1992 MAZDA PROTEGE F 149

B2 INSPECTION / REPAIR
r--
1
05UOBX-14
I -
L
05UOBX-149
82-60
(8) Measure the oil clearances.
Oil clearance:
0.035-0.081 mm (0.0014-0.0032 in)
Maximum: 0.15mm (0.006 in)
(9) If the oil clearance exceeds specification, replace the
cylinder head.
7. Measure the camshaft end play. If the end play exceeds
specification, replace the camshaft and/or the cylinder head.
End play : 0.07-0.19mm (0.0028-0.0075 in)
Maximum: 0.20mm (0.008 in)
HLA
Caution
l Do not attempt to repair the HLA.
1, Inspect the HLA friction surfaces for wear or damage. Re-
place the HLA if necessary.
2. Hold the bucket body and press the plunger by hand. If
the plunger moves, replace the HLA.
CYLINDER BLOCK
1. Inspect the cylinder block for the following. Repair or re-
place the cylinder block as necessary.
(1) ‘Leakage damage.
(2) Cracks.
(3j Scoring of wall.
2. Measure the distortion of the top surface of the cylinder block
in the six directions shown in the figure.
Distortion: 0.15mm (0.006 in) max.
3. If the distortion exceeds specification, repair by grinding’or
replace the cylinder block.
Height : 221 Smm (8.720 in)
Grinding: 0.20mm (0.008 in) max.

F
FUEL AND EMISSION
CONTROL SYSTEM
INDEX ...........................................
OUTLINE ...................................... ;: 2
SYSTEM DIAGRAM ...................... F-
:
VACUUM HOSE ROUTING
DIAGRAM .................................
WIRING DIAGRAM ....................... F- 6
- 7
ENGINE CONTROL UNIT (ATX) ...... F- 13
SPECIFICATIONS.. ....................... F- 15
COMPONENT DESCRIPTIONS.
...... F- 16
TROUBLESHOOTING GUIDE.. ......... F- 20
ENGINE CONTROL OPERATION
CHART
..................................... F- 20
RELATIONSHIP CHART.. .............. F- 24
USING THIS SECTION .................. F- 25
DIAGNOSTIC INDEX .................... F- 27
PRECAUTION ............................. F- 29
SYMPTOM TROUBLESHOOTING .... F- 30
ENGINE TUNE-UP
.......................... F- 76
PREPARATION ............................
F- 76
BASIC INSPECTION ..................... F- 78
ADJUSTMENT .............................
F- 79
SELF-DIAGNOSIS FUNCTION .......... F- 82
DESCRIPTION .............................
F- 82
PREPARATION
............................
F- 83
SERVISE CODE NUMBER.. ........... F- 83
SWITCH MONITOR FUNCTION ...... F-105
INTAKE AIR SYSTEM.. ................... F-109
COMPONENT PARTS.. ................. F-109
THROTTLE BODY ........................ F-l 12
DYNAMIC CHAMBER ................... F-l 12
INTAKE MANIFOLD ..................... F-l 13
ACCELERATOR PEDAL ................ F-l 14
ACCELERATOR CABLE ................ F-l 14
IDLE SPEED CONTROL (ISC)
SYSTEM ......................................
F-115
DESCRIPTION ............................. F-115
PREPARATION
............................ F-116
SYSTEM OPERATION.. ................. F-l 16
ISC VALVE ................................. F-116
AIR VALVE
................................. F-116
VARIABLE INERTIA CHARGING
SYSTEM (VICS) [DOHC] ................ F-l 17
DESCRIPTION ............................. F-117
SYSTEM OPERATION ................... F-l 18
SHUTTER VALVE ACTUATOR.. ...... F-l 18
SOLENOID VALVE (VICS). ............. F-118
VACUUM CHAMBER.. .................. F-119
FUELSYSTEM .............................. F-l 20
DESCRIPTION
............................. F-l 20
PRECAUTION ............................. F-121
SYSTEM OPERATION.. ................. F-121
FUEL TANK ................................
F-l 23
FUEL FILTER .............................. F-l 24 FUEL PUMP ............................... F-l 25
CIRCUIT OPENING RELAY.. .......... F-129
PRESSURE REGULATOR.. ............ F-129
INJECTOR .................................. F-l 31
PRESSURE REGULATOR
CONTROL SYSTEM.. .................... F-l 34
SOLENOID VALVE (PRESSURE
REGULATOR CONTROL). ............ F-l 35
EXHAUST SYSTEM ........................ F-l 36
COMPONENT PARTS.. ................. F-136
OUTLINE OF EMISSION
CONTROL SYSTEM.. .................... F-l 37
STRUCTURAL VIEW.. ................... F-l 37
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM.. ..... F-138
DESCRIPTION .............................
F-l 38
PCV VALVE ................................ F-l 38
EVAPORATIVE EMISSION
CONTROL SYSTEM.. .................... F-l 39
DESCRIPTION ............................. F-l 39
SYSTEM OPERATION.. ................. F-140
SOLENOID VALVE
(PURGE CONTROL) ................... F-140
SEPARATOR ............................... F-l 40
CHECK VALVE (TWO-WAY) ........... F-140
CHECK-AND-CUT VALVE.. ............ F-141
CHARCOAL CANISTER.. ............... F-141
DECELERATION CONTROL
SYSTEM ...................................... F-l 42
DESCRIPTION ............................. F-l 42
DASHPOT .................................. F-142
FUEL CUT CONTROL SYSTEM ....... F-143
DESCRIPTION ............................. F-l 43
PREPARATION ............................ F-l 43
SYSTEM OPERATION.. ................. F-143
DECHOKE CONTROL SYSTEM.. ...... F-145
DESCRIPTION ............................. F-l 45
SYSTEM OPERATION ................... F-l 45
CONTROL SYSTEM ....................... F-l 47
PREPARATION ............................ F-147
STRUCTURAL VIEW.. ................... F-l 48
ENGINE CONTROL UNIT (ECU) ..... F-149
AIRFLOW METER (WITH INTAKE AIR
THERMOSENSOR) ..................... F-168
WATER THERMOSENSOR.. ........... F-168
THROTTLE SENSOR .................... F-l 69
OXYGEN SENSOR.. ..................... F-171
MAIN RELAY (FUEL INJ RELAY) .... F-172
CLUTCH SWITCH (MTX) ............... F-172
NEUTRAL SWITCH (MTX). ............. F-173
POWER STEERING PRESSURE
SWITCH .................................... F-173
WJOFX-001

INDEX F
1. Resonance duct
Inspection / Replacement.. ........ page F-l 09
2. Air cleaner element
Inspection ................................. page F- 79
Replacement.. ........................... page F-l 09
3. Airflow meter
(With intake air thermosensor)
Inspection
................................. page F-l 68
Replacement.. ........................... page F-l 09
4. Resonance chamber
Inspection I Replacement.. ........ page F-l 09
5. Throttle body
Inspection .................................
page F-l 12
Replacement.. ...........................
page F-l 09
6. Throttle sensor
inspection ................................. page F-l 69
Adjustment..
.............................. page F-l 69
Replacement.. ........................... page F-l 71
7. ISC valve
Inspection ................................. page F-l 16
Replacement..
........................... page F-l 09
8. Dashpot
Inspection ................................. page F-l 42
9. Dynamic chamber
Removal / Installation ................
page F-109
Inspection [DOHC] ................... page F-l 12
10. Air valve
Inspection
................................. page F-l 16
Removal / Installation ................ page F-109
11. Shutter valve actuator
Inspection ................................. page F-l 18
12. Vacuum chamber [DOHC]
Inspection ................................. page F-l 19
13. Intake manifold
Removal / Installation ................ page F-l 09
14. Injector
Inspection .................................
page F-l 31
Removal .................................... page F-131
Installation.. ............................... page F-l 33 15. Pressure regulator
Inspection ................................. page F-l 29
Replacement ............................. page F-l 30
16. Solenoid valve (Pressure regulator control)
[BP1
Inspection ................................. page F-l 35
17. Solenoid valve (VICS) [DOHC]
Inspection ................................. page F-l 18
18. Charcoal canister
Inspection ................................. page F-l 41
19. Solenoid valve (Purge control)
Inspection ................................. page F-l 40
20. Circuit opening relay
Inspection ................................. page F-l 29
Replacement ............................. page F-l 29
21. Engine control unit (ECU)
Removal / Installation ................ page F-l 49
Inspection ................................. page F-149
22. Clutch switch (MTX)
Inspection ................................. page F-l 72
Replacement.. ........................... page F-l 72
23. PCV valve
Inspection ................................. page F-l 38
24. Water thermosensor
Removal / Inspection /
Installation ............................... page F-l 68
25. Fuel filter (High-pressure side)
Replacement.. ........................... page F-l 24
26. Main relay (FUEL INJ relay)
Inspection ................................. page F-l 72
27. Neutral switch (MTX)
inspection ................................. page F-l 73
Replacement.. ........................... page F-l 73
28. Oxygen sensor
Inspection ................................. page F-l 71
Replacement ............................. page F-l 72
29. Power steering pressure switch
Inspection ................................. page F-l 73
Replacement.. ........................... page F-l 73
23UOFX-002
F-3

F TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
ENGINE CONTROL OPERATION CHART
Note
Input Device and Engine Conditions
l The data in this chart is for reference only.
INPUT DEVICES APPROX,- SENSORS
MATE TIME G& THROTTLE SENSOR
(BASED ON TRIBUTOR
WATER INTAKE
10-16°C, (G. OXYGEN AIRFLOW AIR
VT
POW
.50-6OOF
SIGNAL)” ;;;;;f- SENSOR METER
AMBIENT) (Ne-SIGNAL) THERMO- TERMINAL TERMINAL yE\MINAL
CONDITIONS SENSOR (ATX)
WX)
A
c
CRANKING
-COLD ENGINE Signal has Signal has Signal has Signal has Slgnal has Slgnal has
l COLD AIR zero no affect no effect no effect no effect no effect
no effect
. COLD COOLANT on ECU on ECU on ECU on ECU on ECU
on ECU
Cool to A A
COLD START
warm: Low volume Closed Closed
Closed
-FAST IDLE
One
Medium airflow: throttle: throttle:
l COLD AIR
minute
voltage High volt-
Low volt- Low volt- throttle.
Low volt-
* COLD COOLANT
(3.5” and :zo:o, ,,Pbove 1’,“,“$; a(ogi-O,8”) ;149&“) we W)
dropping) to high
(68OF)]:
COLD DRIVEAWAY voltage A
Above
-PART THROTTLE Two (O-0.9”) 2.3”
l COLD AIR minutes
l COLD COOLANT
v v ,,
Warm: Medi- Sensor Moderate II
WARM DRIVEAWAY
volume air-
-PART THROTTLE Three N&IGNAL um voitage hot:
flow: Low
l WARM AIR minutes Sends all Vvwrox switching l WARM COOLANT cylinders 0.7V and
from high to medium
Part Part
TDC signal dropping) voltage voltage
throttle: throttle.
)
A (0.9V) (1 .o-3.5”)
to ECU
.“~ Medium Medium
HOT CRUISE
s voltage voltage
Open
l WARM AIR G-
SIGNAL”’ to low (0.8-3.0”) (4.5-5.5”) throttle:
l WARM COOLANT High
Sends No. voltage
1 cylinder (0.1”) voltage
1 (battery
TDC (com-
1 I voltage)
HOT ACCELERATION pression)
-60% THROTTLE signal to
Moderate
ECU
to strong
High Cool lo warm
voltage ;$,“,” Of j-20-4OT
f t
HOT ACCELERATION
More’ than Hot: Low (0.9”) Low (-4-‘04”F)l: W,ds open
voltage 1.5-4.3v
throttle: Wide open
-WIDE OPEN
four voltage
High volt- throttle
THROTTLE (0.5-1.5V)
minutes (Below High
0.5”) age (Above
voltage (OV)
t 1 3.OV)
I,
A 1. /I
DECELERATION
-CLOSED THROTTLE
HOT CURB IDLE
-EXTENDED
HOT ENGINE
SHUTDOWN Low
voltage
(0”) Low Closed Closed
Closed
volume throttle: throttle.
throttle.
of airflow:
~~~~!$$ (Above Low Low
Low
voltage voltage
voltage
to low 3.OV) (0.2-0.N) (4.5-5 5V) (OV)
voltage
(0.75%
t t 1 0.25”)
r v 1 I I
Sensor
hot: Low
OFF OFF voltage
-
(0.1”) until OFF OFF OFF OFF
OFF
sensw
COOIS
._-

F TROUBLESHOOTING GUIDE
SYMPTOM TROUBLESHOOTING
2 CRANKS NORMALLY BUT WILL NOT START (NO COMBUSTION)
l Engine cranks at normal speed but shows no sign of “firing”
DESCRIP-
*Battery in normal condition
TION
*Throttle valve not held fully open while cranking (Dechoke system not operate)
*Fuel in tank [TROUBLESHOOTING HINTS]
Because of no combustion, possibly no fuel is injected to engine or no ignition at all cylinders
:I) No spark
@I Low fuel line pressure
l Ignition control malfunction
@ Low engine compression l Ignition system component malfunction
3 No fuel injection
l Fuel pump inoperative l Injectors inoperative
TEP INSPECTION
ACTION
1 Check if strong blue spark is visible at discon-
Yes Go to Step 3
netted high-tension lead
No Go to Step 2
2 Check if “00” is displayed on Self-Diagnosis
Yes Check ignition system (Refer to
Checker with ignition switch ON
Troubleshooting “Misfire”) w page G-5
w page F-82
No Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-83
“88” flashes
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST e If OK, replace ECU w page F-149 c3 If not OK, check wiring between
SELECT SW: A ECU and Self-Diagnosis Checker
3 Connect diagnosis connector terminals F/P and
Yes Check if engine starts in this condition
GND with jumper wire and check for fuel pump
operating sound with ignition switch ON c3 If starts, check circuit opening relay c7 page F-129
w page F-125
c3 If does not start, go to Step 5
DIAGNOSIS C
Go to next step ._-,
._. ,
F-30

TROUBLESHOOTING GUIDE F
w page F-125
tor (W/R) wire with ignition switch ON
MTX...lN, 2A, 2U, 2V
ATX... IT, 3A, 3U, 3V w page F-150
w page F-172
Fuel Line pressure:
265-314 kPa (2.7-3.2 kg/cm2, 36-46 psi)
fuel return hose w page F-129
fuel return hose is clogged or w page F-120
CT page F-130
(6.5 kg/cm2, 121 psi)-300 rpm
(9.0 kg/cm2, 128 psi)300 rpm
l Defective cylinder head gasket l Distorted cylinder head
WEAR AND C
AMAGE AND
ETERIORATION CT- page F-149
F-31

F TROUBLESHOOTING GUIDE
3 CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) - WHEN ENGINE COLD
DESCRIP- *Engine cranks at normal speed but shows only partial combustion and will not continue to run
TION
l Battery in normal condition
*Fuel in tank
[TROUBLESHOOTING HINTS]
0 Air/Fuel mixture too rich
*Air cleaner element clogged
l Airflow meter stuck @ Low engine compression
@ Air/Fuel mixture too lean
l Fuel injection control malfunction
(Correction for coolant temperature)
*Low fuel line pressure
*Air leakage of intake air system
Checker with ignition switch ON
CT page F-83
w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST w page F-149
Fuel line pressure:
285-314 kPa (2.7-3.2 kg/cm’, 38-48 psi) If fuel line pressure quickly in-
creases, check pressure regulator CF- page F-129
d If fuel line pressure gradually in-
creases check for clogging be-
I pump and pressure
Check if fuel return hose is clogged or
F-32

TROUBLESHOOTING GUIDE
TEP INSPECTION ACTION
4 Check if ECU terminal voltages are OK Yes Go to next step
MTX...Especially IC, 20 and 2Q
ATX... Especially lC, 2E and 3D v page F-150
No Check for cause ~3‘ page F-151
5
Check for air leakage of intake air system com- Yes Repair or replace
ponents
No Go to next step
6 Check if engine starts when water thermosensor Yes Check water thermosensor c7 page F-158 is disconnected
Check for correct engine compression 82-10 ’ No
Check engine condition CIP page Bl-10
Engine compression: 82-10
l BP SOHC l Worn piston, piston rings or cylinder 834 kPa (8.5 kg/cm*, 121 psi)300 rpm
wall
l BP DOHC l Defective cylinder head gasket 883 kPa (9.0 kg/cm*, 128 psi)-300 rpm l Distorted cylinder head
l B8 l Improper valve seating 932 kPa (9.5 kg/cm*, 135 psi)300 rpm *Valve sticking in guide
9 Check if spark plugs are OK Yes Go to next step CT- page G-18
1.0-l .l mm
(0.039-0.043 in) DAMAGE AND
DETERIORATION No Clean, or replace c7 page G-18
10 Try known good ECU and check if condition
improves CT- page F-149
23UOFX-01 I
F-33