1992 MAZDA PROTEGE wheel torque

H CLUTCH UNIT
/ 6fs 23UOHX-015
Removal Note
Clutch cover and disc
1. Install the SST or equivalent.
2. Loosen each bolt one turn at a time in a crisscross pattern
until spring tension is released. Then remove the clutch COV-
er and disc.
‘6
I
23UOHX-016
23UOHX-01
Pilot bearing
1. Remove the pilot bearing with the SST if necessary.
Flywheel
Note
l After removing the flywheel, inspect for oil leakage
past the crankshaft rear oil seal.
If necessary, replace the oil seal.
(Refer to Section B.) -J
1. Hold the flywheel with the SST or equivalent.
2. Remove the flywheel.
Installation Note
Flywheel
1. Wipe the bolts clean and apply sealant to the bolt threads.
2. Install the flywheel and the
SST or equivalent.
3. Tighten the bolts in the pattern shown.
Tightening torque:
96-103 N,m (9.6-10.5 m-kg, 71-76 ft-lb)
Pilot bearing
Note
l Install the pilot bearing flush with the flywheel.
1. Install the new bearing with a suitable pipe.
Bearing outer diameter: 35mm (1.376 in) .-’

CLUTCH UNIT, RELEASE BEARING, CLUTCH COVER, CLUTCH DISC H
L
13UOHX-01;
03UOHX-03 8
23UOHX-018
5
03UOHX-032
03UOHX-03
Clutch disc
1. Clean the clutch disc splines and main drive gear splines;
then apply organic molybdenum sulfide grease.
2. Hold the clutch disc in position with the
SST.
Clutch cover
1. Install the SST or equivalent.
2. Align the dowel holes with the flywheel dowels.
3. Tighten the bolts evenly and gradually in the pattern shown.
Tightening torque:
18-26 Nom (1.8-2.7 m-kg, 13-20 ft-lb)
RELEASE BEARING
INSPECTION
Note
l The clutch release bearing Is a sealed bearlng and
must not be washed in solvent.
1. Turn the bearing while applying force in the axial direction.
If the bearing sticks or has excessive resistance, replace it.
CLUTCH COVER
INSPECTION
Note
l Minor scoring or burning should be removed with
emery paper.
1. Inspect the contact surface of the clutch disc for scoring,
cracks, and burning. Repair or replace as necessary.
2. Inspect the contact surface of the clutch release bearing
for wear and cracks.
If there is wear or cracks, replace the clutch cover.
CLUTCH DISC
INSPECTION
Note
l Use sandpaper if the trouble is minor.
1. Inspect the lining surface for burning and oil contamination.
Replace the clutch disc if it is badly burned or oil soaked.
2. Inspect for loose facing rivets and rubbers.
Replace the clutch disc if either is loose.
H-17

TRANSAXLE Jl
1. Transaxle
Installation Note ..,......,.............. page Jl-49
2. Engine mount No.4
3. Driveshaft
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-50
4. Stabilizer (BP SOHC)
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-50
5. Tie-rod end
Installation Note ,........,..,........... page Jl-50
6. Clutch release cylinder
7. Engine mount No.2
8. Exhaust pipe
9. Engine mounting member
Installation Note . . . . . . . . . . . . . . . . . . . . . . . .
page Jl-50
10. Control rod
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-51 11. Extension bar
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-51
1 12. Starter
13. Ground
Installation Note .,..,...,......,........ page Jl-5
14. Neutral switch connector
15. Back-up light switch connector
16. Speedometer cable
Installation Note . . . . . . . . . . . . . . . . . . . . . . . .
page Jl-5
17. Battery carrier
18. Battery
19. Air hose and resonance chamber
20. Splash shield
21. Wheel and tire 1
Installation Note
Transaxle
1. Set the transaxle on a jack and lift it into place.
Install tne transaxle oorts.
Tightening torque:
64-69 N*rn (6.5-9.1 m-kg, 47-66 ft-lb)
Loosely tighten engine mount No.4 bolts.
Jl-49

FRONT AXLE M
WHEEL HUB, STEERING KNUCKLE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Remove the brake caliper assembly and disc plate.
3. Position a dial indicator against the wheel hub. Push and
pull the wheel hub by hand in the axial direction and meas-
ure the wheel bearing play.
4. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
Removal / Installation
d Maximum wheel bearing play: 0.05mm (0.002 in)
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation, check the front wheel alignment. (Refer to Section R.)
SERVIC\E, SECTION R

7 93--12? W.-L%” COTiER PIN, REPLACE
(9.5-12.9, 69-S
39-54
(4.0-5.6, 29-40) 39-64 ’ 236-319 (24.0-32.5, 174-235)
(4.4-6.0, 32-43)
66-67)
N.m (m-kg, it-lb)
23UOMX-006
1. Wheel and tire
2. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6
3. Brake caliper assembly
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
4. Disc plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
5. Tie rod end
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M- 6 6. Lower ball joint
7. Knuckle, wheel hub, and dust cover
Inspect wheel hub for cracks and damage
Inspect knuckle spindle for cracks and
damage
Inspect dust cover for damage and dis-
tortion
Disassembly / Inspection I
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M- 7
M-5

REAR AXLE M
L.3”“I”lh-” I
Removal / Inspection / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation, bleed the brake system, adjust the parking brake lever stroke (Refer to Section P.) and
DRUM BRAKE TYPE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Position a dial indicator against the brake drum. Push and
pull the rear brake assembly by hand in the axial direction
and measure the wheel bearing play.
3. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
Maximum wheel bearing play: 0.05mm (0.002 in)
66-l 17 (6.7-l 1.9, 63-66)
45-59
(4.6:6.0, 33-43)
check the rear wheel alignment (Refer to Section R.)
SEiWICE, SECTION R /
I
GA
19-26 (1.9-2.6, 14-19)
177-235
(16.0-24.0, 130-174) d
REPLACE REPLACE
(9.0-12.0,
65-67)
N.m (m-kg, ft-lb)
7RI ImAX-ni
J 3
1. Wheel and tire
2. Hub cap
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-l 2
4. Brake drum
5. Hub bearing assembly
Inspect for cracks and damage
Disassembly I Assembly . . . . . . . . . . . . page M-l 3 6. Parking brake cable
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P
7. Brake pipe
Removal Note .,.......................... page M-12
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-l 2
8. Rear brake assembly
Service ,,........................................ Section P
9. Rear spindle
Inspect for cracks and damage
M-l 1

M REAR AXLE
DISC BRAKE TYPE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Remove the brake caliper assembly.
3. Position a dial indicator against the wheel hub. Push and
pull the wheel hub by hand in the axial direction and meas-
ure the wheel bearing play.
4. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
-I 5 Maximum wheel bearing play: 0.05mm (0.002 in)
Removal / Inspection / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation. check the rear wheel alianment (Refer to Section R.)
45-61
(4.6-6.2, 33-45)
-118
-12.0,
-87)
REPLACE
16-23
(1.6-2.3, 12-17)
N-m (m-kg, ft-lb]
311 InMY-nif4
1. Wheel and tire
2. Hub cap
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-15
4. Brake caliper assembly
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..~ Section P
5. Disc plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P 6. Hub bearing assembly
Inspect for cracks and damage
Disassembly I Assembly . . . . . . . . . . . . page M-l 5
7. Dust cover
8. Rear spindle
Inspect for cracks and damage
M-14

DRIVE SHAFT M
23UOMX-04
23UOMX-02
I
23UOMX-02
/
I
23UOMX-029
23UOMX-04
Removal note
Tie rod end
Caution
l Do not damage the dust boot.
1. Loosen the nut and disconnect the tie rod end with the SST.
Drive shaft
Caution
l Do not damage the dust cover or oil seal.
1. Remove the drive shaft from the transaxle with a pry bar.
Note
l If the drive shaft is stuck in the front wheel hub, in-
stall a miscellaneous nut until it is flush with the end
of the shaft. Tap the nut with a copper hammer to
remove the drive shaft.
Installation note
Drive shaft
Caution
l Do not damage the dust cover or oil seal.
1. install the drive shaft with the end-gap of clip facing upward.
Tie rod end
Caution
l Do not damage the dust boot.
1, Install the nut and secure it with the new cotter pin.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
M-23

N MANUAL STEERING
03UONX-01:
03UONX-01
23UONX-010
STEERING WHEEL AND COLUMN
On-vehicle inspection
Steering wheel play
With the wheels in the straight-ahead position, gently turn the
steering wheel to the left and right to determine if play is with-
in specification.
Play: O-30mm (O-l. 18 in)
Note
l if play exceeds specification, either the steering
joints are worn or the backlash of the steering gear
is excessive.
Looseness of steering wheel and column
Move the steering wheel in directions @ , @ , and @ to check
for column bearing wear, steering shaft joint play, steering
wheel looseness. and column looseness.
Steering wheel effort
1. With the vehicle on a hard level surface, move the steering
wheel to put the wheels in the straight-ahead position.
2. Attach a pull scale to the outer of the steering wheel, and
then starting with the wheels in the straight-ahead position,
check the steering effort required to turn the steering wheel
to the left and to the right.
3. If the measured effort exceeds specification, check the fol-
lowing: rotation-starting torque of the pinion, rotation torque
of each ball joint, and seizure of each joint.
Steering wheel effort: 108 N (11 kg, 24.2 lb) or less
Note
l Measure after turning the steering wheel to the left
and right 5 times or more.