o hear the
other side of the tape.
Balance
The BAL control behind the upper knob adjusts the
left/right speaker balance.
Lower Knob
This knob does two things:
Rotate it to tune in radio stations.
Press it to change between the AM and FM bands.
Fade
The FADE control behind the lower knob adjusts the
front/rear speaker balance.
Treble
Slide this lever up to increase treble, or down to
decrease
it. If a station is weak or noisy, reduce the
treble.
128
ProCarManuals.com

To Play a Cassette Tape
With the power switch on, insert a tape into the cassette
door. Using tapes that are longer than
90 minutes
(45 minutes on each side) is not recommended.
When the right indicator arrow is lit, selections listed on
the bottom side of the cassette are playing. When the left
arrow is lit, selections listed on the top side of the
cassette are playing. To change sides of the tape, press
the upper control
knob (VOL ) while the cassette is
playing. The tape player automatically begins playing
the other side when it reaches the end
of the tape.
Fast Forward
To rapidly advance the tape, press the button with the
arrow pointing in the same direction the tape is playing.
To stop fast forward, lightly press the STOP-EJECT
button.
Reverse
To rapidly reverse the tape, press the button with the
arrow pointing in the opposite direction the tape
is
playing. To stop reverse, lightly press the STOP-EJECT
button.
Stop-Eject
To stop playing a tape, fully press this button. The
cassette will eject, and the radio will begin playing.
To Play This Radio
Power
Press PWR to turn the unit on and off when the ignition
is
on.
130
ProCarManuals.com

Upper Knob
This knob does two things:
0 Rotate VOL slightly to the left or right to control the
volume.
0 Press it to mute the radio or tape player. Press again
to listen.
Balance
The BAL control behind the upper knob adjusts the
left/right speaker balance.
Lower Knob
This knob does two things:
0 Rotate TUNE slightly to the left or right to tune in
radio stations. If you hold it to the left or right, it will
tune rapidly.
0 Press to change between the AM and FM bands. The
band you select will appear on the digital display.
Fade
The FADE control behind the lower knob adjusts the
front/rear speaker balance.
Scan
Press the SCAN button to hear each station for a few
seconds. Push
it again to stop scanning.
Seek
Press the SEEK button to go to the next higher station
and stay there. Push
it again and it will find the next
higher station.
Recall
Press RCL to alternate the display between the time and
station frequency. When the ignition
is off, press to
display the time.
Bass
Press BASS up or down to increase or decrease the bass
level. Press the center of
the button for the factory preset
level.
Treble
Press TREB up or down to increase or decrease the
treble level. Press
the center of the button for the factory
preset level.
If a station is weak or noisy, reduce the
treble.
131
ProCarManuals.com

Random Scan
Press
RDM to play tracks in random, rather than
sequential, order. Press the button again to play tracks
sequentially.
Reverse
Press REV and hold to rapidly back up to a favorite
passage. Release to resume playing.
Fast Forward
Press FWD and hold to rapidly advance the disc.
Release to resume playing.
Previous
Press PREV to play a track again. If you hold or keep
pressing the PREV button, the disc will keep backing
up
to previous tracks.
Next
Press NEXT when you want to hear the next track. If
you hold or keep pressing the NEXT button, the disc
will keep advancing to other tracks. Press SCAN
to play each track for approximately ten
seconds. Scan will continue until SCAN is pressed again
or another button is pressed.
Stop/Play
Press STPL to stop the disc player; the radio will play.
Press again
to play the disc (the player will start playing
the disc where
it was stopped earlier).
Eject
Press EJCT to eject the disc; the radio will play. You can
also eject the disc with the radio
or ignition off.
If you press PWR or turn off the ignition, the disc will
stay
in the player and start again when you turn on the
ignition or power switch. The disc will begin playing at
the point where
it had been stopped.
133
ProCarManuals.com

CD Player Anti-Theft Feature
Delco LOC I1 is a security feature for the compact disc
player.
It can be used or ignored. If ignored, the system
plays normally. If it is used, your player won’t be usable
if
it is ever stolen, because it will go to LOC mode any
time battery power
is removed. Until an unlock code is
entered, it will
not turn on.
The instructions below tell you how to enter a secret
code into the system. If your vehicle loses battery power
for any reason, you must unlock the system with the
secret code before the radio will turn on. Be sure to read
through
the entire procedure and become familiar with
the appropriate buttons and knobs before starting.
1. Write down any six-digit number and keep it in
a
safe place.
2. Turn the ignition to the ACC or RUN position.
3. Press the PWR button to turn the radio off.
4. Press the 1 and 4 pushbuttons together. Hold them
down
until “---” shows on the display.
You are ready to enter your secret code. If you pause
more than
15 seconds between steps, you may have
to start the procedure over.
5. Press SET and “000” will appear on the display.
6. Press the SEEK button to make the first number
appear.
7. Rotate the TUNE knob right or left to make the last
two numbers agree with your code.
8. Press the lower (BAND) knob and “000” will appear
again.
Now you are ready to enter the last three digits of
your code by repeating steps
6 and 7 for the last
three digits
of your code.
9. Press the lower (BAND) knob and “rEP” will appear
for
five seconds and then “000” will appear
indicating that some steps are to be repeated.
10. Repeat steps 6,7 and 8.
11. Press the lower (BAND) knob. If the display shows
“SEC” it indicates that the process was successful
and the radio is secure. If
the display shows “---,”
the steps were not successful and the process must be
repeated
to secure.
134
ProCarManuals.com

To Unlock the System After a Power Loss
When battery power is reapplied to a secured radio, the
radio won’t turn on and “LOC” will appear on the
display. Enter your secret code as follows; pause no
more than
15 seconds between steps.
1. Turn the ignition on. (Radio off.)
2. Press the SET button. The display will show “000.”
3. Enter the six digits of your code following steps 6-9
on the preceding. The display will show the numbers
as entered.
4. Press the lower (BAND) knob and SEC appears,
then the time, indicating that the disabling sequence
was successful.
Disabling the Anti-Theft System:
1.
2.
3.
4.
5.
6.
Press the I and 4 buttons together for five seconds with
ignition on and radio power off. The display will show
“SEC,” indicating the unit is in the secure mode.
Press the
SET button. The display will show “OOO.”
Enter the first three digits of your code following
step
6 and 7of the preceding paragraphs. The display
will show the numbers as entered.
Press the lower (BAND) knob. The radio will
display
“000.”
Enter the second three digits of the code. The display
will show
the numbers as entered.
Press the lower (BAND) knob.
If the display shows
numbers matched the user-selected code or
the
factory back-up code) and the unit is in the
UNSECURED mode. If
the display shows “SEC,”
the disabling sequence was unsuccessful and the numbers did
not match either of the codes and the
unit will remain in the SECURED mode.
“--- , ” the disabling sequence was successful (the
135
ProCarManuals.com

Power Antenna Mast Care
Your power antenna will
look its best and work well
if it’s cleaned from time
to
time.
To Clean the Antenna Mast:
1. Turn on the ignition and radio to raise the antenna to
full mast extension.
2. Dampen a clean cloth with mineral spirits or
3. Wipe cloth over the mast sections, removing any dirt.
equivalent
solvent.
4. Wipe dry with clean cloth before retracting.
5. Make the antenna go up and down by turning the
6. Then repeat if necessary.
radio
or ignition on and
off.
NOTICE:
Don’t lubricate the power antenna. Lubrication
could damage
it. I
NOTICE:
Before entering an automatic car wash, turn off
your radio to make the power antenna go down.
This will prevent the mast from possibly getting
damaged. If the antenna does
not go down when
you turn the radio
off, it may be damaged or need
to be cleaned.
In either case, lower the antenna
by hand by carefully pressing the antenna down.
137
ProCarManuals.com

NOTICE:
Ignoring these steps could result in costly
damage to your vehicle that wouldn’t be covered
by your warranty.
Trying to start your Buick by pushing or pulling
it
won’t work, and it could damage your vehicle.
To Jump Start Your Buick:
1. Check the other vehicle. It must have a 12-volt
battery with a negative ground system.
I NOTICE:
I
If the other system isn’t a 12-volt system with a
negative ground, both vehicles can be damaged.
2. Get the vehicles close enough so the jumper cables
can reach, but be sure the vehicles aren’t touching
each other.
If they are, it could cause a ground
connection
you don’t want. You wouldn’t be able to
start your car, and the bad grounding could damage
the electrical systems.
3. Turn off the ignition on both vehicles. Turn off all
lights that aren’t needed, and radios. This will avo
sparks and help save both batteries. And it could
save your radio! ‘id
I NOTICE:
If you
leave your radio on, it could be badly
damaged. The repairs wouldn’t be covered by
your warranty.
4. Open the hoods and locate the batteries.
Find the positive
(+) and nenative (-) terminals on each
battery.
174
ProCarManuals.com