1993 OLDSMOBILE SILHOUETTE wheel bolts

Parking on Hills
You really should not park your vehicle,
with a trailer attached, on a hill. If
something goes wrong, your rig could
start to move. People can be injured,
and both your vehicle and the trailer can
be damaged.
But if you ever have to park your rig on
a hill, here’s how to do it:
1 . Apply your regular brakes, but don’t
shift into
P (Park) yet.
2. Have someone place chocks under
the trailer wheels.
3. When the wheel chocks are in place,
release the regular brakes until the
chocks absorb the load.
apply your parking brake, and then shift to
P (Park).
4. Reapply the regular brakes. Then
5. Release the regular brakes.
When You Are Ready to Leave After
Parking on a Hill
1. Apply your regular brakes and hold
the pedal down while you:
Start your engine;
Shift into a gear; and
Release the parking brake.
2. Let up on the brake pedal.
3. Drive slowly until the trailer is clear
4. Stop and have someone pick up and
of the chocks.
store the chocks.
Maintenance When Trailer
Towing
Your vehicle will need service more
often when you’re pulling a trailer. See
the Maintenance Schedule for more on
this. Things that are especially
important in trailer operation are
automatic transaxle fluid (don’t overfill)
engine oil, belts, cooling system, and
brake adjustment. Each
of these is
covered in this manual, and the
Index
will help you find them quickly. If
you’re trailering, it’s a good idea to
review these sections before you
start
your trip.
Check periodically
to see that all hitch
nuts and bolts are tight.
183
ProCarManuals.com

13. Remove any corrosion or dirt from I 14. Replace the wheel nuts with the
the wheel bolts, mounting surfaces
or spare wheel. Place the spare on
the wheel mounting surface.
Never use oil
or grease on I
~ studs or nuts. If you do, the
I nuts might come loose. Your whel
luld fall
off, causing a serious
accident.
1
rounded end of the nuts toward the
wheel. Tighten each
nut by hand
until the wheel is held against the
hub.
1 5. Lower the vehicle by attaching the
folding wrench
to the jack and
rotating the wrench counter-
clockwise. Lower the jack
completely.
1
209
ProCarManuals.com

Service & Appearance Care
252
Temperature-A, B, C (CONT)
Warning: The temperature grade for
this tire is established for a tire that is
properly inflated and not overloaded. Excessive speed, underinflation, or
excessive loading, either separately or in
combination, can cause heat buildup
and possible tire failure.
Those grades are molded on the
sidewalls of passenger car tires.
While the tires available as standard or
optional equipment on General Motors
vehicles may vary with respect to these
grades, all such tires meet General
Motors performance standards and have
been approved for use on General Motors vehicles.
All passenger type
(P Metric) tires must conform to Federal
safety requirements in addition to these
grades.
Wheel Alignment and
Tire Balance
The wheels on your vehicle were
aligned and balanced carefully at the
factory to give you the longest tire life
and best overall performance.
In most cases, you will not need to have
your wheels aligned again. However,
if
you notice unusual tire wear or your
vehicle pulling one way or the other, the
alignment may need to be reset. If you
notice your vehicle vibrating when
driving on a smooth road, your wheels
may need to be rebalanced.
Wheel Replacement
Replace any wheel that is bent, cracked
or badly rusted. If wheel nuts keep
coming loose, the wheel, wheel bolts,
and wheel nuts should be replaced. If
the wheel leaks air out, replace it
(except some aluminum wheels, which
can sometimes be repaired). See your
Oldsmobile dealer
if any of these
conditions exist.
Your dealer will know the kind of wheel
you need.
Each new wheel should have the same
load carrying capacity, diameter, width,
offset, and be mounted the same way as
the one it replaces.
If you need
to replace any of your
wheels, wheel bolts, or wheel nuts,
replace them only with
new GM
original equipment parts.
This way, you
will be sure you have the right wheel,
wheel bolts, and wheel nuts for your Oldsmobile model.
ProCarManuals.com

Used Replacement Wheels Tire Chains
Using the wrong replacement
b wheels, wheel bolts, or wheel
nuts on your vehicle can be
dangerous. It could affect the
braking and handling
of your
vehicle, make your tires lose air
and make you lose control. You
could have a collision in which you
)r others could be injured. Always
lse the correct wheel, wheel bolts,
1 and wheel nuts for replacement.
IL
The wrong wheel can also cause
problems with bearing life, brake cooling, speedometer/odometer
calibration, headlight aim, bumper
height,
vehicle ground clearance,
adtire
or tire chain clearance to
.the-body
.~ and chassis,;f,;,ir, ~ ~~~ .. .~. ..~ = ~ ~=.=.=~~~~ ... ~~
Putting a used wheel on your
vehicle is dangerous. You
can t
know how it’s been used or
how many miles it’s been driven. It
-ould fail suddenly and cause an
,ccident. If
you have to replace a
wheel, use
a new GM original
equipment wheel.
e
Use tire chains only when y
must. Use only SAE Class ‘23’’
type chains that are the proper size
for your tires. Install them on the
front tires and tighten them as
tightly as possible with the ends
securely fastened. Drive slowly
and follow the chain manu-
facturer’s instructions. If
you can
hear the chains contacting your
vehicle, stop and retighten them.
If
the contact continues, slow down
until it stops. Driving too fast with chains on will damage your
vehicle.
:l I ’
I
. .. ..
253
ProCarManuals.com

Maintenance Schedule
Section A: Scheduled Maintenance Services (Cont.)
284
Explanation of Scheduled Maintenance Services
Below are explanations of the services listed in Schedule I
and Schedule II.
The proper fluids and lubricants to use are listed in
Section D. Make sure whoever services your vehicle uses
these. All parts should be replaced
and all necessary repairs
done before you or anyone else drives the vehicle.
ITEM
NO. SERVICE
1 Engine Oil and Filter Chang@-Always use SG
Energy Conserving
II oils of proper viscosity. The
“SG” designation may be shown alone or in
combination with others, such as “SG/CC,” “SG/CD,” or
“SF, SG, CC,” etc. To determine the
preferred viscosity for your vehicle’s engine (e.g.,
SAE 5W-30 or SAE 10W-30), see the
Index under
Engine Oil.
2 Chassis Lubrication-Lubricate the transaxle shift
linkage, parking brake cable guides, underbody
contact points and linkage. Lubricate the front
suspension and steering linkage. NOTE:
To determine your engine’s displacement and code,
see the
Index under Engine IdentiJication.
ITEM
NO. SERVICE
3 Throttle Body Mounting Bolt Torque (3.a
Code D engine only) *-Check the torque of the
mounting bolts and/or nuts.
4 Tire and Wheel Rotation and Inspection-For
proper wear and maximum tire life, rotate your
tires following the instructions
in this manual. See
the
Index under Eres, Inspection & Rotation.
Check the tires for uneven wear or damage. If you
see irregular or premature wear, check the wheel
alignment. Check for damaged wheels
also.
* An Emission Control Senice.
ProCarManuals.com