1991 MITSUBISHI MONTERO brake light

air filter adblue fuel pressure radio window checking oil

Page 174 of 1333

$MITSUBISHI MONTERO 1991 Service Manual \003* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES * 1 991 M it s u bis h i M onte ro GENERAL INFORMATION Brake Systems - Motorist Assurance Program Stan$

Page 175 of 1333

MITSUBISHI MONTERO 1991 Service Manual SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACH

SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not

Page 179 of 1333

MITSUBISHI MONTERO 1991 Service Manual NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATE

NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATES
BACKING PLATE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Anchor pin bent ......... B .. Require repair or replacement.
Anchor pin broken ....... A ............ Require replacement.
Anchor pin worn, affecting
structural integrity ... B ............ Require replacement.
Backing plate bent ...... B .. Require repair or replacement.
Backing plate broken .... A ............ Require replacement.
Backing plate cracked ... B .. Require repair or replacement.
Corroded, affecting
structural integrity .... A ............ Require replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Shoe lands worn ......... A .. Require repair or replacement.
\
\
\
\
\
\
\

BRAKE FLUID
CAUTION: Most manufacturers prohibit the use of DOT 5 brake fluid
in a system equipped with ABS.
DOT 3, DOT 4, and DOT 5.1 brake fluids are clear or light
amber in color. DOT 5 brake fluid is violet in color. Correct fluid
required for the brake system is stamped on the master cylinder cover.
BRAKE FLUID INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Beyond service interval . 3 .. Suggest flushing and refilling
with correct fluid.
Brake fluid type
incorrect .............. B .. Require flushing and refilling
with correct fluid.
Contaminated, for example,
fluid other than brake
fluid present .......... A or B ....... ( 1) Require service.
Hydraulic component ..... 3 .. Suggest flushing and refilling
overhaul or replacement with correct fluid.
Rubber master cylinder
cover gasket distorted
and gummy .............. A .......... ( 2) Require replacement
of gasket.
( 1) - If a fluid other than brake fluid is present in the brake
system which DOES affect the rubber parts, the required
service is to:
* Remove all components having rubber parts from the
system.
* Flush lines with denatured alcohol or brake cleaner
* Repair or replace all components having rubber parts
* Flush and fill with correct brake fluid. (Code A)
If a fluid other than brake fluid is present in the brake

Page 180 of 1333

MITSUBISHI MONTERO 1991 Service Manual system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake

system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.
\
\
\
\
\
\
\

BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.
\
\
\
\
\
\
\

BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\

BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.

Page 199 of 1333

MITSUBISHI MONTERO 1991 Service Manual specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1

specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal
particles or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable; check
for accepted cleaning procedure.
\
\
\
\
\
\
\

STEEL BRAKE LINES
STEEL BRAKE LINE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Fitting incorrect (for
example, compression
fitting) ............... B ............ Require replacement.
Flare type incorrect .... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Line material incorrect
(copper, etc.) ......... B ............ Require replacement.
Restricted .............. A ............ Require replacement.
Routed incorrectly ...... B ..... Require routing correction.
Rust-pitted ............. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\

STOPLIGHT SWITCHES
See BRAKE STOPLIGHT SWITCHES .
SWITCHES
NOTE: Copied from Electrical UIGs & added "float saturated" from
old fluid level sensor switches.
STEEL BRAKE LINE INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.

Page 208 of 1333

MITSUBISHI MONTERO 1991 Service Manual BRAK E S YSTE M

1991 M it s u bis h i M onte ro
1991 BRAKES
Disc & Drum
Chrysler Motors: Ram-50;
Mitsubishi: Montero, Pickup
DESCRIPTION

BRAK E S YSTE M

1991 M it s u bis h i M onte ro
1991 BRAKES
Disc & Drum
Chrysler Motors: Ram-50;
Mitsubishi: Montero, Pickup
DESCRIPTION
Brake system consists of a master cylinder, vacuum power
brake unit, proportioning valve and self-adjusting assembly. Pickup
and Ram-50 models have a Load-Sensing Proportioning Valve (LSPV). All
models are equipped with front disc brakes and rear drum brakes.
Parking brake assembly activates rear brakes.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
Montero
Bleed brake system in following order: right rear, right
front and left front (one circuit handles both rear brakes).
Pickup & Ram-50
Bleed brake system in following order: right rear, left rear,
LSPV, right front and left front.
ADJUSTMENTS
BRAKE PEDAL HEIGHT & FREE PLAY
1) Separate connector from stoplight switch, and loosen lock
nut. Position switch so it does not contact brake pedal arm. Adjust
brake pedal height by rotating master cylinder push rod (yoke, if
equipped) until distance from top of brake pedal to floor board is
correct. See BRAKE PEDAL SPECIFICATIONS table.
2) DO NOT depress push rod. Tighten lock nut, and ensure
brake pedal height is within specification. Start engine to evacuate
brake booster chamber. Stop engine, and apply brake several times to
remove vacuum from brake booster.
3) Using hand pressure, depress brake pedal to measure free
play before resistance is felt. If distance is incorrect, bleed the
brake hydraulic system, and check for misadjusted brakes. Refer to the
BRAKE PEDAL SPECIFICATIONS table.
BRAKE PEDAL SPECIFICATIONS TABLE
\
\
\
\
\
\

Free Play Pedal Height
Application In. (mm) In. (mm)
Montero ............ .12-.31 (3-8) ... 7.5-7.7 (191-196)
Pickup & Ram-50 .... .12-.31 (3-8) ........... 6.5 (166)
\
\
\
\
\
\

LOAD-SENSING PROPORTIONING VALVE (LSPV) (Pickup & Ram-50)
Park vehicle on level surface. Remove all luggage and
passengers. Ensure lever is not against stopper bolt. Check spring

Page 211 of 1333

MITSUBISHI MONTERO 1991 Service Manual brake pedal to center shoes, and check pedal travel. Rotate brake drum
to verify free movement.
STOPLIGHT SWITCH
Loosen lock nut, and adjust switch-to-pedal arm clearance to
.02-.04"

brake pedal to center shoes, and check pedal travel. Rotate brake drum
to verify free movement.
STOPLIGHT SWITCH
Loosen lock nut, and adjust switch-to-pedal arm clearance to
.02-.04" (.5-1.0 mm). Tighten lock nut. DO NOT depress master cylinder
push rod during stoplight switch adjustment.
TESTING
POWER BRAKE UNIT
Check Valve Inspection
Remove vacuum hose from power brake unit. Remove check valve
from hose (if possible). Using a vacuum pump, ensure airflow is in
direction of intake manifold only.
System Check
1) Run engine for 2 minutes, and shut it off. Depress brake
pedal several times with normal pressure. If pedal height gradually
becomes higher with successive applications, power brake unit is okay.
If pedal height remains steady, power brake unit is faulty.
2) With engine stopped, depress brake pedal repeatedly until
it's height no longer falls. Hold brake pedal down, and start engine.
If pedal moves downward slightly, power brake unit is okay. If pedal
height does not change, power brake unit is faulty.
3) With engine running, press and hold brake pedal and shut
off engine. Hold brake pedal for 30 seconds. Brake pedal height should
not change. If pedal height falls, power brake unit is faulty.
LOAD-SENSING PROPORTIONING VALVE (LSPV) (PICKUP & RAM-50)
1) Before diagnosing Load-Sensing Proportioning Valve (LSPV)\
,
ensure all other brake components are operating properly. When all
other brake system components are determined to be okay, perform LSPV
test beginning with next step.
2) Ensure unladen vehicle is on level ground. Ensure lever is
not contacting stopper bolt. See Fig. 1.
3) When lever is pushed toward valve, distance from LSPV
lever hole and support hole must be 6.97-7.09 in. (177-180 mm). If
measured distance is not within specification, loosen support bolt.
Adjust support until measured distance is within specification.
4) After measured distance is within specification, connect
pressure gauges to input and output ports of LSPV. See Fig. 4. Bleed
brake system. See BLEEDING BRAKE SYSTEM .
Fig. 4: Connecting Pressure Gauges to LSPV (Pickup & Ram-50)
Courtesy of Mitsubishi Motor Sales of America.

Page 212 of 1333

MITSUBISHI MONTERO 1991 Service Manual 5) Remove the LSPV load-sensing spring. Slowly depress the
brake pedal. Check the readings on the pressure gauges. Refer to the
LSPV PRESSURE SPECIFICATIONS table.
6) Install LSPV lo

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 32 next >

wheel torque 4WD fuel automatic transmission mirror check transmission fluid