1991 MITSUBISHI MONTERO coolant
[x] Cancel search: coolantPage 671 of 1333
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
COOLANT (PROPYLENE-GLYCOL FORMULATIONS)
CAUTION: To avoid possible damage to vehicle use only ethylene-glycol
based coolants with a mixture ratio from 44-68% anti-freeze.
DO NOT use 100% anti-freeze as it will cause the formation
of cooling system deposits. This results in coolant
temperatures of over 300
\b F (149\bC) which can melt plastics.
100% anti-freeze has a freeze point of only -8\b F (-22\bC).
CAUTION: Propylene-Glycol Mixtures has a smaller temperature range
than Ethylene-Glycol. The temperature range (freeze-boil)
of a 50/50 Anti-Freeze/Water Mix is as follows:
Propylene-Glycol -26
\b F (-32\bC) - 257\b F (125\bC)
Ethylene-Glycol -35\b F (-37\bC) - 263\b F (128\bC)
CAUTION: Propylene-Glycol/Ethylene-Glycol Mixtures can cause the
destabilization of various corrosion inhibitors. Also
Propylene-Glycol/Ethylene-Glycol has a different specific
gravity than Ethylene-Glycol coolant, which will result in
inaccurate freeze point calculations.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
Page 689 of 1333
FUEL SYSTEM PRESSURE RELEASE
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
1) On Colt and Mirage, remove rear seat cushion. On all
models, disconnect fuel pump harness connector at fuel tank.
2) Start engine. Let engine run until it stops. Turn ignition
off. Disconnect negative battery terminal. Connect fuel pump harness
connector.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure from system. See FUEL SYSTEM PRESSURE RELEASE. Raise
vehicle on hoist. Drain fuel into suitable container. Disconnect
electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts
securing fuel tank. Remove fuel tank from vehicle and remove fuel pump
assembly. To install, reverse removal procedure. Tighten nuts to
specification. See TORQUE SPECIFICATION table.
FUEL RAILS & INJECTORS (PFI)
Use a rag to cover fuel hose connection before disconnecting
high pressure fuel hose at fuel rail. Some residual fuel pressure may
still be in system.
Removal (Except Pickup & Ram-50 2.4L)
1) On all models, relieve fuel pressure. See
FUEL SYSTEM PRESSURE RELEASE . Disconnect negative battery cable. On
Montero, Pickup, Ram-50, Stealth and 3000GT 3.0L, disconnect air
intake plenum. On Eclipse, disconnect PCV valve hose.
2) On Colt Vista, disconnect coolant temperature sensor
connector, idle speed control servo connector and brake booster vacuum
hose. On all models, disconnect high pressure fuel hose at fuel rail.
3) Disconnect fuel return hose. Disconnect vacuum hoses. On
Eclipse, Colt and Colt 200, disconnect throttle cable clamp. Remove
center cover. On all models, disconnect injector electrical
connectors. Remove fuel rail bolts and lift fuel rail and injectors
from engine.
Installation
To install, reverse removal procedure. Tighten bolts to
specifications. See TORQUE SPECIFICATIONS table.
Removal (Pickup & Ram-50 2.4L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. On all models,
disconnect air intake hose. Disconnect breather hose (if applicable)
and vacuum hoses.
2) Disconnect coolant lines as necessary for clearance.
Disconnect injector electrical connectors. Position all lines, hoses
and electrical connectors out of way. Disconnect throttle and/or
kickdown cables. Remove throttle body assembly and position it out of
the way.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return line and vacuum line connection at fuel rail.
Remove fuel rail bolts and lift fuel rail and injectors from engine.
Page 690 of 1333
Installation
1) To install, reverse removal procedure. Injectors may be
removed after fuel rail is removed from intake manifold. Use new
insulators and "O" rings when installing injectors.
2) Use spindle oil or gasoline on "O" ring. Install injectors
into fuel rail with a twisting motion. Adjust throttle and kickdown
cable (if applicable). Do not drop injectors while removing or
installing fuel rail.
OXYGEN (O2) SENSOR
Removal & Installation
1) O2 Sensor is mounted in exhaust pipe below exhaust header.
It is equipped with a permanent pigtail which must be protected from
damage when sensor is removed. Ensure sensor is free of contaminants,
avoid using cleaning solvents of any type. Sensor may be difficult to
remove when engine temperature is less than 120
F (48 C).
2) Always use anti-seize compound on threads before
installation. On non-turbo models, remove sensor using Remover
(MD998703). On turbo models, use Remover (MD998748) on Eclipse and
Galant, or Remover (MD998770) on Stealth and 3000GT. Tighten oxygen
sensor to specification. See TORQUE SPECIFICATIONS table.
THROTTLE BODY
Removal
Disconnect air intake hose. Remove accelerator and automatic
speed control cables (if equipped). Disconnect fuel vapor hose,
electrical harness connector, vacuum hose and coolant hoses. Remove
throttle body retaining bolts.
Disassembly
Remove throttle position sensor. Remove idle speed control
motor. Remove throttle bracket and connector bracket (if equipped).
Remove idle position switch and adjusting nut.
NOTE: DO NOT remove throttle valve. DO NOT use cleaning solvents
on throttle position sensor, idle speed control motor or
idle position switch.
Cleaning
Clean all parts except those noted in solvent. Check vacuum
port and passage for clogging. Clean vacuum, vapor and fuel passages
with compressed air.
Reassembly
To reassemble, reverse disassembly procedure.
Installation
To install, reverse removal procedure.
THROTTLE POSITION SENSOR/SWITCH
Removal & Installation
Throttle position sensor/switch is located on throttle body.
Disconnect TPS electrical connector. Remove bolts holding TPS and
remove TPS. To install, reverse removal procedure. Tighten throttle
position sensor/switch to specification. See TORQUE SPECIFICATIONS
table. For adjustment procedure, see ON-VEHICLE ADJUSTMENTS article.
TURBOCHARGERS
Page 691 of 1333
NOTE: Removal of turbocharger exhaust housing and water pipes at
turbocharger is not necessary when removing turbocharger
assembly. Stealth and 3000GT models have 2 (front and rear)
turbochargers.
Removal (Eclipse & Galant)
1) Disconnect negative battery cable. Drain engine coolant
and oil. On models with A/C, remove condenser fan motor assembly. On
all models, remove oxygen sensor. Remove oil dipstick guide and "O"
ring. See Figs. 8 and 9.
Fig. 8: Removing Turbocharger (Eclipse & Galant 2.0L)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 9: Exploded View of Turbocharger Assembly (Eclipse & Galant
2.0L Shown; Stealth & 3000GT Similar)
Page 692 of 1333
Courtesy of Mitsubishi Motor Sales of America.
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect coolant hose and tubes. Remove nuts and bolts
securing exhaust manifold. Remove exhaust manifold and gaskets.
Disconnect oil return pipe. Remove turbocharger assembly.
Removal (Stealth & 3000GT Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove alternator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect oxygen sensor electrical
connector. Remove oil return pipe. Remove turbocharger support bracket
and remove turbocharger from exhaust manifold. See Fig. 10.
Fig. 10: Removing Front Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Removal (Stealth & 3000GT Rear)
1) Disconnect battery cables and remove battery. Drain engine
oil and coolant. Remove accelerator cable. Remove air hose, air pipe
and heat protectors. Disconnect clutch booster vacuum hose. Remove air
Page 693 of 1333
intake hoses and EGR pipe. Disconnect oxygen sensor electrical
connector.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly. See Fig. 11.
Fig. 11: Removing Rear Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
Check turbine and compressor wheels for cracking and other
damage. Make sure turbine and compressor wheels turn smoothly. Check
for oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See SYSTEM & COMPONENT TESTING article.
Installation
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger. Ensure oil and air hoses are properly installed and
securely clamped.
2) Use new gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Fuel Tank Nuts ............................. 15-22 (20-30)
Page 705 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels](/manual-img/19/57332/w960_57332-704.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels")
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)
Page 707 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\](/manual-img/19/57332/w960_57332-706.png "MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\")
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature