1993 GMC SIERRA manual transmission

Engine Fan Noise
This vehicle has a clutched engine cooling fan. When the clutch is engaged,
the fan spins faster to provide more air to
cool the engine. In most every day
driving conditions the clutch is not engaged. This improves fue\
l economy and
reduces fan noise. Under heavy vehicle loading, trailer towing andlor high
outside temperatures, the fan speed increases when the clutch e\
ngages.
So
you may hear an increase in fan noise. This is normal and should not be
mistaken as the transmission slipping or making extra shifts. It is merely the
cooling system functioning properly. The fan will
slow down when additional
cooling is not required and the clutch disengages.
You may also hear this fan noise when you start the engine. It will go away
as the fan clutch disengages.
If a Tire Goes Fiat
It’s unusual for a tire to “blow out” while you’re driving, especially if you
maintain your tires properly. If air goes out of a tire, it’s much more likely to
leak out slowly. But
if you should ever have a “blowout,” here are a few tips
about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that pulls the vehicle toward
that side. Take your foot off the accelerator pedal and grip \
the steering wheel
firmly. Steer to maintain lane position, then gently brake to a stop well out of
the traffic lane.
A rear blowout, particularly on a curve, acts much like a skid and may
require the same correction you’d use in a skid. In any rear blowout, remove
your foot from the accelerator pedal. Get the‘vehicle under control by steering
the way you want the vehicle to go. It may be very bumpy and noisy, but
you can still steer. Gently brake to a stop, well off the road
if possible.
If your tire goes flat, the next part shows how to use your jacking equipment
to change a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage by driv\
ing slowly to a
level place. Turn on your hazard warning flashers.
5-1 7
ProCarManuals.com

Pmb/ems on the Road
vnu I IVII
A Changing a tire can cause an injury. The vehicle can slip off the iac
and roll over you or other people. You and they could be badly
injured. Find
a level dace .. , to ,dbanr voy&&g. To heh Drevent tt-
fehicle from m
E -,>1-
-ut the shift lever in P (P
hift a manual transmission to 1 (First) ur r never 3.
To be even more certain the vehicle won’t move, you can put c\
hocks
at the front and rear of the tire farthest away from the one being
changed. That would be the tire on the other side of the vehicle, at
the opposite end.
.
AM545004
The following steps will tell you how to use the jack and ch\
ange a tire.
The equipment you’ll need is behind the passenger’s seat. \
Your spare tire is
stowed under the truck or behind the driver on the side of the truck bed.
5-1 8
ProCarManuals.com

If You’re Stuck: In Sand,
Mud,
Ice or Snow
What you don’t want to do when your vehicle is stuck is to spin your
wheels. The method known as “rocking” can help you get o\
ut when you’re
stuck, but you must use caution.
CAUTION - --
I * If you let your tires spin at high speed, they can explode and you or
,A others could be injured. And, the transmission or other parts of the
vehicle can overheat. That could cause an engine compartment fire
or other damage. When you’re stuck, spin the wheels as little as
possible. Don’t spin the wheels above
35 mph (55 krnlh) as shown
I on the speedometer.
;pinning your wheels can destroy parts of your vehicle as well as the
res.
If you spin the wheels too fast while shifting your transmission back
.nd forth, you can destroy your transmission.
NOTICE 1
Rocking your vehicle to get it out:
First, turn your steering wheel left and right. That will clear the area around
your front wheels. Then shift back and forth between
R and a forward gear
(or with a manual transmission, between First or Second gear and Reverse),
spinning the wheels as little as possible. Release the accelerator pedal while
you shift, and press lightly on the accelerator pedal when the transmission is
in gear.
If that doesn’t get you out after a few tries, you may need to be
towed out.
Or, you can use your recovery hooks, if your vehicle has them. If
you do need to be towed out, see “Towing Your Vehicle” in the Index.
5-33
ProCarManuals.com

Service & Appearance Care
.....
Here you will find information about the care of your vehicle . This Section
begins with service and fuel information. and then it shows how to check
important fluid and lubricant levels
. There is also technical information about
your vehicle. and a section devoted to its appearance care
.
Service ........................................................................\
........................................... 6-3
Fuel (Gasoline Engines)
........................................................................\
............... 6-4
Diesel Fuel Requirements and Fuel System
...................................................... 6-6
Checking Things Under the Hood
..................................................................... 6-17
Hood Release
........................................................................\
.......................... 6-18
Cleaning Your Diesel Engine
........................................................................\
.. 6-19
Noise Control System
........................................................................\
............. 6-19
Engine Oil (Except Diesel)
........................................................................\
..... 6.20
Engine Oil (Diesel Engines)
........................................................................\
... 6-26
Air Cleaner
........................................................................\
............................... 6-31
Automatic Transmission Fluid
........................................................................\
. 6-33
Manual Transmission Fluid
........................................................................\
..... 6-36
Hydraulic Clutch
........................................................................\
....................... 6-37
Transfer Case
........................................................................\
.......................... 6-39
Front Axle ........................................................................\
................................. 6-40
Rear Axle
........................................................................\
................................. 6-41
6-1
ProCarManuals.com

Automatic Transmission Fluid
When to Check and Change:
A good time to check your automatic transmission fluid level is when the
engine oil is changed. Refer
to the Maintenance Schedule to determine when
to change your fluid. See "Scheduled Maintenance Services" in the \
Index.
How to Check:
Because this operation can be a little difficult, you may choose to have this
done at a General Motors dealership Service Department.
If you
do it yourself, be sure to follow all the instructions here, or you could
get a false reading on the dipstick.
I Too much or too little fluid can damage your transmission. Too much can
nean that some of the fluid could come out and fall on hot engine parts,
itarting
a fire. Be sure to get an accurate reading if you check your
ransmission ftuid.
Wait at least
30 minutes before checking the transmission fluid level if you
have been driving:
When outside temperatures are above 90°F (32°C).
At high speed for quite a while.
In heavy traffic-especially in hot weather.
While pulling a trailer.
To get the right reading, the fluid must be at normal operating temperature,
which is 180°F
to 200°F (82°C to 93°C).
To check the transmission fluid hot: Get the vehicle warmed up by driving
about
15 miles (24 km) when outside temperatures are above 50°F (1 0°C). If
it's colder than
50°F (lO°C), drive the vehicle in D (3rd gear) until the engine
temperature gage moves and then remains steady for ten minutes. Then
follow the hot check procedures.
To check transmission fluid cold: A cold check is made after the vehicle
has been sitting for eight hours or more with the engine
off and is used only
as a reference. Let the engine run at idle for five minutes
if outside
temperatures are 50°F (10°C) or more.
If it's colder than 50°F (lO"C), you
may have
to idle the engine longer. A hot check must follow when fluid is
added during a cold check.
6-33
ProCarManuals.com

3. Check both sides of the dipstick, and read the lower level. The fluid
level must be in the
COLD area for a cold check or in the HOT area or
cross-hatched area for a hot check.
4. If the fluid level is where it should be, push the dipstick back in all the
way; then flip the handle down to lock the dipstick in place.
How To Add Fluid:
Refer to the Maintenance Schedule to determine what kind of transmission
fluid
to use. See “Recommended Fluids and Lubricants’’ in the Index.
If the fluid level
is low, add only enough of the proper fluid to bring the level
up
to the COLD area for a cold check or the HOT area for a hot check. It
doesn’t take much fluid, generally less than a pint. Don’t overfill. We
recommend you use only fluid labeled DEXRON@IIE, because fluids \
with that
label are especially made for your automatic transmission. Damag\
e caused by
fluid other than
DEXRON@IIE is not covered by your new vehicle warranty.
After adding fluid, recheck the fluid level as described under “How To
Check”.
When the correct fluid level is obtained, push the dipstick back in all the
way; then flip the handle down
to lock the dipstick in place.
6-35
ProCarManuals.com

*
Senrice & Appearance Care
Manual Transmission Huld
When to Check:
the fluid in your manual transmission doesn't require changing.
How to 'Check:
Because this operation can be a :little difficult, you may cho\
ose to have this
done at your dealership Service Department.
t A good time to have it checked is when .the engine oil is changed. However,
If you do it yourself, be sure to follow' all the instructions here, or you could
get a false reading..
. . .. . . ... -
Too much or too little fluid can damage your transmission. Too much can
mean that some of the fluid could come out and fall on hot engine parts,
starting a fire. Be sure
to get an accurate reading if you check your
transmission fluid.
Check the fluid level only when your engine is
off, the vehicle is parked on a
level place and the transmission is cool enough for you to re\
st your fingers
on the transmission case.
Then, follow these steps:.
~ ~~ ~
1. Remove the filler plug.
K2471
2. Check that the lubricant level is up to the bottom of the filler- plug hole.
3. If the fluid level is good, install the plug and be sure it is fully seated. If
the fluid level is low, add more fluid as described in the next steps.
6-36
ProCarManuals.com

Scheduled Maintenance Services
Explanation Of Scheduled Maintenance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed in this section. Make sure
whoever services your vehicle uses these. All parts should be \
replaced and
all necessary repairs done before you or anyone else drives the ve\
hicle.
1.
ENGINE OIL AND OIL FILTER CHANGE* -ALWAYS USE SG OR
SGKE QUALITY, ENERGY CONSERVING II OILS OF THE PROPER
VISCOSITY. To determine the preferred viscosity oil for your vehicle’s
engine (e.g. SAE 5W-30 or 10W-30), see “Engine Oil” in the Index.
2. CHASSIS LUBRICATION -Lubricate the front suspension, king pin
bushings, steering linkage, transmission, and transfer case shift\
linkage,
parking brake cable guides, propshaft splines (2 wheel drive), brake
pedal springs, and clutch pedal springs at the intervals specified.
If you have a 3500 HD, lubricate the king pins and king pin bushings
every 1,500 miles
(2500 km) for Maintenance Schedule 1, or every 3,000
(5000 km) for Maintenance Schedule 2.
Ball joints and king pin bushings should not be lubricated unless their
temperature is
10°F (-12”C), or higher. When the weather is cold, let
them warm up before lubrication or they could be damaged.
Also, be sure to check
all the vehicle fluid levels at this time.
3.
CLUTCH FORK BALL STUD LUBRICATION -Lubricate the clutch fork
ball stud through the fitting on the clutch housing. Lubricant must be
added “sparingly” to the fitting, as only.
0066 Ib. (.003 kg) is required to
lubricate the ball stud surface.
Do not add lubricant more often than the
intervals in the Maintenance Charts.
Too much lubricant will damage
the clutch assembly.
4. ENGINE IDLE SPEED ADJUSTMENT (DIESEL ENGINES)* -Adjust to
the specifications shown on the underhood label. You must use
calibrated test equipment.
5. COOLING SYSTEM SERVICE* -Drain, flush and refill system with new
coolant. See “Engine Coolant’’ in the Index for the proper coolant and
mixture to use in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Tighten all hose clamps (except constant tension \
clamps).
Remove debris and clean the outside
of the radiator and air conditioning
condenser. Wash the radiator neck.
To ensure proper operation, pressure
test the radiator and cap.
* An Emission Control Service
7-1
8
ProCarManuals.com