1993 Oldsmobile Cutlass Supreme lights

Vehicle Symbols
These are some of the symbols you
will find on your vehicle. For
example, these
symbols are used on
an original battery:
Caution Possible Injury A
Protect Eyes by
Shielding
Caustic Battery Acid
Could Cause Burns
Avoid Sparks or Flames
8
Spark or Flame Could Explode Battery
These symbols are important for you
and your passengers whenever your
vehicle
is driven:
Fasten Safety Belts
Door LocklUnlock
These symbols have to do with your
lights:
Master Lighting Switch
Turn Signal Direction
Hazard Warning Flashers
A
Headlight High Beam Parking Lights Fog Lights
pf
#O
9

1
How to Use this Manual
I
Wehicle Symbols (CONTJ
These symbols are on some of your
controls: These symbols are used on warning
and indicator lights:
Windshield Wipers
Engine Coolant
Temperature
Windshield Washer
Windshield Defroster
Rear Window Defogger Ventilating Fan
Power Window
Here are some other symbols you
may see:
Fuse
Battery Charging
System Trunk Release
Lighter
Fuel
Engine
Oil Pressure
Brake
Anti-Lock Brakes Horn
Speaker
Hood Release
b

This figure lights up when you turn the
key to
Run or Start when your safety
belt isn’t buckled, and you’ll hear a
chime, too. It’s the reminder to buckle
up. In many states and Canadian
provinces, the law says to wear safety
belts. Here’s why:
They work.
You never lmow if you’ll be in a crash.
If you do have a crash, you don’t how
if it will be a bad one.
A few crashes are very mild. In them,
you won’t get hurt even if you’re not
buckled up. And some crashes can be
so serious, like being hit by a train, that
even buckled up a person wouldn’t survive. But most
crashes are in
between. In many
of them, people who
buclde up can survive and sometimes
walk away. Without belts they could be
badly hurt
or killed.
After
25 years of safety belts in vehicles,
the facts are clear. In most crashes
buckling up does matter
. . . a lot!
17

Run: An “on” position to which the
switch returns after you start your
engine and release the switch. The
switch stays in the
Run position when
the engine is running. But even when
the engine is not running, you can use
Run to operate your electrical power
accessories, and to display some instru-
ment panel warning lights.
Start: Starts the engine. When the
engine starts, release the ley. The
ignition switch will return to
Run for
normal driving.
Note that even
if the engine is not
running, the positions
Accessory and
Run are “on” positions that allow you
to operate your electrical accessories,
such as the radio.
Starting Your Engine
1. Move your shift lever to P (Park) or
N (Neutral). Your engine won’t start
in any other position-that’s a safety
feature.
To restart when you’re
already moving, use
N (Neutral)
only.
2. Don’t push the accelerator pedal
before starting your engine. In some
other vehicles you might need to do
this, but because of your vehicle’s
computer systems, you don’t.
55

Features & Controls
76
Windshield Washer (CONT.)
Push the switch in all the wa
on the headlights, together u
Parking Lights
Running Lights
Taillights
Instrument Panel Lights
1y to turn
rith the:
Push the switch again to turn the lights
Off.
A green indicator light in the center of
the switch will come on when you start
the engine. This helps you locate the
switch at night.

Lights On Reminder
If you open the door while leavmg. the
lights on, you will hear a warning tone.
1
77

Features & Controls
78
Daytime Running Lights (CONK)
At dusk, the exterior lights will come on
automatically and the low beams will
change to full brightness. At dawn, the
exterior lights will go out and the low
beams will change to the reduced
brightness of
DRL (if the headlight
switch is off).
Of course, you may still turn on the
headlights any time you need to.
To idle your vehicle with the DRL off,
set the parking brake while the ignition
is in the
Off or Lock position. Then
start the vehicle. The DRL will stay off
until you release the parking brake.
Headlight High-Low Beam
Changer
To change the headlights from low
beam to high or high to low, pull the
turn signal/headlight beam lever all the
way toward you. Then release it.
When the high beams are on,
a blue
light on the instrument panel also will
be on.
Flash-to- Pass
Flash-to-pass lets you use your high
beam headlights
to signal a driver in
front of you that you want to pass.
To use it, pull the turn signal/headlight
beam lever toward you.
If Your Headlights are Off
Your high beam headlights will turn on.
They'll stay on
as long as you hold the
lever there. Release the lever to turn
them off.
If Your Headlights are On:
No flash-to-pass. Use the lever to
change between high and low beams, as
explained under
Headlight High-Low
Beam Changer
earlier in this section.
If You Have Fog Lights:
They go off whenever the high beams
are on. When the high beams go
off, the
fog lights will come on again, if the fog
light switch is on.

Insfrum~e~t Panel hfensity
Control
You can brighten or dim the instrument
panel lights by sliding the control hob
up or down. If you slide the hob all the
way up to
INT your courtesy or interior
lights
will come on. To turn instrument
panel lights on to
full intensity with the
headlights on, slide the control hob
to
MAX.
Fog (OPTION)
Use your fog lights for better vi'sion in
foggy or misty conditions.
To turn fog lights on, push the switch.
Push the-switch again to turn the fog
lights off.
When using fog lights, the parlung
lights or low beam headlights must be on.
The fog lights will go
off whenever the
high beam headlights come on. When
the high beams go
off, the fog lights will^
come on again.
Front ReadinglMap Ljghfs
(OPTION)
These lights are part of the rearview
mirror. They go on when you open the
doors. When the doors are closed, turn
them on
and off with the switch.
To avoid draining your vehicle battery's
power, be sure
to turn off all front and
rear reading lights-when leaving your
vehicle.
79