1991 MITSUBISHI MONTERO ECU

WIRING HARNESSES AND CONNECTORS
WIRING HARNESS AND CONNECTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Insulation damaged,
conductors exposed ..... A .. Require repair or replacement.
Insulation damaged,
conductors not exposed . 1 ............ Suggest replacement.
Open .................... A .. Require repair or replacement.
Protective shield
(conduit) melted ....... 2 ........... ( 1) Suggest repair or
replacement.
Protective shield
(conduit) missing ...... 2 .. Suggest repair or replacement.
Resistance (voltage drop)
out of specification ... A .. Require repair or replacement.
Routed incorrectly ...... B ................. Require repair.
Secured incorrectly ..... B ................. Require repair.
Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Voltage drop out of
specification .......... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.









\









\









\









\









\









\









\

BATTERY CABLE, WIRE AND CONNECTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Insulation damaged,
conductors exposed ..... A ........... ( 2) Require repair or
replacement.
Insulation damaged,
conductors not exposed . 1 ............ Suggest replacement.
Open .................... A .. Require repair or replacement.
Protective shield
(conduit) melted ....... 2 ........... ( 1) Suggest repair or
replacement.
Protective shield
(conduit) missing ...... 2 .. Suggest repair or replacement.
Resistance (voltage drop)
out of specification ... A .. Require repair or replacement.
Routed incorrectly ...... B ................. Require repair.
Secured incorrectly ..... B ................. Require repair.
Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Voltage drop out of
specification .......... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Exposed conductor at replacement (aftermarket) terminal
end does not require repair or replacement.









\









\









\









\









\









\









\


BATTERY CONNECTORS
See BATTERY CABLES, WIRES AND CONNECTORS .
BATTERY TRAYS AND HOLD DOWN HARDWARE

BATTERY TRAY AND HOLD DOWN HARDWARE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Battery improperly
secured ................ 2 ................. Suggest repair.
Bent, affecting
performance ............ A .. Require repair or replacement.
Bent, not affecting
performance ............ .. ....... No service suggested or
required.
Broken, affecting
performance ............ A .. Require repair or replacement.
Broken, not affecting
performance ............ .. ....... No service suggested or
required.
Corroded, affecting
performance ............ A .. Require repair or replacement.
Corroded, not affecting
performance ............ 2 .. Suggest repair or replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Missing ................. C ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Water drain clogged ..... A ................. Require repair.









\









\









\









\









\









\









\


BATTERY WIRES
See BATTERY CABLES, WIRES AND CONNECTORS .
BELT-DRIVEN AIR PUMPS
BELT-DRIVEN AIR PUMP INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 ............ Suggest replacement.
Pulley alignment
incorrect .............. B .. Require repair or replacement.
Pulley bent ............. A ............ Require replacement.
Pulley cracked .......... A ............ Require replacement.
Pulley loose ............ A .. Require repair or replacement.
Pulley missing .......... C ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads

WIRING HARNESS AND CONNECTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Insulation damaged,
conductors exposed ..... A .. Require repair or replacement.
Insulation damaged,
conductors not exposed . 1 ............ Suggest replacement.
Open .................... A .. Require repair or replacement.
Protective shield
(conduit) melted ....... 2 ........... ( 1) Suggest repair or
replacement.
Protective shield
(conduit) missing ...... 2 .. Suggest repair or replacement.
Resistance (voltage drop)
out of specification ... A .. Require repair or replacement.
Routed incorrectly ...... B ................. Require repair.
Secured incorrectly ..... B ................. Require repair.
Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Voltage drop out of
specification .......... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.









\









\









\









\









\









\









\

improperly.
CONSEQUENCE OF DEFECT:
The safety belts would not provide adequate protection to an occupant
in a vehicle crash.
CORRECTIVE ACTION:
Owners should promptly check the condition and operation of both front
safety belt buckles and carefully inspect the red release button for
any breaks or cracks. They should ensure that both buckles are
operating properly by inserting each latch plate into its buckle,
tugging on the belt to make sure the latch is securely locked, and
then pressing the release button. The latch plate should pop out of
the buckle when the button is pressed. If either release button shows
a sign of breaking or cracking or if either buckle fails to operate
properly, owners should promptly contact their authorized dealer to
schedule an appointment to have the buckle replaced or repaired, free
of charge. The manufacturer is developing a remedy designed to prevent
failure of the buttons that are not currently broken.
NOTE:
If your vehicle is presented to an authorized dealer on an agreed upon
service date and the remedy is not provided free of charge within a
reasonable time, please contact Mitsubishi at 1-800-222-0037. Also
contact the National Highway Traffic Safety Administration's Auto
Safety Hotline at 1-800-424-9393.
ADDITIONAL INFORMATION:
The National Highway Traffic Safety Administration operates Monday
through Friday from 8:00 AM to 4:00 PM, Eastern Time. For more
information call (800) 424-9393 or (202) 366-0123. For the hearing
impaired, call (800) 424-9153.

With lever set at OUTSIDE position, outside air is allowed to enter
and/or pass through heater. With lever set at INSIDE position, air is
recirculated inside passenger compartment.
BLOWER SWITCH
The blower can be operated at different fan speeds to
regulate amount of air forced through vehicle. Fan speed will increase
as switch is turned or moved right.
AIR CONTROL INDICATION SYSTEM
This system consists of indication lights built into
instrument cluster and 4 switches connected to various control levers.
An indication light glows when heater blower is on. Lights also
indicate choice of outlets and whether air source is inside or outside
vehicle. In addition, temperature of air directed from outlets is
indicated for each air outlet by light colors of green (cool air) and
orange (warm air).
ADJUSTMENTS
HEATER (TEMPERATURE) CONTROL VALVE
Place control lever to indicated position. See TEMPERATURE
CONTROL CABLE ADJUSTMENT table. See Fig. 3. Connect cable to heater
control valve and/or air damper lever according to table. Secure cable
sleeve using clips. With engine running, check for coolant leaks and
check operation of heater control valve. If heater control valve does
not operate properly, adjust by moving cable sleeve forward or
backward at retaining clip.
TEMPERATURE CONTROL CABLE ADJUSTMENT TABLE









\









\









\









\









\









\









\







Application Control Lever Water Valve
Position Lever Position
Montero .................... Far Left ............... Toward cable
Pickup & Ram-50 ............ Far Left ........ (2) Away from cable
(2) - Disconnect link between air damper lever and water valve
lever. Close water valve. Close air damper. Reconnect link.
Attach cable to clip.









\









\









\









\









\









\









\







Fig. 3: Adjusting Temperature Control Cable (Typical)
Courtesy of Mitsubishi Motor Sales of America.
INSIDE/OUTSIDE AIR SELECTION CABLE

Move control lever to INSIDE position. Connect cable to
damper lever with outside air intake to heater closed. Apply
multipurpose grease to rotating portions of sliding lever. Check for
proper damper operation by moving control lever. To adjust, press air
control lever toward cable and move outer wire at retaining clip. See
Fig. 4.
Fig. 4: Adjusting Air Selection Cable (Typical)
Courtesy of Mitsubishi Motor Sales of America.
MODE SELECTOR LEVER
Place selection lever in DEF position, and remove cable clip.
Ensure defroster door is fully open. Secure cable sleeve using clips.
Move lever to other positions to check for correct operation. Adjust
cable, if necessary, by moving sleeve forward or backward at retaining
clip.
TROUBLE SHOOTING
BLOWER MOTOR INOPERATIVE
Blown blower fuse. Blower motor improperly grounded.
Defective switch or faulty blower motor wiring connections. Foreign
object in fan.
INSUFFICIENT HEAT

Removal (Montero)
1) Move temperature control lever to WARM position. Drain
coolant from vehicle. Disconnect heater hoses from heater unit. See
Fig. 1.
2) Remove lap heater ducts. Remove hood release bracket.
Using screwdriver, release tabs and remove left and right demister
grilles. Remove glove box frame attaching screws, and remove glove
box. Remove passenger lap heater duct.
3) Using screwdriver and shop towel, carefully pry at top
center of instrument cluster cover, and remove cover. Remove 2 screws
at bottom of instrument panel and one bolt at top of instrument panel.
Gently pull instrument cluster out, and disconnect speedometer cable
and electrical connections. Remove instrument cluster.
4) Remove 4 screws, and disconnect electrical connections on
back of instrument cluster. Remove instrument cluster. Handle
instrument cluster carefully. Instrument cluster can be damaged if
dropped.
5) Remove center console knobs and side screw plugs. Remove
screws, disconnect electrical connections and remove console. Remove 6
bolts and console bracket (center dash reinforcement). Disconnect
radio connections while removing console bracket.
6) Remove horn pad and steering wheel retaining nut. Mark
steering wheel and steering shaft for reassembly reference. Using
steering wheel puller, remove steering wheel.
7) Using screwdriver, carefully pry out dash plug at upper
center of dash panel. Remove 3 upper dash mounting nuts, one upper
screw above steering column, and 2 lower mounting screws. Remove dash
panel.
8) Remove control cables at heater unit. Remove heater unit
attaching screws. Remove heater ducts. Remove heater unit. Remove
heater control lever arm.
9) Remove heater control valve cover. Remove heater pipe and
heater control valve. Disconnect control arm linkage. Remove control
arm. Remove heater core by moving it sideways.
Installation
1) To install, reverse removal procedure. Insert heater hoses
fully into pipes, and clamp securely to prevent leaks. Connect heater
hoses with 1-1.2" (25-30 mm) overlap on outlet.
2) When filling radiator with coolant, first open heater
control valve fully and run engine to circulate coolant and discharge
air from inside heater and engine cooling system. Stop engine, and add
coolant.
3) Adjust all control cables. When installing heater hose
grommets, apply sealer. After installing heater control assembly,
ensure each lever operates smoothly.
Removal (Pickup & Ram-50)
1) Disconnect battery ground cable. Place heater control
lever to far right. Drain coolant. Using trim stick, pry out hazard
switch and remove electrical connection. Remove 4 instrument cluster
cover screws, and remove cover. Remove 4 instrument cluster screws.
Tilt instrument cluster out, and disconnect speedometer cable and
electrical connections. Remove cluster.
2) Remove fuse box cover and fuse box assembly. Remove glove
box. Remove defroster air ducts. Disconnect heater control cables.
Using trim stick, pry under and remove speaker grilles. Remove clock
or coin box in center of dash. Remove center dash hole cover (located
above clock).
3) Remove 2 center support cover screws, and remove cover.
Remove shift knob and 6 console attaching screws. Remove console.
Ensure all electrical connections are free of dash panel. Remove 3 top
nuts, one bolt above steering column, and side and lower attaching