1993 Oldsmobile Cutlass Supreme display

Run: An “on” position to which the
switch returns after you start your
engine and release the switch. The
switch stays in the
Run position when
the engine is running. But even when
the engine is not running, you can use
Run to operate your electrical power
accessories, and to display some instru-
ment panel warning lights.
Start: Starts the engine. When the
engine starts, release the ley. The
ignition switch will return to
Run for
normal driving.
Note that even
if the engine is not
running, the positions
Accessory and
Run are “on” positions that allow you
to operate your electrical accessories,
such as the radio.
Starting Your Engine
1. Move your shift lever to P (Park) or
N (Neutral). Your engine won’t start
in any other position-that’s a safety
feature.
To restart when you’re
already moving, use
N (Neutral)
only.
2. Don’t push the accelerator pedal
before starting your engine. In some
other vehicles you might need to do
this, but because of your vehicle’s
computer systems, you don’t.
55

9.2
h
Speedometer
(ELECTRONIC CLUSTER)
Press the E/M (English/Metric) button
on the le& side of the instrument cluster
to switch the display between miles per
hour (mph) and kilometers per hotrr
*
Odometer and Trip Odometer
(ELECTRONIC CLUSTER)
Your odometer shows how faryour
vehicle has been driven,
.in either miles
(used in the U.S.) or in kilometers
(used in Canada). YQW trip odometer
tells how far
you have driven since you
last reset it.
To set it to zero, display~the
trip odometer
by pressing the SELECT
button, then press the RESET button.
Both buttons are located on the right
side
of the instrument cluster. Your Oldsmobile
has a tamper resistant
odometer. The odometer
will read
EKROR if someone has ,tampered with
it.
You may wonder what happens if your
vehicle needs
a new odometer installed.
If the new one can be s&to the mileage
total
of the old odometer, then it must
be. But
if it can’t, then it’s set at zero
and a label must be put on the- driver’s
door to show the old mileage reading
when
the llew odometer was installed.

~ Features & Controli
Tachomefer ~WUOG CLUSTER)
The tachometer displays the
engine
speed
in revolutions per rninute (rpm) .
E

Features & Controls
I
104
Head-Up Display (CONT.)
Pushing the ENG/MET rocker switch
on the center console
will switch the
HUD speedometer from English
(conventional) to metric units, or back
again.
Some vehicles may not be
equipped
with the ENG/MET switch.
Care of the Head-Up Display
Clean the inside of the windshield as
needed to remove any dirt or
film that
reduces the sharpness
or clarity of the
HUD image.
To Clean the HUD:
Spray household glass cleaner on a soft,
clean cloth. Wipe the HUD lens gently,
then
dry it. Do not spray cleaner
directly on the lens, because the cleaner
fluid could leak inside the unit
if you do.
If You Can’t See the HUD Image
When the Ignition
is On:
Is anything cbvering the HUD unit?
Is the HUD dimmer control close
enough
to MAX?
Is the HUD image-adjusted to the
proper height?
Still no HUD image? Check the fuse
in the
CLUST position in the glove
box fuse panel. See the Index under
Fuses G Circuit Breakers.
..

Electronic Climate Control
(OPTION)
This system allows you to set the
temperature you want. It also lets you
choose automatic air flow and direction
control, or air flow and direction
settings you select. Your vehicle
also
has the flow-through ventilation system
described later in this section.
The digital screen displays the outside
temperature, the inside temperature
setting and the fan speed.
When you select the
AUTO mode, the
air conditioner compressor will operate
if the outside temperature is above
freezing.
113

Comfort Controls &Audio Systems
Ekctronic Climate Control
114
(Cont.)
temperature caused by sunlight. To
keep you comfortable, it reduces the
interior temperature by as much as 5°F
(3°C) below the setting
on the digital
screen.
AUTO: To allow the system to
automatically control the temperature,
air distribution and fan speed:
1. Set the temperature you want with
the
COOL/WARM switch.
2. Press the AUTO switch. The AUTO
symbol will appear on the digital
screen.
The system will approach the
temperature you select as quickly as
possible. For most efficient operation,
just set the system temperature where
you would like it and drive away.
OUTS TEMP: Press to have the
outside temperature displayed on the
digital screen. Press again to return to
the inside temperature setting.
If the system is left in the outside
temperature mode, the outside
temperature will be displayed except
when changing the inside temperature
setting using the
COOL/WARM
switch. The display will return to the
outside temperature setting in about
five seconds. Use
the following controls when the
system is not set on
AUTO:
8: Press the top of the switch to raise
the fan speed, the bottom of the switch
to lower the fan speed. The fan symbol
and bar graph will be displayed on the
digital screen.
When the
AUTO switch is pressed, the
fan symbol will go out and the fan will
return to automatic operation.
If the Fahrenheit (F") or Celsius (C")
symbol begins to flash, or flashes when
you turn on the ignition,
it indicates an
electrical problem with your air conditioning system. The flashing
will
continue for about two minutes. It
means
you should have your system
serviced.

116
Comfort Controk &Audio Systems
Steering Wheel Touch Controls
for Climate Control
(OPTION)
Some heating and cooling controls can
be adjusted at the steering wheel. These
touch controls also operate some audio
controls. See the
Index under Steering
Wheel
Touch Controls for Audio
System.
FAN: Press the upper part of the
control to increase the fan speed; press
the lower part to reduce the fan speed.
TEMP: Press the upper part of the
control to raise the inside temperature
setting; press the lower part to lower
the setting.
MODE: This control can be used to
select the direction of air flow
(BI-LEV, UPPER, or LOWER
settings), or to select DEFOG,
DEF
(Defrost) or AUTO. Press the top
of the control to move to the next mode
on the right of the climate control
panel. Press the bottom
of the control
to move to the next mode on the left.
The indicator light will glow above the
selected mode, or
AUTO will appear on
the digital display.
Rear Window Defogger (OPTION)
R DEFOG: Press to warm the
defogger grid on the rear window. The
indicator light will glow while the rear
window defogger is operating. The rear
window defogger will turn off
automatically after about
10 minutes of
use. If you turn it on again, the defogger
will operate for about five minutes only.
You can also turn the defogger off by
turning off the ignition or pressing the
R DEFOG switch again.
Do not attach a temporary vehicle
license across the defogger grid
on the
rear window.

For Radios with SCAN and SEEKA
and SEEKV:
1. With the radio off and the ignition
on, press
SET. The SET indicator
will appear on the digital screen for
five seconds.
2. Press and hold SCAN until the
correct hour appears on the display.
3. Press SET again.
4. Press and hold SEEK A or SEEKV
until the correct minute appears on
the display.
R . ,._
Pi
L ..
as
4MIFM Stereo Radio
The digital display indicates information
3n time or radio station frequency, the
AM or FM radio band, whether the
station is in stereo, and other radio
€unctions.
VOLUME: Turn the upper knob to
turn the radio on or off, or to adjust
volume. Press it to change the display
between the clock and the radio station
hequency when the radio is
on.
The control ring behind the VOLUME
knob adjusts the lefthight speaker
balance.
TUNE: This knob has two functions.
Turn it to the left or right to tune in
radio stations (the radio station
frequency will be displayed on the
digital screen). Press this knob to
change between the AM and FM bands.
119