1991 MITSUBISHI MONTERO fuel

\003
E - T H EO RY/O PER ATIO N - E FI

1 991 M it s u bis h i M onte ro
1990-91 ENGINE PERFORMANCE
Chrysler/Mitsubishi Theory & Operation - Fuel Injection
All Models
INTRODUCTION
This article covers basic description and operation of engine
performance-related systems and components. Read this article before
diagnosing vehicles or systems with which you are not completely
familiar.
AIR INDUCTION SYSTEM
NON-TURBOCHARGED ENGINES
All Chrysler/Mitsubishi engines with Port Fuel Injection
(PFI), called Multi-Point Injection (MPI) by the manufacturer, use t\
he
same basic air induction system. Remote air filter (with airflow
sensor) is ducted to a plenum-mounted throttle body.
TURBOCHARGED ENGINES
In addition to basic air induction system used on all other
models, turbocharging system components include turbocharger, air-to-
air intercooler, air by-pass valve, wastegate actuator, wastegate
control solenoid valve and intake ducting.
Wastegate Control Solenoid Valve
Engine Control Unit (ECU) energizes solenoid valve,
controlling leakage rate of turbocharger pressure to wastegate
actuator.
COMPUTERIZED ENGINE CONTROLS
Multi-Point Injection (MPI) is a computerized engine control
system which controls fuel injection, ignition timing, idle speed and
emission control systems.
ELECTRONIC CONTROL UNIT (ECU)
NOTE: Components are grouped into 2 categories. The first category
covers INPUT DEVICES, which control or produce voltage
signals monitored by the Engine Control Unit (ECU). The
second category covers OUTPUT SIGNALS, which are components
controlled by the ECU.
ECU receives and processes signals from input devices. Such
operating conditions as cold starting, altitude, acceleration and
deceleration affect input device signals. Based upon signals received,
ECU sends signals to various components which control fuel injection,
ignition timing, idle speed and emission control systems.
INPUT DEVICES
Vehicles are equipped with different combinations of input
devices. Not all input devices are used on all models. To determine

input device usage on specific models, see appropriate wiring diagram
in M - WIRING DIAGRAMS.
Air Conditioner Switch
When A/C is turned on, signal is sent to ECU. With engine at
idle, ECU increases idle speed through Idle Speed Control (ISC) motor.\
Airflow Sensor
Incorporated in airflow sensor assembly, airflow sensor is a
Karmen Vortex-type sensor which measures intake airflow rate.
Intake air flows through tunnel in airflow sensor assembly.
Airflow sensor transmits radio frequency signals across direction of
incoming airflow, downstream of vortex. Intake air encounters vortex,
causing turbulence in tunnel.
Turbulence disrupts radio frequency, causing variations in
transmission. Airflow sensor converts frequency transmitted into a
proportionate electrical signal which is sent to ECU.
Airflow Sensor Assembly
Mounted inside air cleaner, incorporates airflow sensor,
atmospheric pressure sensor and intake air temperature sensor.
Atmospheric (Barometric) Pressure Sensor
Incorporated in the airflow sensor assembly, converts
atmospheric pressure to electrical signal which is sent to ECU. ECU
adjusts air/fuel ratio and ignition timing according to altitude.
Coolant Temperature Sensor
Converts coolant temperature to electrical signal for use by
ECU. ECU uses coolant temperature information for controlling fuel
enrichment when engine is cold.
Crankshaft Angle & TDC Sensor Assembly
Assembly is located in distributor on SOHC engines. On DOHC
engines, which use Direct (or Distributorless) Ignition System (DIS)\
,
assembly is separate unit mounted in place of distributor. Assembly
consists of triggering disc (mounted on shaft) and stationary optical
sensing unit. Camshaft drives shaft, triggering optical sensing unit.
ECU determines crank angle and TDC based on signals received from
optical sensing unit.
Detonation Sensor (Turbo Only)
Located in cylinder block, senses engine vibration during
detonation (knock). Sensor converts vibration into electrical signal.
ECU retards ignition timing based on this signal.
Engine Speed (Tach Signal)
ECU uses ignition coil tach signal to determine engine speed.
Idle Position Switch
On all DOHC engines and Sigma 3.0L, idle position switch is
separate switch mounted on throttle body. On all other models, idle
position switch is incorporated in ISC motor or throttle position
sensor, depending on vehicle application. When throttle valve is
closed, switch is activated. When throttle valve is at any other
position, switch is deactivated. This input from idle position switch
is used by ECU for controlling fuel delivery time during deceleration.
Ignition Timing Adjustment Terminal
Used for adjusting base ignition timing. When terminal is
grounded, ECU timing control function is by-passed, allowing base
timing to be adjusted.

Inhibitor Switch (Automatic Transmission Only)
Inhibitor switch senses position of transmission select
lever, indicating engine load due to automatic transmission
engagement. Based on this signal, ECU commands ISC motor to increase
throttle angle, maintaining optimum idle speed.
Intake Air Temperature Sensor
Incorporated in airflow sensor assembly, this resistor-based
sensor measures temperature of incoming air and supplies air density
information to ECU.
Motor Position Sensor (MPS)
Incorporated in ISC motor (or separate unit on some models),
senses ISC motor plunger position and sends electrical signal to ECU.
Oxygen (O2) Sensor
Located in exhaust system, generates an output voltage.
Output voltage varies with oxygen content of exhaust gas stream. ECU
adjusts air/fuel mixture based on signals from oxygen sensor.
Power Steering Oil Pressure Switch
Detects increase in power steering oil pressure. When power
steering oil pressure increases, switch contacts close, signalling
ECU. ECU commands ISC motor, raising idle speed to compensate for drop
in engine RPM due to power steering load.
TDC Sensor
See CRANKSHAFT ANGLE & TDC SENSOR ASSEMBLY.
Throttle Position Sensor (TPS)
A variable resistor mounted on throttle body. ECU uses
voltage signal received from TPS to determine throttle plate angle.
Vehicle Speed Sensor
Located in speedometer in instrument cluster, uses a reed
switch to sense speedometer gear revolutions. ECU uses gear
revolutions to determine vehicle speed.
OUTPUT SIGNALS
NOTE: Vehicles are equipped with different combinations of
computer-controlled components. Not all components listed
below are used on every vehicle. For theory and operation on
each output component, refer to the system indicated in
brackets after component.
CHECK ENGINE Light
See SELF DIAGNOSTIC SYSTEM.
EGR Control Solenoid Valve
See EXHAUST GAS RECIRCULATION (EGR) CONTROL under EMISSION
SYSTEMS.
Fuel Injectors
See FUEL CONTROL under FUEL SYSTEM.
Fuel Pressure Control Solenoid Valve (Turbo Only)
See FUEL DELIVERY under FUEL SYSTEM.
Fuel Pressure Regulator
See FUEL DELIVERY under FUEL SYSTEM.
Fuel Pump Relay (MPI Control Relay)

See FUEL DELIVERY under FUEL SYSTEM.
Idle Speed Control Servo
See IDLE SPEED under FUEL SYSTEM.
Power Transistor(s) & Ignition Coils
See IGNITION SYSTEMS.
Purge Control Solenoid Valve
See EVAPORATIVE CONTROL under EMISSION SYSTEMS.
Self-Diagnostic Connector
See SELF-DIAGNOSTIC SYSTEM.
Wastegate Control Solenoid Valve
See TURBOCHARGED ENGINES under AIR INDUCTION SYSTEM.
FUEL SYSTEM
FUEL DELIVERY
Electric fuel pump (located in gas tank) feeds fuel through
in-tank fuel filter, external fuel filter (located in engine
compartment) and fuel injector rail.
Fuel Pump
Consists of an impeller driven by a motor. Pump has an
internal check valve to maintain system pressure and a relief valve to
protect the fuel pressure circuit. Pump receives voltage supply from
Multi-Point Injection (MPI) control relay.
Fuel Pressure Control Solenoid Valve (Turbo Only)
Prevents rough idle due to fuel percolation. On engine
restart, if engine coolant or intake air temperatures reach a preset
value, ECU applies voltage to fuel pressure control solenoid valve for
2 minutes after engine re-start. Valve opens, allowing atmospheric
pressure to be applied to fuel pressure regulator diaphragm. This
allows maximum available fuel pressure at injectors, enriching fuel
mixture and maintaining stable idle at high engine temperatures.
Fuel Pressure Regulator
Located on fuel injector rail, this diaphragm-operated relief
valve adjusts fuel pressure according to engine manifold vacuum.
As engine manifold vacuum increases (closed throttle), fuel
pressure regulator diaphragm opens relief valve, allowing pressure to
bleed off through fuel return line, reducing fuel pressure.
As engine manifold vacuum decreases (open throttle), fuel
pressure regulator diaphragm closes valve, preventing pressure from
bleeding off through fuel return line, increasing fuel pressure.
FUEL CONTROL
Fuel Injectors
Fuel is supplied to engine through electronically pulsed
(timed) injector valves located on fuel rail(s). ECU controls amount\
of fuel metered through injectors based upon information received from
sensors.
IDLE SPEED
Air Conditioner Relay
When A/C is turned on with engine at idle, ECU signals ISC

EMISSION SYSTEMS
EXHAUST GAS RECIRCULATION (EGR) CONTROL
Federal (Non-Turbocharged)
To lower oxides of nitrogen (NOx) exhaust emissions, a non-
computer controlled exhaust gas recirculation system is used. EGR
operation is controlled by throttle body ported vacuum. Vacuum is
routed through thermovalve to prevent EGR operation at low engine
temperatures.
Spring pressure holds EGR valve closed during low vacuum
conditions (engine idling or wide open throttle). When vacuum pressure\
increases and overcomes EGR spring pressure, EGR valve is lifted and
allows exhaust gases to flow into intake manifold for combustion.
California & Turbocharged
ECU controls EGR operation by activating EGR control solenoid
valve according to engine load. When engine is cold, ECU signals EGR
control solenoid valve to deactivate EGR.
California models are equipped with an EGR temperature
sensor. When EGR malfunction occurs, EGR temperature decreases and ECU
illuminates CHECK ENGINE (malfunction indicator) light.
EGR Control Solenoid Valve
Denies or allows vacuum supply to EGR valve, based upon ECU
commands.
Thermovalve
Denies or allows vacuum supply to EGR valve based on coolant
temperature.
EVAPORATIVE CONTROL
Fuel evaporation system prevents fuel vapor from entering
atmosphere. System consists of a special fuel tank with vapor
separator tanks (if equipped), vacuum relief filler cap, overfill
limiter (2-way valve), fuel check valve, thermovalve (if equipped),
charcoal canister, purge control valve, purge control solenoid valve
and connecting lines and hoses.
Purge Control Solenoid Valve
When engine is off, fuel vapors are vented into charcoal
canister. When engine is warmed to normal operating temperature and
running above idle, ECU energizes purge control solenoid valve,
allowing vacuum to purge valve.
Canister vapors are then drawn through purge valve into
intake manifold for burning. Purge control solenoid valve remains
closed during idle and engine warm-up to reduce HC and CO emissions.
HIGH ALTITUDE CONTROL (HAC)
This system compensates for variations in altitude. When
atmospheric (barometric) pressure sensor determines vehicle is above
preset altitude, ECU compensates by adjusting air/fuel mixture and
ignition timing. If HAC system is inoperative, there will be an
increase in emissions.
PCV VALVE
Positive Crankcase Ventilation (PCV) valve operates in the
closed crankcase ventilation system. Closed crankcase ventilation

in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Lopes At Intake manifold-to-head Replace manifold
Idle leaks gasket, See ENGINES
Blown head gasket Replace head gasket,
See ENGINES
Worn timing gears, chain Replace gears, chain or
or sprocket sprocket
Worn camshaft lobes Replace camshaft, See
ENGINES
Overheated engine Check cooling system,
See COOLING
Blocked crankcase vent Remove restriction
valve
Leaking EGR valve Repair leak and/or
replace valve
Faulty fuel pump Replace fuel pump









\









\









\









\









\









\









\







Engine Has Low Leaking fuel pump Repair leak and/or
Power replace fuel pump
Excessive piston-to-bore Install larger pistons,
clearance See ENGINES
Sticking valves or weak Check valve train
valve springs components, See ENGINES
Incorrect valve timing Reset valve timing, See
ENGINES
Worn camshaft lobes Replace camshaft, See
ENGINES
Blown head gasket Replace head gasket.
See ENGINES.
Clutch slipping Adjust pedal and/or
replace components, See
ENGINES
Engine overheating Check cooling system,
See COOLING
Auto. Trans. pressure
regulator valve faulty Replace pressure
regulator valve
Auto. Trans. fluid level Add fluid as necessary
too low
Improper vacuum diverter
valve operation Replace vacuum diverter
valve
Vacuum leaks Inspect vacuum system
and repair as required
Leaking piston rings Replace piston rings,
See ENGINES









\









\









\









\









\









\









\







Faulty High Low fuel pump volume Replace fuel pump
Speed Operation
Leaking valves or worn Replace valves and/or
springs, See ENGINES
Incorrect valve timing Reset valve timing,See
ENGINES
Intake manifold restricted Remove restriction
Worn distributor shaft Replace distributor









\









\









\









\









\









\









\







Faulty Improper fuel pump stroke Remove pump and reset
Acceleration pump stroke

Incorrect ignition timing Reset ignition timing,
See TUNE-UP
Leaking valves Replace valves, See
ENGINES
Worn fuel pump diaphragm Replace diaphragm or
or piston piston









\









\









\









\









\









\









\







Intake Backfire Improper ignition timing Reset ignition timing,
See TUNE-UP
Faulty accelerator pump Replace accelerator
discharge pump
Improper choke operation Check choke and adjust
as required
Defective EGR valve Replace EGR valve
Fuel mixture too lean Reset air/fuel mixture,
See TUNE-UP
Choke valve initial Reset choke valve
clearance too large initial clearance









\









\









\









\









\









\









\







Exhaust Backfire Vacuum leak Inspect and repair
vacuum system
Faulty vacuum diverter Replace vacuum diverter
valve valve
Faulty choke operation Check choke and adjust
as required
Exhaust system leak repair exhaust system
leak









\









\









\









\









\









\









\







Engine Ignition timing too far Reset ignition timing,
Detonation advanced See TUNE-UP
Faulty ignition system Check ignition timing,
See TUNE-UP
Spark plugs loose or Retighten or replace
faulty plugs
Fuel delivery system Inspect lines, pump and
clogged filter for clog
EGR valve inoperative Replace EGR valve
PCV system inoperative Inspect and/or replace
hoses or valve
Vacuum leaks Check vacuum system and
repair leaks
Excessive combustion
chamber deposits Remove built-up
deposits
Leaking, sticking or Inspect and/or replace
broken valves valves









\









\









\









\









\









\









\







External Oil Fuel pump improperly seated Remove pump, replace
Leakage or worn gasket gasket and seat
properly
Oil pan gasket broken or Straighten pan and
pan bent replace gasket
Timing chain cover gasket Replace timing chain
broken cover gasket
Rear main oil seal worn Replace rear main oil
seal
Oil pan drain plug not Remove and reinstall
seated properly drain plug
Camshaft bearing drain Remove restriction
hole blocked
Oil pressure sending Remove and reinstall
switch leaking sending switch









\









\









\









\









\









\









\

cracked or broken manifold, See ENGINES








\









\









\









\









\









\









\







ENGINE PERFORMANCE
CARBURETOR TROUBLE SHOOTING:
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC COLD START SYMPTOMS TROUBLE SHOOTING CHART









\









\









\









\









\









\









\







CONDITION POSSIBLE CAUSE CORRECTION








\









\









\









\









\









\









\







Engine Won't Choke not closing Check choke
Start operation, see
FUEL SYSTEMS
Choke linkage bent Check linkage, see
FUEL SYSTEM









\









\









\









\









\









\









\







Engine Starts, Choke vacuum kick setting Check setting and
Then Dies too wide adjust see, FUEL
SYSTEMS
Fast idle RPM too low Reset RPM to specif-
ication, see TUNE-UP
Fast idle cam index Reset fast idle cam
incorrect index, see FUEL
SYSTEMS
Vacuum leak Inspect vacuum
system for leaks
Low fuel pump outlet Repair or replace
pump, see FUEL
SYSTEMS
Low carburetor fuel level Check float setting
see FUEL SYSTEM









\









\









\









\









\









\









\







Engine Quits Choke vacuum kick setting Reset vacuum kick
Under Load incorrect setting,see FUEL
SYSTEMS
Fast idle cam index Reset fast idle cam
incorrect index, see FUEL
SYSTEM
Incorrect hot fast idle Reset fast idle RPM,
speed RPM see TUNE-UP









\









\









\









\









\









\









\







Engine Starts, Choke vacuum kick set too Reset vacuum kick,
Runs Up,Then narrow see FUEL SYSTEMS
Idles, Slowly
With Black Smoke Fast idle cam index Reset fast idle cam