1992 MAZDA PROTEGE diagram

SELF-DIAGNOSIS FUNCTION F
TEP
6
7
8
9
IO
11 INSPECTION
Check for correct fuel line pressure at idle
IV page F-122
Fuel line pressure:
265-314 kPa (2.7-3.2 kg/cm’, 38-46 psi)
(Vacuum hose to pressure regulator
disconnected)
Check intake air system components for air
leakage
Check for misfire of dead cylinder from Step 5
inspection
Check for injector operating sound at idle of
dead cylinder from Step 5 inspection -
Replace injector at dead cylinder from Step 5 in-
spection
CI page F-131
Check if same Code No. is present following
performing after-repair procedure
CT page F-104
Try known good ECU and check if condition
Improves
CT page F-149 Yes
No
Yes If not clogged, check fuel pump
maximum pressure
Go to Step 11
No Replace
--
Yes Repair or replace ignition system
No
Yes
No
Yes
No
T L ACTION
Go to next step
Low pressure
Check fuel line pressure while pinching
fuel return hose
~3 If fuel line pressure quickly in-
creases, check pressure regulator
v page F-129
c3 If fuel line pressure gradually in-
creases, check for clogging be-
tween fuel pump and pressure
regulator
CT page F-126
Go to next step
Go to next step
Check for battery voltage at injector
connector terminal-wire (W/R)
L3 If Yes, replace injector c7 page F-131
+ If No, check wire harness for short
or open
Go to next step
Removed injector at fault
Circuit Diagram
ATX
OXYGENSENSOR
R/L
ECU
-------------- ---
BILG
23UOFX-07
F-10'

SELF-DIAGNOSIS FUNCTION
:ODE No. 1 25 (SOLENOID VALVE - PRESSUREREGULATORCONTROL)-BPENGINE
r (
TEP
1
-
2
-
3 I
INSPECTION
Disconnect connector from ECU and check if
battery voltage exists at ECU terminal 2T (MTX)
3M (ATX) wire (G/O) with ignition switch ON
In same condition as Step 1, check if battery
voltage exists at solenoid valve connector
terminal-wire (G/O) ACTION
Yes Check ECU terminal connector for poor -
connection
* If OK, replace ECU CT page F-149
+
If not OK, repair or replace connector
No Go to next step
Yes Repair or replace wire (G/O)
No Go to next step
Check if solenoid valve is OK Yes Check for short or open circuit in wiring
w page F-135 from main relay (FUEL INJ relay) to
solenoid valve
No Replace solenoid valve
I I I
23UOFX-077
:ODE No. 26 (SOLENOID VALVE - PURGE CONTROL)
STEP INSPECTION
Disconnect connector from ECU and check if
battery voltage exists at ECU terminal 2X (MTX)
20 (ATX) wire harness (W/L) with ignition switch
ON Yes
No
In same condition as Step 1, check if battery
Yes
voltage exists at solenoid valve connector
terminal-wire (W/L)
No
Check if solenoid valve is OK
Yes
w page F-140
t- No
--
4 ACTION
Check ECU terminal connector for poor
connection
ti If OK, replace ECU c;p page F-149
e
If not OK, repair or replace connector
Go to next step
Repair or replace wire harness (W/L)
Go to next step
Check for short or open circuit in wiring
from main relay (FUEL INJ relay) to
Circuit Diagram
MTX
I-
FROM
BATTERY
FROM
23UOFX-07 9
F-l 02

SELF-DIAGNOSIS FUNCTION F
1
CODE No. 34 (ISC VALVE)
1 ACTION
Yes Check ECU terminal connector for poor
connection INSPECTION
Disconnect connector from ECU and check if
battery voltage exists at ECU terminal 2W (MTX)
3Q (ATX) wire (L/O) with ignition switch ON
c3 If OK, replace ECU
+ If not OK, repair or replace con-
nector w page F-149
No Go to next step
In same condition as Step 1, check if battery
voltage exists at ISC valve connector terminal.
wire (L/O) Yes ) Repair or replace wire (L/O)
No Go to next step
Yes Check for short or open circuit in wiring
from main relay (FUEL INJ relay) to ISC
valve
No Replace ISC valve Check ISC valve for correct resistance
w page F-i 16
Resistance: 1 l-130 [at 20°C(68”F) ]
I 23UOFX-08( I
r C :ODE No. )
41 (SOLENOID VALVE - VICSbDOHC
I
ii
T
I
INSPECTION
ACTION
Check ECU terminal connector for poor
connection
in’
I
* If OK, replace ECU w page F-149
c3 If not OK, repair or replace con-
nector
No Go to next step Disconnect connector from ECU and check if
battery voltage exists at ECU
terminal 2S (MTX)
31 (ATX) wire (B/R) with ignition switch ON
2 In same condition as Step 1, check if battery voltage exists at solenoid valve connector
terminal-wire (B/R)
Check if solenoid valve is OK
w page F-l 18 Yes Repair or replace wire (B/R)
No Go to next step
Yes Check for short or open circuit in wiring
from main relay to solenoid valve
No
Replace solenoid valve
23UOFX-081 3
Circuit Diagram
ATX
ISC VALVE
FROM
BATTERY 4
FROM
L
IGNITION d++n.D,,
SWITCH
MAIN RELAY
(FUEL INJ RELAY) S
4\ ECU
SOLENOID VALVE
i(VICS) [DOHC]
W/R ,,
\
SOLENOID VALVE ,
(PURGE CONTROL)
23UOFX-082
F-i 03

G
ENGINE ELECTRICAL SYSTEM
INDEX ......................................................
OUTLINE ..................................................
SPECIFICATIONS .................................... G- 3
TROUBLESHOOTING
GUIDE.. .................... G-
4
DIAGNOSTIC INDEX ................................
SYMPTOM TROUBLESHOOTING..
............. :- t
-
CHARGING SYSTEM ................................. G- 6
PREPARATION .......................................
CIRCUIT DIAGRAM ................................. :I ;
TROUBLESHOOTING .............................. G- 7
BATTERY ............................................... G- 6
ALTERNATOR ........................................ G-10
DRIVE BELT ........................................... G-14
IGNITION SYSTEM .................................... G-15
PREPARATION ....................................... G-15
CIRCUIT DIAGRAM ................................. G-15
TROUBLESHOOTING .............................. G-16
IGNITION TIMING ................................... G-17
HIGH-TENSION LEAD .............................. G-17
SPARK PLUGS ....................................... G-16
IGNITION COIL ....................................... G-19
DISTRIBUTOR ........................................ G-20
IGNITER ................................................ G-23
STARTING SYSTEM .................................. G-24
PREPARATION ....................................... G-24
CIRCUIT DIAGRAM ................................. G-24
STARTER ...............................................
G-25
STARTER INTERLOCK SWITCH (MTX)
........ G-31
03UOGX-001

G CHARGING SYSTEM
03UOGX-011
CIRCUIT DIAGRAM
CHARGING SYSTEM
PREPARATION
SST
I I
49 9200 020
Tension gauge,
V-ribbed belt For
inspection of
drive belt tension
STATOR
1 DIODE TRIO
T l-f-l /
-I J
WARNING
t
I --.- I I I I 15A
e I
I I -L
-E-
I IC REGULATOR
0
-
BATTERY = IGNITION
SWITCH
03u0tix-012
The alternator has a self-diagnostic function to warn of the following
If a problem arises, the alternator warning lamp illuminates. problems in the charging system.
1. S terminal circtiit open
2. No voltage output
3. Field coil circuit open
4. B terminal circuit open
5. Voltage output too high
G-6

IGNITION SYSTEM G
IGNITION SYSTEM
PREPARATION
SST
49 NO18 001
Adapter Harness
CIRCUIT DIAGRAM
ECU
T
IGNITION SWITCH
,
I
DISTRIBUTOR
7
1 ZL BATTERY
IGNITER
03UOGX-03t
G-15

G STARTING SYSTEM
STARTING SYSTEM
PREPARATION
SST
49 E301 144
Removing plate
I I 03UOGX-062
CIRCUIT DIAGRAM
I --II /l--f--I1 I It------t--r/
INHIBITER SWITCH-ATX 1 It---f-l/
SWITCH STARTER IF
SWFCH-MTX
II
BATTERY V 0
FIELD COIL
BRUSH
S TERMIN
M TERMINAL
““““.“I “1 Note
l BP ATX vehicles use a coaxial reduction starter.
G-24

POWER DOOR LOCK SYSTEM
TROUBLESHOOTING GUIDE
Circuit Diagram
l POWER DOOR LOCK K-2
MAIN
c-09 POWER DOOR LOCK SWITCH(OR1) K--IO POWER DOOR LOCK K-II POWER DOOR LOCK MOT(X?FP
RELAY (F)
(3HB) (PROTEGE)
(3HB) (PROTEGE)
C-12 POWER DOOR LOCK K-13 POWER OOOR LOCK
MOTOR RL (OR31 MOTOR RR (OR41
S-24