1992 HONDA PRELUDE clock

Cooling System

2. Turn the radiator cap counter- clockwise, without pressing
down on it, until it stops. This
relieves any pressure remaining
in the cooling system.
3. Remove the radiator cap by pushing down and turning
counterclockwise.
4. The coolant level should be up to
the base of the filler neck. Add
coolant if it is low.
5. Put
the radiator cap back on.
Tighten it fully.
6. Pour coolant into the reserve tank. Fill it to halfway between
the MAX and MIN marks. Put
the cap back on the reserve tank.

Do no t
add any rust inhibitors or
other additives to your car's
cooling system. They may not be
compatible with the coolant or
engine components.

Replacing Coolant

The cooling system should be
completely drained and refilled
with new coolant according to the
time and mileage recommendations in the maintenance schedule. Only
use recommended antifreeze.
Draining the coolant requires
access to the underside of the car.
Unless you have the tools and
knowledge, you should have this
maintenance done by a skilled
mechanic.

Maintenance
RADIATOR CAP
RESERVE TANKProCarManuals.comMain Menu Table of Contents s t

Lights

3. Turn the lock ring counterclock-
wise (about one-quarter turn) to unlock the headlight bulb.

4. Remove
the bulb by pulling it

straight out of its recess.

5. Install

the new bulb with the
electrical connector pointing
down. Make sure all three tabs on the bulb are seated in their
slots in the headlight.
6. Turn the lock ring clockwise to

lock the bulb in place. Do not
force the ring. Check the seating

of th e
bulb's tabs if the ring will
not return to its original position.
7. Reinstall the harness connector on the bulb connector. Make sure

it locks in place.

Turn o n
the headlights to test

the new bulb.

8. (Passenger'
s
side)

Reinstall the radiator reserve
tank.

Replacing a
Parkin
g Light
Bulb

1. Use a phillips head screwdriver

to remove the screw from the top
of the fender.

2. Mov e
the parking light assembly

forward until it slides out of the
body.

3. Tur n
the socket one-quarter turn

counterclockwise to remove it
from the lens.

CONTINUED

Maintenance

SCREW
ProCarManuals.comMain Menu Table of Contents s t

Lights
4. Pull the bulb straight out of its
socket.

Push the
new bulb straight into
the socket until it bottoms
.
5. Insert
the socket back into the

lens. Turn it clockwise to lock it
in place.

6. Turn

on the parking lights to

make sure the new bulb works.

7. To

reinstall the light assembly in

the fender, line up the fingers on
the light assembly with the holes
in the fender. Push the light
assembly straight back.

8. Instal
l
the mounting screw and

tighten it securely.

Replacing a

Front Side
Marker Light Bulb

1. Use a phillips-head screwdriver to loosen the side marker assem-
bly's mounting screw.
2. Remove the side marker assem- bly from the bumper. 3. Remove the bulb holder from the
side marker assembly by turning
it one-quarter counterclockwise.
4. Pull the bulb straight out of its socket.
Push the new bulb straight into
the socket until it bottoms.

Maintenance
SCREW

BULB HOLDER
BULB

FRONT SIDE
MARKER
ASSEMBLYProCarManuals.comMain Menu Table of Contents s t

Lights
5. Push the bulb holder into the side marker assembly and turn it
clockwise until it locks.
6. Test the side marker to make sure the new bulb is working.
7. Put the side marker assembly into the bumper. Make sure the
tab on the side marker assembly
fits into the bumper slot. Tighten
the mounting screw.
Replacing a Front Turn
Signal Light Bulb

1. Use a phillips-head screwdriver to loosen the turn signal assem-
bly's mounting screw.
2. Remove the turn signal assembly from the bumper. 3. Remove the bulb holder from the
turn signal assembly by turning
it counterclockwise.
4. Remove the burned out bulb from the socket by pushing it in
and turning counterclockwise
until it unlocks.Install the new bulb.

Maintenance

SCREW
TURN SIGNAL ASSEMBLY

BULB
BULB HOLDER

CONTINUEDProCarManuals.comMain Menu Table of Contents s t

Lights
5. Push the bulb holder into the
turn signal assembly and turn it
clockwise until it locks.
6. Test the turn signals to make sure the new bulb is working.
7. Put the turn signal assembly into
the bumper. Make sure the tab
on the turn signal assembly fits
into the bumper slot. Tighten the
mounting screw.

Replacing a High-moun
t
Brake Light Bulb

1. Remove the cover by pulling it

down and sliding it forward.

2. Determin e
which bulb is burned

out.

3. Pul
l
the bulb straight out of its

socket.
Push the new bulb straight into
the socket until it bottoms.

4. Tes t
the lights to make sure the

new bulb is working.

5. Reinstal
l
the cover by sliding it

into position and pushing it up.

Maintenance
COVER
ProCarManuals.comMain Menu Table of Contents s t

Lights

Replacing Rear Bulbs

1. Open the trunk and the taillight
assembly cover.

2. Use
a phillips head screwdriver

to remove the two screws from
the bulb holder. Remove the
holder from the taillight assem-
bly.

3. Try the tail/stoplights, rear turn

signals and back-up lights to
verify which bulb needs replac- ing. Remove that bulb from the
socket by pushing it in slightly
and turning it counterclockwise.

4. Instal l
the new bulb in the socket.

Test it to make sure it works.

5. Reinstal
l
the bulb holder assem-
bly. Install the two screws and
tighten them securely.

Maintenance

COVERProCarManuals.comMain Menu Table of Contents s t

Lights

Replacing a Rear Side Marker
Light Bulb

1. Use a phillips-head screwdriver
to loosen the side marker assem-
bly mounting screw.

2. Remove
the assembly from the
fender by pulling out the back
edge and sliding the assembly

backwards.
3. Remove the socket from the

light assembly by turning it
counterclockwise.

4. Remov
e
the bulb from the socket

by pulling it straight out.
Install the new bulb. Turn on the
headlights to test the bulb.

5. Inser t
the socket in the assembly.

Turn it clockwise to lock it in
place.

6. Reinstal
l
the side marker assem-
bly in the fender. Tighten the
mounting screw securely.

Maintenance

SCREWProCarManuals.comMain Menu Table of Contents s t

Changing a Flat Tire
6. The jack is behind a cover in the right fender. Remove the cover
by turning the handle clockwise,
then pulling on the cover. 7. Turn the jack's end bracket
counterclockwise to loosen it,
then remove the jack. 8. Loosen the four wheel nuts 1/2
turn with the wheel wrench.

Taking Care of the Unexpected
HANDLE
COVER JACKProCarManuals.comMain Menu Table of Contents s t