/ cm-kg, -26-52 In-lb)
(3.8-5.3, 27-M)
Jl TRANSAXLE
INSTALLATION
1. Raise the vehicle and support it with safety stands.
2 Install in the order shown in the figure, referring to Installation Note.
3’ Add the specified amount of the specified transaxle oil. (Refer to page Jl-7.)
4: Warm up the engine and transaxle, and inspect for oil leakage and transaxle operation.
2.4-5.S N.m (30-60
9
1 8-11 N-m
o-110 cm-kg,
* h-95 In-lb)
.O,
cc.
ft-I
03UOJl-119
b)
51-48
03UOJi-12 3
03UOJl-124
L 03UOJl.126 I-
03UOJl-12
Jl TRANSAXLE
Driveshaft
Caution
l Verify that the oil seal is not damaged.
l Do not damage the oil seal
1. Insert the clip with the end-gap at the top of the groove.
2. Apply transaxle oil around the oil seal lip. Install the
driveshaft.
3. Verify that the driveshaft is correctly seated by pulling on
the shaft.
4. Connect the lower arm to the knuckle and tighten the clinch
bolt.
Tightening torque:
43-59 N-m (4.4-6.0 m-kg, 32-43 ft-lb)
Stabilizer (BP SOHC)
1. Tighten the nut until the specified amount of thread is ex-
posed at the end of the bolt.
Dimension A: 17-l 9mm (0.67-0.75 in)
Tie-rod end
1. Install the locknut.
Tightening torque:
42-57 N-m (4.3-5.6 m-kg, 31-42 ft-lb)
2. Secure the locknut with a new cotter pin.
Engine mounting member
1. Install the bolts and nuts as shown.
Tightening torque
@ : 37-52 N,m (3.6-5.3 m-kg, 27-36 ft-lb)
@I: 64-89 N-m (6.5-9.1 m-kg, 47-66 ft-lb)
51-50
TRANSAXLE Jl
03UOJl-12!
03UOJi-13
2. Tighten engine mount No.4 nuts.
Tightening torque:
67-93 N.m (6.6-9.5 m-kg, 49-69 ft-lb)
3. Remove the SST (Engine support).
Control rod and extension bar
1. Install the extension bar to the transaxle.
Tightening torque:
31-46 Nern (3.2-4.7 m-kg, 23-34 ft-lb)
2. Install the change control rod to the transaxle.
Tightening torque:
16-23 N*m (1.6-2.3 m-kg, 12-17 ft-lb)
Ground
1. Connect the ground to the clutch pipe bracket.
Tightening torque:
16-23 N-m (1.6-2.3 m-kg, 12-17 ft-lb)
Speedometer cable
1. Add the specified oil through the speedometer gear case
mounting. (Refer to page Jl-7.)
2. Install the speedometer driven gear.
Tightening torque:
7.6-l 2 N*m (60-120 cm-kg, 69-104 in-lb)
3. Connect the speedometer cable to the speedometer driv-
en gear.
J141
J2 INDEX
IN
new IYLA
BACK-lx LIU, 1, w.., 1 vm q
SERVICE, SECTION
F
k’c’ 1T6AL SWITCH 8.L”
SERI /ICE, SECTION T VISCOSITY: ALL-SEASON ATF DEXRON-II,
M2C33F OR SAE75W-80
ABOVE -18% (OOF) API SERVICE
GL-4 SAE80W-90
CAPACITY: 3.35 liters (3.55 US at. 2.98 ho 41)
1. Transaxle
Removal ..,.....,.,..,....,..,.........,.... page J2-10
Disassembly ,., ,..,., . ,,...., ,.. .., .., page J2-12
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-22
Assembly . . . . . . . . . ,.,...................... page J2-26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-41
52-2
2. Differential
Disassembly / Inspection I
Assembly ,..,.,.,, ,_, ,. .,. ,_. ,_. . . . page J2-44
3. Shift mechanism
Overhaul ,....,.......,..... ,........, . . . . . . page J2-46
4. Transaxle oil
inspection . . . . . . . . ..,........I....I.,..... page J2- 7
Replacement .,.,.., ,.,...,...,.. . . . . . . . . . page J2- 7 .___I’
OUTLINE J2
OUTLINE
SPECIFICATIONS
Item
Transaxle control
Synchromesh system EnginelTransaxle
BP DOHC
GSM-R Floor shift
Forward: Synchromesh
Reverse: Selective sliding and synchromesh
T- I-
Gear ratio
I
1 st 3.307
2nd 1.833
3rd 1.310
4th 1.030
5th 0.795
Reverse 3.166
Final gear ratio 4.105
q
Oil Viscosity All-season
Above -18OC (OOF) ATF DexronYI, M2C33F or SAE75W-80
API service GL-4 SAE80W-90
Capacity liters (US qt, Imp qt) 3.35 (3.55, 2.96)
23UOJ2-001
52-3
