1992 MAZDA 323 Front bumper

TURBOCHARGER CONTROL SYSTEM F3
INTERCOOLER
Removal / Installation
1 I Remove the front bumper. (Refer to Section S.)
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
7-i-11 N-h l80-110 kgfem, 69-95 In-lbf 1
1.
Air hose 2. Intercooler
wrn 1 kgf-m, ft-lbf I
13EOF3-34:

S
BODY
INDEX . . . . . ..*.I........**........*.~*.~............*.......
s- 2
OUTLINE ..................................................
s- 3
UUJLINE OF CONSTRUCTION ..................
S- 3
BONNET BULGE
....................................
s- 3
RADIATOR GRILLE ................................. s- 4
FRONT BUMPER .................................... s- 4
REAR SKIRT ...........................................
s- 6
WHEEL ARCl-i MOLDING .........................
s- 5
( SERVICE j
SUPPLEMENTAL SERVICE fNFURMATION.. S- 6
BONNET BULGE
.......................................
s- 7
COMPONENTS ....................................... s- ‘7
FRONT BUMPER
.......................................
s- 8
COMPONENTS .......................................
s- 8
REAR SKIRT .............................................
S-10
COhiIPONENTS .......................................
S-10
Wt=fEEL ARCH MOLDING ............................
S-l 1
COMPONENTS .......................................
S-l 1
13EOSX301

l The exterior parts are designed to emphasize the function and appearance of the superbly proportioned
body.
: OUTtlNE OF CONSTRUCTION
1 xosx.303
.c
Bonnet bulges are provided in bonnet
. . . . . . . . . . . . ..I................~.....
s-3
A large, body-colored front bumper fascia is adopted., , ..,..,.... S-4
Wheel arch moldings are fitted to fenders . . . . . . . ,..*. l.. . . . . . . . . . . . . . . . . . S-5
- Air inlet area of radiator grille is enlarged
................................. S-4
- Bumper mesh is provided in front bumper
..............................
s-4 Rear skirt is attached under rear bumper.. ............................... S-5
13EOSX-304 BONNET BULGE
l Bonnet bulges are fittGd to the bonnet to match the dynamic appearance of the vehicle and to give it
a high-quality look.

UUTLINE
RADfATOR GRfLtE
l The air inlet area of the radiator grille is enlarged for improved cooling efficiency.
FRONT BUMPER
l The large front bu,mper includes fog lights and bumper mesh to give the vehicle a dynamic appearance.
l tight and rigid polyurethane is used for the bumper fascia.
l The air inlet area is adopted for improved cooling efficiency.
s-4
REAR SKI
l The rear 5
l Light and
WHEEL AR4
l Wheel arc

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if

S
FRONT BUMPER FRONT BUMPER
COMPONENTS
Rem’ovat ! Installation
1. Removal in the order shown
2. Install in the reverse order of
1 in the figure.
removal.
-9-9.8 Nm 170-100 kgfem,
U-87 h.lbfJ
f4-m Ikgf-m, ft-lbf J
13EOSX-312
4. Front bumper
Disassembly / Assembly
. . . . . . . . . ..m... page S-9 1. Radiator grille
2. Front conbination light
3. Headlight
5-8
Disassembh
I . Disassemi
2. Assemble
t
1. Fog lights
-
a
-I. 2. Bumper rear
3. Bumper me

FRONT BUMPER S
Disassembly / Assembly
I. Disassemble in the order shown in the figure.
2. Assemble in the reverse order of disassembly.
i
1, Fog lights
2. Bumper reinforcement
3. Bumper mesh 4. Hook cover
5. Bumper fascia

S REAR SKIRT
REAR SKIRT -
COMPONENTS
Rembal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
Note
l Remove the rear bumper to remove and install the rear skirt.
1. Rear skit-! 2. Rear bumper
S-10 WHEEL,
COMPONE
Removal I
1. Remove i
2. Install in t
I, Front why
Removi
I nstallat