1991 MITSUBISHI MONTERO engine

POWER BRAKE UNIT CHECK VALVE
NOTE: To test check valve before removal, stop engine, and apply
service brake to ensure air flows only toward intake
manifold.
Removal & Installation
Loosen hose clamps, and remove check valve. Before
installation, coat both ends of check valve with sealant, and install
valve with arrow (identification mark) pointing toward intake
manifold. Install check valve clamp, and secure hose clamps.
POWER BRAKE UNIT
Removal
Remove brake master cylinder. Disconnect vacuum hose from
power brake unit. Disconnect clevis pin attaching brake pedal to power
brake unit push rod. From inside vehicle, remove 4 nuts attaching
power brake unit to firewall. Remove power brake unit.
Installation
To install, reverse removal procedure. Install master
cylinder. Bleed brake system if necessary.
REAR AXLE BEARINGS & OIL SEAL
Removal (Montero)
1) With drum removed, disconnect brake line from wheel
cylinder. Disconnect bearing case from axle housing end. Remove brake
backing plate, bearing case and axle shaft as an assembly. If axle
shaft binds, use slide hammer with puller to remove.
2) Remove "O" ring and shims for preloading wheel bearing (if\
equipped). Retain shims for reassembly. To remove oil seal, use slide
hammer and hook.
3) To remove wheel bearing, straighten lock washer tabs. See
Fig. 9 . Remove lock nut using spanner wrench. Remove lock washer.
Install lock nut 3 turns on axle shaft. Install Puller (MB990787-01)
to remove axle shaft from bearing case. Rotate nuts with equal force
to remove axle shaft. Remove bearing outer race using a hammer and
drift.
Fig. 9: Removing Rear Axle Bearing (Montero)
Courtesy of Mitsubishi Motor Sales of America.
Installation
1) Apply Multipurpose Grease (SAE J310) to oil seal. Install\

CO M PU TE R R ELE A R N P R O CED URES

1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission

* Place transmission in Neutral position.
* Ensure emergency brake has been set and all accessories
are turned off.
* Start engine and bring to normal operating temperature.
* Allow vehicle to idle in Neutral for one minute.
* Initial relearn is complete: process will be completed during
normal driving.
Some manufacturers identify a specific relearn procedure
which will help establish suitable driveability during relearn stage.
These procedures are especially important if vehicle is equipped with
and electronically controlled automatic transmission or transaxle.
Always complete procedure before returning vehicle to customer.

CO OLIN G S YSTE M S PEC IF IC ATIO NS

1991 M it s u bis h i M onte ro
1991 ENGINE COOLING
Mitsubishi Cooling System Specifications
Mitsubishi: Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM SPECIFICATIONS TABLE








\









\









\









\









\









\









\







Application Specification
Coolant Replacement Interval ............. 30,000 Miles or 24 Months
Coolant Capacity
(Includes Heater & Reserve Tank)
Eclipse
1.8L .......................................... 6.6 qts. (6.2L)\
2.0L .......................................... 7.6 qts. (7.2L)\
Galant .......................................... 7.6 qts. (7.2L)\
Montero ........................................ 10.0 qts. (9.5L)\
Pickup
2WD
Automatic Transmission ....................... 6.4 qts. (6.1L)\
Manual Transmission .......................... 6.3 qts. (6.0L)\
4WD ........................................... 8.9 qts. (8.4L)\
Precis .......................................... 5.6 qts. (5.3L)\
3000GT .......................................... 8.8 qts. (8.3L)\
Pressure Cap ............................................. 11-15 psi
Thermostat Opens
Except 3000GT
Starts ............................................. 190
F (88C)
Fully Open ........................................ 212F (100C)
3000GT
Starts ............................................. 170
F (77C)
Fully Open ......................................... 190F (88C)








\









\









\









\









\









\









\

2) System input tests cycle each cruise control switch and
sensor. Use analog voltmeter or Multi-Use Tester (MB991341) for system\
input check. Use multi-use tester according to operating instructions
provided with tester. Connect leads of analog voltmeter between cruise
control terminal and ground terminal of self-diagnostic connector. See
Fig. 6.
3) Turn ignition on and check items No. 1-3 on INPUT CODE
CHART. See Fig. 9 0r 10. Start engine and check items No. 4 and 5 on
INPUT CODE CHART. To display results of each input check, press SET
switch while holding RESUME switch in ON position. Read codes. Codes
will display if circuit tested is okay.
1992
1) System input tests should be performed if no trouble codes
are stored when performing SELF-DIAGNOSTICS. System input tests cycle
each cruise control switch and sensor.
2) Use Multi-Use Tester (MB991341) for system input check.
Use multi-use tester according to operating instructions provided with
tester. Connect leads of analog voltmeter between cruise control
terminal and ground terminal of self-diagnostic connector. See Fig. 6.
Turn ignition switch to ON position. Follow INPUT CODE CHART sequence.
See Fig. 9 or 10.
3) To display results of input check, move SET switch to ON
position. Then turn MAIN switch to ON position. Within one second,
activate RESUME switch. Codes will display if circuit tested is okay.
Fig. 9: 1991 Input Code Chart
Courtesy of Mitsubishi Motor Co.

Colt, Colt 200, Mirage & Summit
Remove defogger relay located to the right of fuse block.
Ground relay terminal No. 4, and apply battery voltage to terminal No.
2. Check relay continuity using ohmmeter. Continuity should exist
between terminals No. 1 and 3. With voltage disconnected, continuity
should not be present between terminals No. 1 and 3. Ensure continuity
is present between terminals No. 2 and 4. See Fig. 2.
Colt Vista, Eclipse, Stealth & 3000GT
Remove defogger relay located on left center of firewall.
Ground relay terminal No. 4, and apply battery voltage to relay
terminal No. 3. Check relay continuity using ohmmeter. Ensure
continuity exists between terminals No. 1 and 2. With voltage
disconnected, continuity should not exist between terminals No. 1 and
2. Continuity should exist between terminals No. 3 and 4. See Fig. 2.
Galant
Remove defogger relay located in right front corner of engine
compartment. Ground relay terminal No. 1, and apply battery voltage to
terminal No. 3. Check relay continuity using ohmmeter. Continuity
should exist between terminals No. 4 and 5. See Fig. 2. With voltage
disconnected, continuity should not exist between terminals No. 4 and
5. Ensure continuity exists between terminals No. 1 and 3. See Fig. 2.
Fig. 2: Identifying Defogger Relay Terminals
Courtesy of Chrysler Motors.
DEFOGGER TIMER TEST

Colt, Colt 200, Mirage & Summit
Remove defogger timer from junction block under left side of
instrument panel. Connect a battery and test light to defogger timer
terminals. See Fig. 3. Apply battery voltage to terminal No. 7 for 5-7
seconds. Ensure test light illuminates for approximately 10 seconds.
Reapply battery voltage to terminal No. 7. Test light should go off
when voltage is applied again.
Colt Vista
With ignition switch in ON position, apply battery voltage to
terminal No. 2 of defogger timer. Timer should operate for
approximately 11 seconds then stop. See Fig. 3.
Eclipse & Galant
Remove defogger timer from interior relay block. Connect
battery voltage and test light to timer. See Fig. 3. Ensure test light
illuminates for approximately 11 seconds when battery voltage is
applied to terminal No. 4. Reapply battery voltage to terminal No. 4
and observe test light. Test light should go off.
Fig. 3: Identifying Defogger Timer Terminals
Courtesy of Chrysler Motors.
GRID TEST
1) Start engine and operate at 2000 RPM. Ensure battery is
fully charged. Turn defogger switch to ON position. Using a voltmeter,
check voltage at center section of each grid wire. If voltage is
approximately 6 volts, grid wire is okay. If voltage is approximately
12 volts, an open is present in the negative circuit. Move probe
slowly toward the negative terminal to determine location of open
circuit.
2) If voltage is zero volt, an open is present in the
positive circuit. Move probe slowly toward the positive terminal to

of shaft to prevent boot damage during removal.
3) Remove DOJ boot. Note size of boot. Remove dust cover from
shaft. Straighten BJ boot protector and remove protector band. Move
boot protector toward BJ side of shaft and remove. Remove BJ boot.
CAUTION: Drive axle and BJ are serviced as a unit. DO NOT
disassemble BJ and drive axle.
REASSEMBLY
1) Coat shaft with light coat of grease. Wrap splines with
tape. Install BJ boot, bands and DOJ boot on shaft. Ensure correct
size boot is installed in proper location.
2) Boot bands must be installed so lever is pulled toward
rear of vehicle when band is tightened. Pack proper amount of grease
in BJ and BJ boot. See GREASE APPLICATION table.
3) Place DOJ cage on shaft with smaller diameter installed
first. Install circlip, DOJ inner race, and snap ring on shaft. Apply
grease to DOJ inner race and cage. Install balls into cage.
4) Apply proper amount of grease to outer DOJ race. Install
shaft into DOJ outer race. Apply proper amount of grease to DOJ outer
race and install circlip. See GREASE APPLICATION table.
5) Place DOJ boot over DOJ outer race. Install boot bands so
lever is pulled toward rear of vehicle when band is tightened. Adjust
DOJ boot bands to have proper distance between centerline of boot
bands. See BOOT BAND SPECIFICATIONS table. This distance is necessary
to control air in DOJ boot. Tighten boot bands.
6) Install boot protector and band. Install dust cover on
shaft. Use a pipe with O.D. of 2.68" (68.0 mm), wall thickness of .09"\
(2.3 mm) and with overall length of 6.70" (170.1 mm) to install dust\
cover.
GREASE APPLICATION









\









\









\









\









Application Ozs. (g)
BJ Boot
Montero
3.0L Engine .................. 4.6 (130)
All Others .................... 3.9 (110)
DOJ Outer Race
Montero
3.0L Engine ................... 2.3 (60)
All Others ..................... 1.9 (55)









\









\









\









\









BOOT BAND SPECIFICATIONS








\









\









\









\









Application In. (mm)
All Models .......... 3.03-3.27 (76.9-83.0)









\









\









\









\









DIFFERENTIAL DISASSEMBLY
1) Remove differential carrier from vehicle. See DIFFERENTIAL
CARRIER R & I in this article. Remove cover. Mark bearing caps for
reassembly reference. Remove bearing caps. Remove differential case
assembly from carrier.
CAUTION: Ensure adjusting spacers, bearing caps, gears and side
bearings are marked for reassembly reference. Components