1992 MAZDA PROTEGE oil capacity

D OIL FILTER, OIL COOLER
r
\/
OSUODX-0
‘I . 03UODX-01
OIL FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface on the
engine.
3. Apply a small amount of clean engine oil to the rubber seal
of the new filter.
4. Install the oil filter and tighten it by hand until the rubber
seal contacts the base.
5. Tighten the filter 1 and 116 turns with a filter wrench.
6. Start the engine and check for leaks.
7. Check the oil level and add oil if necessary.
Oil filter capacity: 0.17 liter (0.18 US qt, 0.15 Imp qt)
OIL COOLER (BP DOHC)
REMOVAL
1. Drain the engine oil.
2. Remove the oil filter with an oil filter wrench.
3. Disconnect the water hoses.
4. Remove the oil cooler.
INSTALLATION
1. Install the oil cooler.
Tightening torque:
29-39 Nnrn (3.0-4.0 m-kg, 22-29 ft-lb)
2. Install the oil filter. (Refer to page D-8.)
3. Add engine oil to the correct level.
4. After installing the filter, check that there is no oil leakage
while the engine is running.
5. Recheck the oil level using the dipstick.
(Refer to page D-7.)

E OUTLINE, TROUBLESHOOTING GUIDE
OUTLINE
SPECIFICATIONS
B6 SOHC
BP SOHC BP DOHC
MTX
1 ATX 1 MTX ATX 1 MTX
ATX
Cooling system
Water-cooled, forced circulation
Coolant capacity liters (US qt, Imp qt) 5.0 6.0
5.0
(5.3, 4.4) (6.3, 5.3)
(5.35.04.4) (6.zi.3) (5.3, 4.4) (6.::.3)
Water
pump
Thermostat
Radiator
Cooling fan
L Type
Water seal Centrifugal
Unified mechanical seal
Type Opening temperature
‘C (OF’) Wax, two-stage
Main: 86.5-89.5 (188-193)
Sub : 83.5-86.5 (182-188)
Full-open temperature
OC (OF)
Full-open lift mm (in)
Type
Cap valve opening
pressure 100 (212)
Main: 8.0 (0.31) min.
Sub : 1.5 (0.06) min.
Corrugated fin
74-103 (0.75-1.05, 11-15)
kPa (kg/cm2, psi)
Width
Core size Height
mm (in)
Depth
Fin pitch
mm (in) 647 (25.47)
390 (15.35)
16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98)
1.3 (0.051)
Heat dissipation capacity
kcallh 1 38,800 [ 43,800 ( 38,800 1 43,800 1 38,800 1 43,800 1
Type
Transaxle Heat
oil cooler dissipation
capacity
kcallh
Tvoe
- Laminated - Laminated -
Laminated
1,700
I .I -?nn
- -
I,,“”
I
I - I 4 Ye,-. I,IVV 1
, a-
- Electric
Number of blades 4
Outer diameter mm (in)
320 (12.6)
Capacity w-v 80-12 1 160-12 ) 80-12 ) 160-12 1 80-12 1 160-12
1 Hi: 13.3+ 1 1 Hi: 13.3+ 1 1 Hi: 13.3+
Current
TROUBLESHOOTING GUIDE I I I I
Problem Possible Cause
Overheating
Coolant level insufficient
Coolant leakage
Radiator fins clogged
Radiator cap malfunction
Cooling fan malfunction
Thermostat malfunction
Water passage clogged
Water puma malfunction .- Remedy Page
Add
Repair
Clean
Replace
Replace
Replace
Clean
Reolace E- 6
E-9
E- 7
E-13
E- 9
E- 6
E-11
I Corrosion
1 Impurities in coolant 1 Replace
I E-6 I
03UOEX-005

OUTLINE F
SPECIFICATIONS
Item
Idle speed*1 *2
Ignition timing*2
Fuel pump
Maximum outout Dressure Engine
rpm B6 SOHC
6O--80 BTDC 1
kPa (ka/cm’. osi1 1 BP SOHC
700-800
4O---6O BP DOHC
90-l 1 O
441-637 (4.5-6.5. 64-92) I
I Fuel filter I
Type Low-pressure side Nylon element (in fuel pump)
High-pressure side Paper element
Pressure reaulator
Regulating pressure kPa (kg/cm’, psi) 1 265-314 (2.7-3.2, 38-46)
I lniector I
Type Type of drive
Resistance
Idle speed control (ISC) valve
TvDe , ,
t Resistance
Purge control solenoid valve
Resistance
Water thermosensor n High-ohmic
Electromechanical
12-16
Rotarv
n I II-13 I
n 1 23-27
1 -20% I -4OFj 1 14.6-17.8
Resistance k62 2ooc i 68OF) 2.21-2.69
40°C (104OF) 1.0-l .3
80°C (176OF) 0.29-0.35
Airflow meter
E2++Vs
E2-Vc Fully closed
Fully open 20-600
20-l ,000
200-400
Capacity liters (US gal, Imp gal) 1 Hatchback 50 (13.2, ll.O), PROTEGE ,... 55 (14.5, 12.1)
I Air cleaner I
Element type
Fuel
Specification l
l Wlth parking brake applied (Canada)
‘2 TEN terminal of diagnosis connector grounded Oil permeated
Unleaded regular (RON 91 or higher) 23UOFX-012
F-l 5

OUTLINE G
OUTLINE
SPECIFICATIONS
Item EnginelTransaxle
‘-2, B6 SOHC BP SOHC BP DOHC
MTX 1 ATX MTX ( ATX
Voltage v 1 12
I
3attery
Dark current*’ Type and capacity
(20-hour rate)
mA 55D23L (60AH) 55D23L (60AH)
Max. 20.0
L\lternator
Starter
Type AC
output V-A 12-65
Regulator type Transistorized (built-in IC regulator)
Regulated voltage V 14.1-14.7
Brush length Standard 21.5 (0.846)
mm (in) Minimum 8.0 (0.315)
Drive belt deflection
New
98 N (10 kg, 22 lb)
mm (in) Used 8-Q (0.31-0.35)
Q-10 (0.35-0.39)
Type
I Direct Direct
I Coaxial
Direct Coaxial
reduction reduction I
output V-kW 12-0.95 12-0.95 12-1.4
12-0.95 12-1.4
Brush length Standard 17 (0.67) 17 (0.67) 17.5 (0.69) 17 (0.67)
17.5 (0.69)
mm (in) Minimum 11.5 (0.453) 11.5 (0.453) 10.0 (0.39) 11.5 (0.453) 10.0 (0.39)
Distributor
Ignition timing BTDC
(TEN terminal of diagnosis connector grounded) Electronic spark advance (photo diode)
6O--8O 4O-6O Q”-1 1 o
Ignition coil
Spark plug Resistance
(at 20% [68OF]) Primary
coil winding 0.81-O.QQg
Secondary
coil winding IO-16 kg
BKR5E-11 BKR5Ell BKR5Ell
NGK
BKR6E-11 BKRGEl 1 BKRGEli
BKR7Ell
Type NIPPON-
DENSON Kl GPR-Ul l
K20PRU 11 KIGPR-Ull
K20PR-Ul l KIGPR-Ull
K20PRUll
K22PR-Ul l
I Plua aao mm (in) I 1.0-l .l (0.039-0.043)
Firing order
’ Dark current is the constant flow of current while the ignition switch is OFF.
(i.e. engine control unit, audio, etc.) l-3-4-2
23lJOGX-00
G-3

Jl INDEX
INDEX
BACK-UP LdHT SWITCH
SERVICE, SECTION T VISCOSITY: SAE 75W-90
CAPACITY : 2.68 liters (2.83 US qt, 2.36 Imp qt)
03UOJl-00
1, Transaxle 2. Differential
Removal.. ..................................
page Jl-IO Disassembly I Inspection I
Disassembly ................................ .............................. page Jl-14 Assembly page Jl-53
Inspection ..................................
page J 1-27 3. Shift mechanism
Assembly .................................. page J l-30 Overhaul ...................................
page Jl-56
Installation ................................. page Jl -48 4. Transaxle oil
Inspection. .................................
page Jl- 7
Replacement ............................. page Jl- 7

OUTLINE Jl
OUTLINE
SPECIFICATIONS
c EnginelTransaxle
B6 SOHC BP SOHC
Item FSM-R
I
Transaxle control
I Floor shift
Synchromesh system Forward: Synchromesh
Reverse: Selective sliding
1 1st
I 3.416
2nd 1.842
I
Gear ratio
4th
Final aear ratio 5th
Reverse I
0.918
0.731
3.214
4.105 3.619
Grade
I API service GL-4
Oil Viscosity
I SAE 75W-90
Capacity liters (US qt, Imp qt) 2.68 (2.83, 2.36)
13UOJl-00
Jl-3

TRANSAXLE OIL Jl
/
03UOJl-00
03UOJl-O(
TRANSAXLE OIL
INSPECTION
Note
l Park the vehicle on level ground.
1. Disconnect the speedometer cable and remove the speedo-
meter driven gear.
2. Verify that the oil level is between the F and L.
3. Install the speedometer driven gear.
Tightening torque:
7.8-12 N,m (80-120 cm-kg, 89-l 04 in-lb)
4. Connect the speedometer cable.
REPLACEMENT
1. Disconnect the speedometer cable and remove the speedo-
meter driven gear.
2. Remove the drain plug and washer. Drain the oil into a suita-
ble container.
3. Install a new washer and the drain plug.
Tightening torque:
39-54 N#rn (4.0-5.5 m-kg, 29-40 ft-lb)
4. Add the necessary amount of the specified oil through the
speedometer driven gear mounting.
Specified oil
Grade: API service GL-4
Viscosity: SAE 75W-90
Capacity: 2.88 liters (2.83 US qt, 2.38 Imp qt)
5. Verify the oil level.
6. Install the speedometer driven gear and connect the
speedometer cable.
Jl-7

J2 INDEX
IN
new IYLA
BACK-lx LIU, 1, w.., 1 vm q
SERVICE, SECTION
F
k’c’ 1T6AL SWITCH 8.L”
SERI /ICE, SECTION T VISCOSITY: ALL-SEASON ATF DEXRON-II,
M2C33F OR SAE75W-80
ABOVE -18% (OOF) API SERVICE
GL-4 SAE80W-90
CAPACITY: 3.35 liters (3.55 US at. 2.98 ho 41)
1. Transaxle
Removal ..,.....,.,..,....,..,.........,.... page J2-10
Disassembly ,., ,..,., . ,,...., ,.. .., .., page J2-12
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-22
Assembly . . . . . . . . . ,.,...................... page J2-26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-41
52-2
2. Differential
Disassembly / Inspection I
Assembly ,..,.,.,, ,_, ,. .,. ,_. ,_. . . . page J2-44
3. Shift mechanism
Overhaul ,....,.......,..... ,........, . . . . . . page J2-46
4. Transaxle oil
inspection . . . . . . . . ..,........I....I.,..... page J2- 7
Replacement .,.,.., ,.,...,...,.. . . . . . . . . . page J2- 7 .___I’