1993 CHEVROLET ASTRO PASSENGER reset

Downloaded from www.Manualslib.com manuals search engine Windshield Washer
.I
E
K3279
At the top of the multifunction lever there's a paddle with the word PUSH on
it. To spray washer
fluid on the windshield, push and release the paddle. The
wipers will clear the window and then either stop
or return to your preset
speed.
For continued wash operation, press and hold the paddle down.
Driving without washer fluid can be dangerous. A bad mud
/ b splash can block your vision. You could hit another vehicle or go
In freezing weather, don't use your washer until the windshield is\

off the road. Check your washer fluid level often.
warmed. Otherwise the washer fluid can form ice on the
windshield, blocking your vision.
2-33

Downloaded from www.Manualslib.com manuals search engine To Resume a Set Speed
'"
PO431
Suppose you set your Cruise Control at a desired speed and th\
en you apply
the brake. This, of course, shuts
off the Cruise Control. But you don't need
to reset it. Once you're going about 25 mph (40 km/h) or more, you can
move the Cruise switch from
ON to WA (ResumelAccelerate) for about half a
second.
You'll go right back up to your chosen speed and stay there. \
X If you hold the switch at WA (Resume/Accelerate) longer than half a '
, second, the vehicle will keep going faster until you release t\
he switch I or apply the brake. You could be startled and even lose control 90
unless you want to go faster, don't hold the switch at WA
(ResumelAccelerate).
2-37

Downloaded from www.Manualslib.com manuals search engine The digital odometer will read ERROR if someone tries to turn it back.
You may wonder what happens
if your vehicle needs a new odometer
installed.
If the new one can be set to the mileage total of the old odometer,
then it must be. But if it can’t, then it’s set at zer\
o, and a label must be put
on the driver’s door to show the old mileage reading when the \
new odometer
was installed.
Trip Odometer
Standard Cluster Digital Cluster
km/h
t
PO640
The trip odometer can tell you how far your vehicle has been driven since
you last set the trip odometer to zero. Make sure button is completely
depressed.
To reset the trip odometer on the standard cluster, press the but\
ton near the
readout.
The trip odometer on the digital cluster
will appear in place of your regular
odometer when you press the
TRIP button.
To reset the trip odometer on the digital cluster, press the
RESET button. To
change back to the regular odometer, press the
TRIP button again.
Warning Lights, Gauges and Indicators
This part describes the warning lights and gages that are on your vehicle.
The pictures
will help you locate them.
Warning lights and gages can signal that something is wrong before it
becomes serious enough to cause an expensive repair or replacement. Paying
attention to your warning lights and gages could also save you or other\
s from
injury.
2-57

Downloaded from www.Manualslib.com manuals search engine P WR (Power)
The PWR button turns your system on and off.
Pushbuttons
The four pushbuttons let you return to favorite stations. To set the
pushbuttons, just:
1. Tune in the station.
2. Push SET.
3. Within 5 seconds, push one of the four pushbuttons. Whenever you push
that button, the preset station
will return.
Repeat these steps for each pushbutton.
You can preset three more stations by pushing a pair
of buttons next to each
other at the same time. Just:
1. Tune in the station.
2. Push SET.
3. Within 5 seconds, push two buttons next to each other at the same
time. Whenever you push that pair of buttons, the preset stati\
on will return.
Repeat these steps
for each station you select.
CIock
To set the clock, just:
1. Push SET (radio station will be displayed).
2. Within 5 seconds, push and hold HRS (time will be displayed) until the
3. Push and hold MlNS until the correct minute appears.
correct hour appears.
To display the clock with the ignition off, push the upper knob. The time will
be displayed for a few seconds.
3-1 2

Downloaded from www.Manualslib.com manuals search engine Comfort Contmls & Audio Systems
Adjust these levers to give a pleasing sound. If a station is weak and noisy,
move
TREBLE down to reduce the noise.
PWR (Power)
The PWR button turns your system on and off.
Pushbuttons
The four pushbuttons let you return to favorite stations.
You can set the pushbuttons for up
to eight favorite stations (4 AM and
4 FM). Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push one of the four pushbuttons. Whenever you push
that button, the preset station will return.
Repeat these steps for each pushbutton.
You can preset
3 more stations on each band by pushing a pair of buttons
next
to each other at the same time. Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push two buttons next to each other at the same
time. Whenever you push that pair of buttons, the preset stati\
on will return.
Repeat these steps for each pair
of buttons.
Scan Button
When you push this, the radio will go to the next station and stay there a
few seconds. Then
it will go to the next station and pause, and keep doing
that. Press
SCAN again to stop scanning.
Seek Button
This chooses stations also, but it doesn’t keep moving as SCAN does. When
you push
SEEK, the radio goes to the next station and stays there.
Clock
To set the clock, just:
1. Push SET. (SET will be displayed.)
2. Within 5 seconds, push and hold SCAN until the correct hour appears.
3. Press and hold SEEK until the correct minute appears.
To display the clock with the ignition off, push the upper knob. The time will
be displayed for a few seconds.
3-1 4

Downloaded from www.Manualslib.com manuals search engine Comfort Contmls & Audio Systems
Tone Levers
These two levers control the tone of your radio.
BASS-Slide this lever up
to hear more bass.
TREBLE-Slide this lever up
to hear more treble.
Adjust these levers
to give a pleasing sound. If a station is weak and noisy,
move TREBLE down
to reduce the noise.
P WR (Power)
The PWR button turns your system on and off.
DNR@ Button
This is the Dynamic Noise Reduction button. It helps remove background hiss
noise from the radio or tape player. You may want
to leave it pushed in all
the time.
DNR@ is a registered trademark of National Semiconductor Corporation.
Pushbuttons
The four pushbuttons let you return to favorite stations.
You can set the pushbuttons for up to eight favorite stations
(4 AM and
4 FM). Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push one of the four pushbuttons. Whenever you push
that button, the preset station
will return.
Repeat these steps for each pushbutton.
You can preset
3 more stations on each band by pushing a pair of buttons
next
to each other at the same time. Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push two buttons next to each other at the same
time. Whenever you push that pair of buttons, the preset stati\
on will return.
Repeat these steps for each pair of buttons.
Scan Button
When you push this, the radio will go to the next station and stay there a
few seconds. Then
it will go to the next station and pause, and keep doing
that. Press SCAN again
to stop scanning.
3-1 6

Downloaded from www.Manualslib.com manuals search engine Tone Levers (Equalizer)
The 5 levers near the upper knob control the tone of your radio.
Use the levers to set the bass, midrange, and treble until you get th\
e sound
you prefer. The
60 and 250 levers adjust the bass; 1K is midrange; and 3.5K
and 10K adjust the treble.
PWR (Power)
The PWR button turns your system on and off.
Loud Button
Press this for more bass sound; press again to remove it.
AM-ST Button
Push this button if you want AM stereo. (“STEREO’ will be displayed when
you are receiving an
AM stereo station.)
Cr02 Button
The Cr02 button lets you set the system for the type of cassette being used.
If you are using chrome or metal tapes, push the Cr02 button in. If you are
using standard iron tapes, make sure the button is out.
DN@
Your audio system has automatic Dynamic Noise Reduction. It helps remove
background hiss noise from the radio or tape player.
DNR@ is a registered trademark of the National Semiconductor Corporation.
Pushbuitons
The four pushbuttons let you return to favorite stations.
You can set the pushbuttons for up to eight favorite stations
(4 AM and
4 FM). Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push one of the four pushbuttons. Whenever you push
that button, the preset station
will return.
Repeat these steps for each pushbutton.
3-1 9

Downloaded from www.Manualslib.com manuals search engine Comfort Controls & Audio Systems
You can preset 3 more stations on each band by pushing a pair of buttons
next to each other at the same time. Just:
1. Tune in the station.
2. Push SET. (SET will be displayed.)
3. Within 5 seconds, push two buttons next to each other at the same
time. Whenever you push that pair
of buttons, the preset station will
return.
Repeat these steps
for each pair of buttons.
Scan Button
When you push this, the radio will go to the next station an\
d stay there a
few seconds. Then it will go to the next station and pause, and keep doing
that. Press
SCAN again to stop scanning.
Seek Button
This chooses stations also, but it doesn’t keep moving as SCAN does. When
you push
SEEK, the radio goes to the next station
Clock
To set the clock, just:
1. Push SET. (SET will be displayed.)
2. Within 5 seconds, push and hold SCAN until 1 :t-
ahd stays there.
le correct hour appears.
3. Press and hold SEEK until the correct minute appears.
To display the clock with the ignition
off, push the upper knob. The time will
be displayed for a few seconds.
3-20