1993 CADILLAC DEVILLE bulb

Downloaded from www.Manualslib.com manuals search engine f
. ..
:.) ..
Domestic or Export - Remove the two headlamp housing assembly
fasteners.
Domestic or Export - Gently lift the headlamp housing assembly and pull
- it forward to gain access to the bulb and socket housing.

Downloaded from www.Manualslib.com manuals search engine -
ST-
Export - Remove the rubber grommet.
L
Domestic - Remove the wiring harness from the bulb socket.
Connect the wiring harness to the new bulb socket and install into
headlamp assembly.

Downloaded from www.Manualslib.com manuals search engine Export - Remove the retaining spring and raise it up, out of the way.
Export - Reinstall new bulb into headlamp housing assembly, reinstall
rubber grommet and wiring harness.
292
_-

Downloaded from www.Manualslib.com manuals search engine Taillight Bulb Replacement
4. Remove the upper
I and lower tom
1
screws and remove
the bezel.

Downloaded from www.Manualslib.com manuals search engine h
3. Press the bulb
housing lever,
rotate the housing
counterclockwise
1/6 turn and
remove it.
! ..: ’,
5
Y
4. Push and rotate bulb counterclockwise to remove bulb.
Once you have replaced the burned out bulb, just reverse the steps
to
reassemble the taillight.

Downloaded from www.Manualslib.com manuals search engine CENTER HIGH MOUNTED STOP MP
BULB REPUCEMENT
(Sedan Only)
To gain assess to the bulbs, gently pull the back panel located inside the
rear storage compartment.
Turn the socket
1/4 turn to remove it.

Downloaded from www.Manualslib.com manuals search engine 5. Disassemble the
housing assembly
like this.
r-1 push it in and
6. To remove the bulb,
rotate it
counterclockwise.
Once you have replaced the burned out bulb, just reverse the steps to
reassemble the stop lamp assembly.
WIPER BLADE REPUCEMENT
Position the windshield wipers on the windshield in the mid wipe position.
To do this, turn the ignition key to Accessory and turn the wipers on.
Then with the door open, turn the ignition key to off.
th
.-L
c*
300
Start with the driver side wiper blade assembly.

Downloaded from www.Manualslib.com manuals search engine Headlights
The headlight wiring is protected by a circuit breaker in the light switch.
An electrical overload
will cause the lights to go on and off, or in some
cases to remain off.
If this happens, have your headlight wiring checked
right away.
Windshield Wipers
r
The windshield wiper motor is protected by a circuit breaker and a fuse.
If the motor overheats due to heavy snow, etc., the wiper will stop until
the motor cools. If the overload is caused by some electrical problem and
not snow, etc.,
be sure to get it fixed.
I_
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power windows and other
power accessories. When the current load is too heavy, the circuit breaker
-
opens and closes, protecting the circuit until the problem is fixed or goes
away.
BULB CHART
DESCRIPTION BULB NO.
Ash Tray Illumination .................................. 1445
Backup Lights.
........................................ 3057
Center High Mount Stop Light .......................... 1141
CorneringLight ........................................ 881
Courtesy Light
-Doors (White)
....................................... 12864
-Rear Courtesy/Reading
.............................. .562/561
-Doors Warning (Red)
................................. 12864
Courtesy/Maplight
-Without Astroroof
..................................... 906
-With Astroroof
........................................ 56'1
Cruise Control Illumination .............................. 194
Cruise
Control Indicator ................................. 141
ECC Head Illumination .................................. 37
Fuel Data Center Illumination ............................ 194
Glove Compartment Light
............................... 194
Headlights Composite
.-
c-