1993 NISSAN SERENA weight

ADJUSTMENT
(Model
H190A
l- ,, Side
Be€ring Preload (Cont'd)
3. Measure how laf
under lhe slandad lhckness
[20 mm
(0.79 in)lfte side b€annss
are.
ll wiLlGquire tools shown
n lhe ilustration al
letl
O wolqhl
Block (ST32501000)
O Marl€r
Gause (xv331o19oo)
A. Lubicale 6
d€ beadng and
da@the bearn9oul.r
ra€and
inner6c6 rob6
m6asu rcd on lhe opposile side olld
a€.
ll the ba.dng.embly b plaed
d ltF bte pLL,lh6
beaF
ing wldth €nnot be
suErdy d.Lrnined dE b n5
ega
b.ing in contacl whh tie b4 pl.r..
9 Pla€
weight block or sde bea ng.
10. Slde dia indi€tor
on weighl b ock.
P
ace th€
ouler ra@ o1 fie opposile s
do
Placo a weighl block on
lhal outer ra@,
adjusl dial ndicalorscae to 2ero
Carelllly side
masler gauge
and weiqhl
Tum weghl block a
few limes to ensure thal beaing ls
0.1O -
0.lll nn (0.m39 -
Ofi 1a In)
t ttE needle iuctualqs en llelly llEn
b.5ri.g i5 .ilh€r
diny or dehtire and should be derEd d
€plac.d.
'12.
Pt!44

HEADLAMP
PUSH Io
\
_@. PUSH
lo Bulb
Replacement
The headlamp is
a semi-sealed beam type which
uses a
replaceable halogen
bulb. The
bulb can
be replaced from
the
f ront compartment side without
removing the headlamp
body.
r Grasp
only the plastic
base when
handling the bulb.
Never
touch the glass
envelope.
1. Disconnect the
battery cable.
2. Disconnect the
harness connector from
the back side ol the
bulb.
3. Pull
off the
rubber cap.
4. Remove the headlamp
bulb carefully. Do
not shake or
rotate the bulb when removing it.
5. Install
in the reverse
order of removal.
CAUTION:
o Do
not leave the bulb out of the headlamp
reflector for a
long period
of time as dust, moisture,
smoke, etc. may
enter the headlamp
body and aflect the pedormance
of the
headlamp. Thus, the headlamp
bulb should not
be
removed from
the headlamp reflector until just
before a
replac€ment bulb is
to be installed.
Aiming Adjustment
When performing
headlamp aiming adjustment, use
an aiming
machine, aiming wall screen or headlamp
lester. For
operating
instructions of any aimer, it should be in good
repair, calibrated
and used according to
respective operation manuals
supplied
with the unit.
lf any aimer is
not available, aiming adjustment can be done as
Iollows:
For details, reter
to the regulations in your
own country.
CAUTION:
a. Keep all tires inflated to correcl pressures.
b. Place vehicle
and tester on one
and same flat surface-
c. See that there
is noload in vehicle (coolant,
engine oil filled
up to correct level
and tull tuel tank) other than the driver
(or equivalent weight placed
in driver's position).
CAUTION: Be sure aiming switch
is set to "0"
when performing
aiming
adiustment on
vehicles equipped with
headlamp
aiming con-
trol.
lF-bl
l3 2
I 0l
L,\_-! S l l
,n
[) \/
EL-49