1992 MAZDA PROTEGE air condition

U
COOLING UNIT
Removal / Installation AIR CONDITIONER
1. Discharge the refrigeration system. (Refer to page U-32.)
2. Remove the glove box, glove box cover, undercover, and instrument panel stay. (Refer to Section S.)
3. Remove the cooling unit as shown in the figure. -
Note
l Immediately plug all open fittings to keep moisture out of system.
4. Install the cooling unit in the reverse order of removal.
Note
l Position the cooling unit so that its connections match those of the heater unit and blower unit.
l Apply clean compressor oil to the O-rings before connecting the fittings.
l Do not apply compressor oil to the fitting nuts.
l When installing a new cooling unit, add compressor oil through the high-pressure pipe port
of the compressor.
Compressor oil: 50 cc (3.05 cu in)
Tightening torque
Outlet pipe: 20-29 N*m (2.0-3.0 m-kg, 14-22 ft-lb)
lnla+ nina. Q n,7n N.m (I -0-2.0 m&a. 7,7-IA ftJh IIllcvb yap”. “.” -1 . . . . . \..’ -_- __- ..~, JII .- .I .-,
23UOUX-0: -.,
1. Cooling unit
Disassembly / Assembly.. . . . . . . . . . . . page U-39
U-38

AIR CONDITIONER U
Dlsassembly / Assembly
Disassemble and assemble as shown in the figure.
1. Evaporator 2. Expansion valve 3. Thermoswitch
Replacement
Expansion valve
Note
l Before replacement of the expansion valve, care-
fully check the refrigeration system, referring to the
troubleshooting information on page U-14.
1. Remove the cooling unit. (Refer to page U-38.)
2. Disassemble the cooling unit. Remove the evaporator and
expansion valve as an assembly.
3. Disconnect the inlet and outlet pipes.
I 4. Remove the capillary tube from the outlet pipe and remove
23UOUX-024 the expansion valve.
5. Install in the reverse order of removal, noting the following.
Note
l Apply clean compressor oil to the O-rings before
connecting the fittings.
Tightening torque
Inlet pipe:
12-15 N-m (1.2-l .5 m-kg, 8.7-l 1 ft-lb)
Outlet pipe:
29-34 Nmrn (3.0-3.5 m-kg, 22-25 ft-lb)
u-39

U AIR CONDITIONER
OFF
03UOUX-06
03UOUX-06,
03UOUX-06
On-vehicle Inspection
Thermoswitch
1. Remove the glove box.
2. Run the engine at idle.
3. Turn OFF the A/C switch and set the blower switch to the
highest position to operate the blower fan for a few minutes.
4. After a few minutes, turn OFF the blower switch and stop
the engine.
5. Disconnect the thermoswitch connector and check for con-
tinuity between terminals of the switch.
Terminals Continuity
a-b Yes
6. If not as specified, replace the thermoswitch.
Note
l The thermoswitch contacts will be open if the
evaporator temperature is below 0.4 f 0.7OC (32.7
z!z 1.3OF).
Inspection
Thermoswitch
1. Immerse the sensing bulb in a container of ice water.
2. Check continuity between terminals of the switch as
specified.
Terminals
a-b Temperature Continuity
Above 5°C Yes
Below 0% No
3. If not as specified, replace the thermoswitch
Evaporator
1. Check the evaporator fins for blockage. If the fins are
clogged, clean them with compressed air.
Caution
l Never use water to clean the evaporator.
2. Check the fittings for cracks and other damage.
Replace the evaporator if necessary.
u-40

AIR CONDITIONER U
COMPRESSOR
Removal / Installation
1. Discharge the refrigeration system. (Refer to page U-32.)
2. Remove the undercover.
3. Remove the compressor as shown in the figure, referring to
Removal Note.
4. Install the compressor in the reverse order of removal, referring to Installation Note.
5. Install the undercover.
6. Charge the refrigeration system. (Refer to page U-33.)
u
24-35 (2.4-3.6, 17-26)
N.m (m-kg, ft-it
23UOUX-0
1. Suction hose
2. Discharge hose 3. Compressor
Note
l Immediately plug any open fittings to keep moisture out of the system.
l Apply new compressor oil to the O-rings before connecting the fittings.
l Do not apply compressor oil to the fittings.
l Tightening torque Compressor inlet and outlet: 9.8-l 8 N.m (1.0-l .8 m-kg, 8-l 2 ft-lb)
l Adjust the belt tension to specification.
lb-41

U AIR CONDITIONER
-0
1 03UOUX-066
23UOUX-02 16
1 13UOUX-027
.ECTION
Removal note
Drive belt
Remove the drive belt as follows.
Vehicle with power steering.
1) Loosen bolt A.
2) Loosen nut C.
3) Loosen nut B.
4) Loosen bolt D.
5) Remove the drive belt.
Vehicle without power steering
1) Loosen nut A.
2) Loosen bolt B.
3) Remove the drive belt.
Installation note
Vehicle with power steering
Drive belt
Adjust the deflection of the drive belt as follows.
Vehicle with power steering
1) Loosen bolt A and nuts B and C.
2) Turn adjusting bolt B and adjust the deflection of the drive
belt to within specification.
Belt Deflection: When applying moderate pressure 98 N (IO kg, 22 lb)
New 8-Qmm (0.31-0.35 in)
Used Q-IOmm (0.35-0.39 in)
3) Tighten bolt A and nuts B and C.
Tightening torque
Bolt A: 36-54 N.m (3.7-5.5 m-kg, 27-40 ft-lb)
Nut B : 19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
Nut C : 32-46 N,m (3.2-4.7 m-kg, 24-34 ft-lb)
Vehicle without power steering
1) Loosen nut A.
2) Turn adjusting bolt B and adjust the deflection of the drive
belt to within specification.
Belt Deflection: When applying moderate pressure 98 N (10 kg, 22 lb)
New 8-Qmm (0.31-0.35 in)
Used Q-10mm (0.35-0.39 in)
3) Tighten nut A. Tightening torque
Nut A: 31-34 N.m (3.2-3.6 m-kg, 23-25 ft-lb)
U-42

AIR CONDITIONER U
Disassembly / Assembly
Preparation
SST
49 B061 005
Replacer,
seal plate For
replacement of
shaft seal plate 0000-4 l-0809-06
Remover &
installer, seal For
replacement of
shaft seal
03uoux-07
Structural view
I
1. Compressor body 4. Discharge valve body 6. Discharge valve plate
2. Shaft seal plate 5. Thermal protector 7. Discharge valve
3. Shaft seal
u-43

U AIR CONDITIONER
23UOUX-02
Thermal Protector Replacement
1. Removal of discharge valve body
Remove the bolts and carefully remove the discharge valve
body. .-
2. Removal of snap ring and thermal protector
Note
l When removing the thermal protector, do not pull
the harness wires but push the protector out from
its back side.
23UOUX-028 3. Installation of thermal protector
1) Check that the O-ring groove is free from foreign matter.
Apply compressor oil to the O-ring and properly fit it in
the groove.
2) Before installing the thermal protector, check it for con-
tinuity.
23uoux-029 _/”

THERMAL PROTECTOR
23UOUX-03
TH
PR
3) Install the snap ring so that its chamfered edge side faces
the thermal protector (the non-chamfered side faces out-
ward) as shown left.
Make sure the snap ring is seated securely in its groove.
Note
l Install the thermal protector so that its two lead wire
outlet sections are horizontal as shown left.

AIR CONDITIONER U
23UOUX-031 DISCHARGE
VALVE BODY
CYLINDER
1
23UOUX-03
4. Installation of discharge valve body
1) Replace the O-ring and gasket with new ones.
Apply compressor oil to the new O-ring and gasket and
properly assemble them.
Note
l Fit the gasket as shown left while checking that its
top side faces upward.
2) Carefully install the discharge valve body on the com-
pressor and finger tighten the six M6 bolts.
Note
Bolt torquing sequence
l Torque the two socket head bolts (A) to the specifi-
cation.
l Torque the four bolts (B) in a diagonal manner to
the specification.
Tightening torgue: 9.8 N,rn (100 cm-kg, 87 in-lb)
u-45