1992 MAZDA PROTEGE bulb

INTERIOR LAMP SYSTEM T
INTERIOR LAMP SYSTEM
STRUCTURAL VIEW
ZYUU I x-02
1. Spot lamp (in overhead console) 5. IG key illumination
Removal I Inspection / Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-50
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-52 6. Cargo compartment lamp
2. Interior and spot lamp (Without sunroof) Removal I Inspection /
Removal / Inspection I Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-54
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-53 7. Trunk compartment lamp
3. Interior lamp (Without sunroof) Removal I Inspection /
Removal / Inspection / Installation . ..*......................*...... page T-54
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-52 8. Door switch
4. Interior lamp (With sunroof) Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-51
Removal I Inspection / 9. Courtesy lamp
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-53 Removal I Inspection /
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-54
Specifications
Item
Interior and spot lamp
interior lamp
Spot lamp (in overhead console)
Cargo compartment lamp
Trunk compartment lamp
Courtesy lamp Interior
spot Number 1
2
1
2
1
1
2 Specification (W) (Bulb trade number) 10
6
10
8 (67)
5 (168)
5 (168)
5 (168)
23UOTX-028
T-49

INTERIOR LAMP SYSTEM T
IG key illumination does not operate
Check room IOA fuse NG
- Short circuit
0 OK
Confirm battery voltage on V Defective harness (Fuse - Joint box), or bulb
0 OK
Confirm continuity on B wire of the joint box (CPU) to
ground Repair harness (Joint box - Body ground)
OK
When any door is opened, confirm that interior lamp
comes on
OK NG
~ Defective harness (Joint box - Door switch), or door
switch
Confirm continuity between N terminal of JB-09 connec- _ NG
-
tor and B terminal of JB-03 connector Repair harness (JB-09 - JB-03)
I OK
Replace CPU
23UOTX-029
Inspection
Door switch (Front sides with passive belt)
Confirm continuity between the R/W wire and the B wire of
the door switch connector (in passive motor connector).
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
03UOTX-181 Door switch (Others)
Confirm for continuity between the terminals of the door switch.
Condition Continuity
Push X
Not push 0
0: Indicates continuity X: No continuity
1 I OSJOTX-082
T-51

.T INTERIOR LAMP SYSTEM
SPOT LAMP (IN OVERHEAD CONSOLE)
Removal / Inspection / Installation
1. Remove in the order shown in the figure.
2. lnsoect all parts and repair or replace as necessary.
3. Install in the reverse order of removal.
1. Rearview mirror
2. Cover
LENS
3. Lens
4. Bulb
Visual inspection
INTERIOR LAMP (WITHOUT SUNROOF)
Removal / Inspection / Installation
1. Remove the lens.
2. Remove the bulb.
3. Remove the screws and cover.
4. Inspect all parts and repair or replace as necessary.
5. Install in the reverse order of removal.
T-52

INTERIOR LAMP SYSTEM T
COVER
LENS
INTERIOR LAMP (WITH SUNROOF)
Removal / Inspection / Installation
1. Remove the lens.
2. Remove the bulb.
3. Remove the screws and the cover.
4. Inspect all parts and repair or replace as necessary.
5. Install in the reverse order of removal.
ILIVYCA-VI 5
INTERIOR AND SPOT LAMP (WITHOUT SUNROOF)
Removal / Inspection / Installation
1. Remove in the order shown in the figure.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal.
‘- 1. Lens
2. Cover 3. Bulb
Visual inspection
4. Cover
T-53

T INTERIOR LAMP SYSTEM
13UOTX-077 d-------BULB
LENS
T-54
13UOTX-07
23UOTX-0
CARGO COMPARTMENT LAMP
Removal / Inspection / Installation
1. Remove the lens.
2. Remove the bulb.
3. Inspect all parts and repair or replace as necessary.
4. Install in the reverse order of removal.
TRUNK COMPARTMENT LAMP
Removal / Inspection / Installation
1. Remove the lens.
2. Remove the bulb.
3. Inspect all parts and repair or replace as necessary.
4. Install in the reverse order of removal.
COURTESY LAMP
Removal / Inspection / Installation
1. Remove the lens
2. Remove the bulb.
3. Inspect all parts and repair or replace as necessary.
4. Install in the reverse order of removal.

WARNING SYSTEM
Light-off reminder alarm does not sound.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
C Headlight switch Headlight switch ON VB Check headlight switch and
wiring harness
(Refer to pages T-27, 28)
P Ignition switch Ignition switch ON VB Check ignition switch and
wiring harness
(Refer to page T-21)
N Door switch Any door open ov Check door switches and
All doors closed V0 wiring harness
(Refer to page T-51)
23UOTX-033
Seat belt alarm does not sound.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
P ignition switch Ignition switch ON
Vs Check ignition switch and
wiring harness
(Refer to page T-21)
D Seat belt buckle switch Seat belt buckled
00 Check seat belt buckle switch
Seat belt unbuckled
00 and wiring harness
(Refer to page S-102)
23UOTX-034
Seat belt timer does not operate.
VB: Battery voltage
Terminal Connected to Test condition Specification To correct
P Ignition switch Ignition switch ON VE Check ignition switch and
wiring harness
(Refer to page T-21)
23UOTX-035
Passive shoulder belt alarm does not sound.
VB: Battery voltage
Connected to Test condition
Ignition switch Ignition switch Specification
VB
Passive shoulder belt
control unit For 5 seconds after
ignition switch and belt
unbuckled
Other conditions 00
co
IG key illumination timer does not operate.
To correct
I
Check ignition switch and
wiring harness
(Refer to page T-21)
Check passive shoulder belt
control unit and wiring harness
(Refer to page S-104)
23UOTX-036
Ve: Battery voltage
Terminal Connected to Test condition Specification To correct
L IG key illumination Either door open
VB Check bulbs and wiring
harness
N Door switch Any door open ov Check door switches and
All doors closed
VB wiring harness
(Refer to page T-51)
23UOTX-037
T-59

WARNING SYSTEM T
13UOTX-07
63U15X-05
, I//
‘nF -
-
-
FUEL
13UOTX.08C
- CHARGE
13UOTX-08
13UOTX-08
Inspection
Brake system warning lamp
1. Disconnect the connector from the brake fluid level sensor.
2. Connect a jumper wire between “G/Y” and “6” terminal
(body ground).
3. Start the engine and check that the BRAKE warning lamp
illuminates.
Caution
l Be sure that the parking brake is fully released be-
fore checking.
4. If there is no illumination, check the fuse, bulb, and wiring
harness.
Brake fluid level sensor
Connect an ohmmeter to each terminal of the brake fluid lev-
el sensor connector.
Check for continuity when the float is moved up and down.
The sensor is good if there is continuity when the float is be-
low the “MIN” mark, and if there is no continuity when the
float is above the “MAX” mark. If the sensor does not pass
this test, replace it.
Fuel-level warning lamp
1. Disconnect the connector from the fuel tank unit.
2. Connect the connector terminal “W/R” to the body ground.
3. Start the engine and check that the FUEL warning lamp il-
luminates.
4. If there is no illumination, check the fuse, warning lamp, and
wiring harness.
Alternator warning lamp
1. Start the engine, connect the connector terminal “W/B” to
a body ground.
2. Check that the alternator warning lamp illuminates.
3. If there is no illumination, check the warning lamps, wiring
harness and alternator. Replace or repair as necessary.
Engine oil pressure warning lamp
1. Disconnect the connector from the oil pressure switch.
2. Start the engine and connect the connector terminal “Y/R”
to a body ground.
3. Check that the “OIL” warning lamp illuminates. If it does
not, replace the sender switch or repair the wiring harness
if bulb is not burnt out.
T-61

T
I WARNING SYSTEM
Washer fluid warning lamp
1. Disconnect the connector from the washer fluid level sensor.
2. Start the engine and with a jumper wire to connect the con-
nector terminal “a” (LGIW) to a body ground.
3. Check that the washer fluid warning lamp illuminates.
If it does not and the bulb is not burnt out, replace the fluid
level sensor or repair the wiring harness.
13UOTX-08
_-
1 /
J TERMINAL -
13UOTX-08
13UOTX-08
Seat belt warning lamp
1, Remove the CPU.
2. Connect the connector J terminal (joint box side) to a body
ground.
3. Turn ignition switch to ON and confirm that BELT warning
lamp illuminates for about 6 seconds.
4. If there is no illumination, check the fuse, warning readout
and wiring harness.
Check bulb, CPU and wiring harness and switch, repair or
replace as necessary.
Malfunction indicator lamp
1, Connect the “Y/B” wire to a body ground.
2. Start the engine and check that the warning lamp illuminates.
3. If there is no illumination, check the meter fuse, bulb, and
wiring harness between the instrument cluster and the EGI
control unit.
T-62