1992 MAZDA PROTEGE lock

FRONT DOOR S
03uosx-01’
PROTEGk 6
f 1.5 (0.24 f 0.06)
HATCHBACK: 6.3
f 1.5 (0.25 f 0.06
mm (in)
Adjustment Note
Door lock striker
1. Verify that the door can be closed easily and that there is
no looseness. If there is a problem, loosen the striker mount-
ing screws and adjust by moving the striker vertically or
laterally.
2. Check the rear offset of the door to the body (or rear door).
If there is a problem, adjust it by moving the door lock striker
laterally.
Tightening torque:
18-28 N-m (1.8-2.7 m-kg, 13-20 ft-lb)
Note
l Use a TORX drive bit for removal/installation of the
door lock striker.
Front door
Loosen the hinge bolts and adjust as shown in the figure. Tight-
en the bolts to the specified torque.
Tightening torque:
18-29 N-m (1.8-3.0 m-kg, 13-22 ft-lb)
s-9

FRONT DOOR LOCK AND OPENER S
FRONTDOORLOCKANDOPENER
COMPONENTS
Removal / Installation
1. Raise the front door glass fully to remove the door lock assembly.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
Note
l Refer to page S-56; Removal of the door mirror for removal of the inner garnish.
1ATCHBACK
1. Regulator handle (Manual regulator) 7. Door screen
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-12 8. Lock control (Power door lock)
2. Inner garnish 9. Front door lock assembly
3. Front door trim (Manual window) 10. Outer handle
4. Front door trim (Power window) 11. Lock cylinder retainer
5. Inner handle 12. Lock cylinder
6. Sealing pad
s-13

S
r
FRONT DOOR LOCK AND OPENER
- 1
PROTEGk
03uosx
1. Regulator handle (Manual regulator)
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
2. Inner garnish
3. Front door trim (Manual window)
4. Front door trim (Power window) 5. Inner handle
6. Sealing pad 7.
Door screen S-12 8.
Lock control (Power door 9.
Front door lock assembly 10.
Outer handle 11.
Lock cylinder retainer 12.
Lock cylinder lock) .-,
S-l 4

REAR DOOR S
REAR DOOR
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
Note
l Remove the rear door trim and door screen for removal of the checker. (Refer to naae S-17.
N-m (m-kg, ft-lb)
1. Harness connector 5. Door lock striker
2. Checker pin Adjustment Note ,..............,.....,.,. page S-16
3. Hinge 6. Checker
4. Rear door
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-i 6
S-l 5

S REAR DOOR
4 f 0.8 (0.16 f 0.03)
OR (FRONT)
-c1 A4 SEC.A-A
mm (in)
03uosx-0’
Adjustment Note
Door lock striker
1. Verify that the door can be closed easily and that there is
no looseness. If there is a problem, loosen the striker mount-
ing screws and adjust by moving the striker vertically or
laterally.
2. Check the rear offset of the door to the body. If there is a
problem, adjust it by moving the door lock striker laterally.
Tightening torque:
18-26 N.m (1.8-2.7 m-kg, 13-20 ft-lb)
Note
l Use a TORX drive bit for removal/installation of the
door lock striker.
Rear door
Loosen the hinge bolts and adjust as shown in the figure. Tight-
en the bolts to the specified torque.
Tightening torque:
18-29 N-m (1.8-3.0 m-kg, 13-22 ft-lb)
S-16

REAR DOOR LOCK AND OPENER S
REAR DOOR LOCK AND OPENER
COMPONENTS
Removal / Installation
1. Raise the rear door glass fully to remove the door lock assembly.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to Removal Note.
4. install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
4.2-6.2 N-m
1, Regulator handle (Manual regulator) 7. Sealing pad
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-l 2 8. Door screen
2. Rear door trim (Power window) 9. Lock knob assembly
3. Rear door trim (Manual window) 10. Lock control (Power door lock)
4. inner handle 11, Rear door lock assembly
5. Pull handle bracket (power window) 12. Outer handle
6. Rear power window switch
s-19

REAR HATCH S
7 f 1.5 (0.28 f 0.06) 6 f 0.8
(0.24 * 0.03)
9 SECA-A R
mm (i..,
03UOSX-02
---i-
----:.
03uosx-oi
Adjustment Note
Rear hatch
Loosen the hinge bolts and adjust as shown in the figure. Tight-
en the bolts to the specified torque.
Tightening torque:
8.8-13 N*m (90-l 30 cm-kg, 78-l 1: in-lb)
Rear hatch striker
Verify that the rear hatch can be closed easily and that there
is no looseness. If there is a problem, adjust the rear hatch
striker.
(1) Loosen the rear hatch striker installation bolts.
(2) Close the rear hatch and align the striker with the rear hatch
lock on the rear hatch.
Tightening torque:
18-23 N*m (1.6-2.3 m-kg, 12-17 ft-lb)
s-21

S REARHATCH LOCKANDOPENER
REARHATCH LOCKANDOPENER
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
2 lnctall in the rpvprs~! order of rwnoval.
2.3, 12-17)
N.m (m-kg, ft-lb
_____-
0.1UOSX-C’
Rear hatch lock Rear hatch opener, opener cable
1. Rear hatch lower trim 5. Trunk end trim
Removal / Installation .,......,,...... page S- 98 Removal / Installation .,,......,,._... page S- 98
2. Lock cylinder retainer 6. Rear hatch striker
3. Lock cylinder assembly Adjustment Note ,.,,,,,,,......,,,,,... page S- 21
4. Rear hatch lock assembly 7. Scuff plate, Trunk side cover, Trunk side trim,
Quarter trim (R.H. side)
Removal / Installation ,.........,..... page S- 98
8. Opener lever
9. Rear seat cushion
Removal / Installation . . . . . . . . . . . . . . . . page S-l 12
10. Rear hatch opener cable
s-22