1991 MITSUBISHI MONTERO timing belt
[x] Cancel search: timing beltPage 567 of 1333
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
TIMING BELT SPROCKETS
TIMING BELT SPROCKET INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Alignment incorrect ..... B ................. Require repair.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bent .................... A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Key damaged ............. A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Pulley damaged, affecting
belt life .............. A ............ Require replacement.
Sprocket damaged,
affecting belt life .... A .. Require repair or replacement.
Sprocket loose .......... B .. Require repair or replacement.
Sprocket-to-shaft
alignment incorrect ..... B .. Require repair or replacement.
\
\
\
\
\
\
\
TIMING BELTS
TIMING BELT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Adjustment incorrect .... 2 ......... ( 1) Suggest adjustment.
Alignment incorrect ..... B ........... ( 2) Further inspection
required.
Broken .................. A ............ Require replacement.
Cam timing out of
specification .......... B ................. Require repair.
Cracked ................. 1 ............ Suggest replacement.
Fluid-soaked ............ 1 ... Suggest replacement. Further
inspection required.
Frayed .................. 1 ............ Suggest replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle OEM recommended
Page 568 of 1333
service intervals.
Missing ................. C ........ (3) Require replacement.
Noisy ................... 2 .......... ( 4) Further inspection
required.
See note below.
Plies separated ......... A ............ Require replacement.
Tension out of
specification .......... B ........... Require adjustment or
replacement.
Teeth missing ........... A ............ Require replacement.
( 1) - Inspect belt tensioners, pulleys, and cover.
( 2) - Determine cause of incorrect alignment and require repair.
( 3) - CAUTION: Internal engine damage may result from timing
belt damage/failure.
( 4) - Determine cause of noise and suggest repair.
\
\
\
\
\
\
\
TORQUE STRUTS
TORQUE STRUT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A ............ Require replacement.
Body dented ............. A .......... ( 1) Further inspection
required.
Body punctured .......... A ............ Require replacement.
Bushing deteriorated,
affecting performance .. A ............ Require replacement.
Bushing deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Bushings missing ........ C ............ Require replacement.
Bushings separated from
mounting eye ........... 1 ............ Suggest replacement.
Damping (none) .......... A ............ Require replacement.
Leaking oil, enough for
fluid to be running down
the body ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 .......... ( 2) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Seized .................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Require replacement of units where dents restrict strut
piston rod movement. If dents don't restrict movement, no
service is suggested or required.
( 2) - If noise is isolated to shock or strut, suggest replacement.
Page 635 of 1333
IN TE R FE R EN CE V ER IF IC ATIO N C HEC K F O R O HC E N G IN E
1991 Mitsubishi Montero
Maintenance & Service Information
1983-96 Mitsubishi - Timing Belt Information
Cordia, Diamante, Eclipse, Expo, Expo LRV, Galant, Mirage,
Montero, Pickup, Precis, Sigma, Tredia, Van, 3000GT
TIMING BELT INTERFERENCE VERIFICATION INFORMATION
TIMING BELT INTERFERENCE CAUTION
NOTE: CAMSHAFT DRIVE BELTS OR TIMING BELTS - The condition of
camshaft drive belts should always be checked on vehicles
which have more than 50,000 miles. Although some
manufacturers do not recommend replacement at a specified
mileage, others require it at 60,000-100,000 miles. A
camshaft drive belt failure may cause extensive damage to
internal engine components on most engines, although some
designs do not allow piston-to-valve contact. These designs
are often called "Free Wheeling". Many manufacturers changed
their maintenance and warranty schedules in the mid-1980's to
reflect timing belt inspection and/or replacement at
50,000-60,000 miles. Most service interval schedules shown in
this section reflect these changes. Belts or components
should be inspected and replaced if any of the following
conditions exist:
* Crack Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
TIMING BELT INTERFERENCE CHECK MENU
TIMING BELT INTERFERENCE VERIFICATION TABLE ( 1) \
\
\
\
\
\
Replacement Interval
Application Engine (Miles)
Passenger Cars
Cordia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
Diamante
1992-96 ...... ( 2) 3.0L V6 (DOHC) ............. 60,000
3.0L V6 (SOHC) ........... ( 4) 60,000
Eclipse
1990-94 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
1990-95 ....... ( 2) 2.0L 4-Cyl. ........... ( 4) 60,000
1990-94 ... ( 2) 2.0L 4-Cyl. Non-Turbo ..... ( 4) 60,000
1990-96 ..... ( 2) 2.0L 4-Cyl. Turbo ....... ( 4) 60,000
1996 ........... ( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo
1992-95 .......... 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo LRV
1995 ............. 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Galant
Page 636 of 1333
1985-87 ........ (2) 2.4L 4-Cyl. .......... ( 4) 60,000
1988 ............... 3.0L V6 .............. ( 3) 60,000
1989-93 .... ( 2) 2.0L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.0L 4-Cyl. (SOHC) ........ ( 4) 60,000
1994-96 .... ( 2) 2.4L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.4L 4-Cyl. (SOHC) ........ ( 4) 60,000
Mirage
1985-96 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
1985-88 ..... ( 2) 1.6L 4-Cyl. Turbo ........... 60,000
1989, 1991 ..... ( 2) 1.6L 4-Cyl. .............. 60,000
1993-96 ........... 1.8L 4-Cyl ................ 60,000
Precis
1987-93 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
Sigma
1989-90 ............ 3.0L V6 .............. ( 3) 60,000
Tredia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
3000GT
1991-96 .......... ( 2) 3.0L V6 ................ 60,000
Light Trucks
Montero
1985-96 ............ 3.0L V6 .............. ( 3) 60,000
1994-96 ............ 3.5L V6 .............. ( 3) 60,000
Pickup
1983-89 ........... 2.0L 4-Cyl. ........... ( 3) 60,000
1983-86 ... ( 2) 2.3L 4-Cyl. Turbo Diesel .. ( 4) 60,000
1990-96 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
3.0L V6 .............. ( 3) 60,000
Van
1987-90 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
( 1) - Other interference engine applications may exist which
are not indicated here.
( 2) - Interference engine. Check for possible damage to
piston(s) or valve(s) if there has been a timing belt
failure.
( 3) - Although the vehicle manufacturer does not recommend a
specific scheduled maintenance interval, aftermarket
belt manufacturers suggest the belt be replaced at
60,000 mile intervals.
( 4) - Vehicle manufacturer recommends replacing all belts at
the same time.
\
\
\
\
\
\
Page 662 of 1333
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
CAMSHAFT TIMING BELT
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1983-86 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 701 of 1333
CAMSHAFT TIMING BELT REPLACEMENT INFORMATION
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SEVERE & NORMAL SERVICE DEFINITIONS
NOTE: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at mileage intervals based on vehicle
operation. Service schedules are based on the following primary
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
NOTE: The following services are to be performed on vehicles
subjected to severe service. See SEVERE & NORMAL SERVICE
DEFINITIONS. This service is to be performed in addition
to the normal services listed in the NORMAL MAINTENANCE
SERVICE SCHEDULES.
SEVERE SERVICE CONDITIONS/ACTIONS TABLE
\
\
\
\
\
\
\
Condition Action Item Perform Every (1)
Page 713 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fuel Filter](/manual-img/19/57332/w960_57332-712.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fuel Filter")
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
Page 723 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\](/manual-img/19/57332/w960_57332-722.png "MITSUBISHI MONTERO 1991 Service Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\")
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4