1991 MITSUBISHI MONTERO oil temperature
[x] Cancel search: oil temperaturePage 690 of 1333
Installation
1) To install, reverse removal procedure. Injectors may be
removed after fuel rail is removed from intake manifold. Use new
insulators and "O" rings when installing injectors.
2) Use spindle oil or gasoline on "O" ring. Install injectors
into fuel rail with a twisting motion. Adjust throttle and kickdown
cable (if applicable). Do not drop injectors while removing or
installing fuel rail.
OXYGEN (O2) SENSOR
Removal & Installation
1) O2 Sensor is mounted in exhaust pipe below exhaust header.
It is equipped with a permanent pigtail which must be protected from
damage when sensor is removed. Ensure sensor is free of contaminants,
avoid using cleaning solvents of any type. Sensor may be difficult to
remove when engine temperature is less than 120
F (48 C).
2) Always use anti-seize compound on threads before
installation. On non-turbo models, remove sensor using Remover
(MD998703). On turbo models, use Remover (MD998748) on Eclipse and
Galant, or Remover (MD998770) on Stealth and 3000GT. Tighten oxygen
sensor to specification. See TORQUE SPECIFICATIONS table.
THROTTLE BODY
Removal
Disconnect air intake hose. Remove accelerator and automatic
speed control cables (if equipped). Disconnect fuel vapor hose,
electrical harness connector, vacuum hose and coolant hoses. Remove
throttle body retaining bolts.
Disassembly
Remove throttle position sensor. Remove idle speed control
motor. Remove throttle bracket and connector bracket (if equipped).
Remove idle position switch and adjusting nut.
NOTE: DO NOT remove throttle valve. DO NOT use cleaning solvents
on throttle position sensor, idle speed control motor or
idle position switch.
Cleaning
Clean all parts except those noted in solvent. Check vacuum
port and passage for clogging. Clean vacuum, vapor and fuel passages
with compressed air.
Reassembly
To reassemble, reverse disassembly procedure.
Installation
To install, reverse removal procedure.
THROTTLE POSITION SENSOR/SWITCH
Removal & Installation
Throttle position sensor/switch is located on throttle body.
Disconnect TPS electrical connector. Remove bolts holding TPS and
remove TPS. To install, reverse removal procedure. Tighten throttle
position sensor/switch to specification. See TORQUE SPECIFICATIONS
table. For adjustment procedure, see ON-VEHICLE ADJUSTMENTS article.
TURBOCHARGERS
Page 698 of 1333
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare hands. Eye
protection should be worn when handling or working around halogen
bulbs.
POWER STEERING FLUID
When adding power steering fluid, avoid spilling. Damage to
alternator, located beneath power steering reservoir, could result.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to 15
minutes even after engine is turned off.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1987-91 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 701 of 1333
CAMSHAFT TIMING BELT REPLACEMENT INFORMATION
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SEVERE & NORMAL SERVICE DEFINITIONS
NOTE: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at mileage intervals based on vehicle
operation. Service schedules are based on the following primary
operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
NOTE: The following services are to be performed on vehicles
subjected to severe service. See SEVERE & NORMAL SERVICE
DEFINITIONS. This service is to be performed in addition
to the normal services listed in the NORMAL MAINTENANCE
SERVICE SCHEDULES.
SEVERE SERVICE CONDITIONS/ACTIONS TABLE
\
\
\
\
\
\
\
Condition Action Item Perform Every (1)
Page 702 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \
\
\b\
\b\
\b\
\
\
Short Trips In Replace Engine Oil](/manual-img/19/57332/w960_57332-701.png "MITSUBISHI MONTERO 1991 Service Manual \
\
\b\
\b\
\b\
\
\
Short Trips In Replace Engine Oil")
\
\
\b\
\b\
\b\
\
\
Short Trips In Replace Engine Oil 3,000 Miles or 3 Months
Freezing
\
\b\
\b\
\
\
Temperatures Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Towing Or Replace Engine Oil 3,000 Miles or 3 Months
Commercial Use
\
\b\
\b\
\
\
Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\b\
\b\
\b\
\
\
Driving Off-Road Replace Engine Oil 3,000 Miles or 3 Months
Or In Salty Or
\
\b\
\b\
\
\
Sandy Areas Inspect Cooling 6,000 Miles or 6 Months
System
\
\b\
\b\
\
\
Replace Engine Oil 6,000 Miles or 6 Months
Filter
\
\b\
\b\
\
\
Inspect Throttle ONLY ONCE AT FIRST:
Position 15,000 Miles
\
\b\
\b\
\
\
Inspect Drive Belt START AT: 15,000 Miles;
Tension REPEAT EVERY SUBSEQUENT:
30,000 Miles
\
\b\
\b\
\
\
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
Page 704 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\](/manual-img/19/57332/w960_57332-703.png "MITSUBISHI MONTERO 1991 Service Manual Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\")
Replace A/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace M/T Fluid 30,000 Miles
\
\b\
\b\
\
\
Replace Transfer 30,000 Miles
Case Fluid
\
\
\
\
\
\
\
(
1) - Perform these services at the mileage or number of months
(since the last time), whichever comes first.
\
\
\
\
\
\
\
\f
NORMAL MAINTENANCE SERVICE SCHEDULES
The following service schedules refer to vehicles driven
under normal operating conditions. For vehicles driven under severe
conditions, additional services may be necessary. See
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES) above in
this article for additional service requirements.
7500 MILE (12,000 KM) SERVICE
7500 MILE (12,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Change Engine Oil
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
15,000 MILE (24,000 KM) SERVICE
15,000 MILE (24,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
Page 705 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels](/manual-img/19/57332/w960_57332-704.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels")
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)
Page 706 of 1333
1989-94
2.6L ........................................ 1.9 Qts. (1.8L)
3.0L ........................................ 2.7 Qts. (2.6L)
1994
3.5L ........................................ 2.7 Qts. (2.6L)
1995
3.0L ........................................ 2.7 Qts. (2.6L)
3.5L ........................................ 3.3 Qts. (3.2L)
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
Manual Transmission
1987-91 ...................................... 2.3 Qts. (2.2L)
1992 ......................................... 2.4 Qts. (2.3L)
1993-94 ...................................... 2.6 Qts. (2.5L)
Transfer Case
1987-91 ...................................... 2.3 Qts. (2.2L)
1992-94 ...................................... 2.4 Qts. (2.3L)
\
\
\
\
\
\
\
\f
22,500 MILE (36,000 KM) SERVICE
22,500 MILE (36,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Change Engine Oil
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
30,000 MILE (48,000 KM) SERVICE
30,000 MILE (48,000 KM) SERVICE \
\
\
\
\
\
\
Page 707 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\](/manual-img/19/57332/w960_57332-706.png "MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\")
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature