1991 MITSUBISHI 3000GT fuel

II-18ENGINE - Engine Assembly
19. ISC servo connector
20. TPS connector
21. Oil pressure switch and oil
pressure gauge unit connector22. Fuel injector harness connector
23. Knock sensor connector
24. Crankshaft angle sensor connector
25. Engine coolant temperature
switch connector (Air conditioner)
26. Engine coolant temperature
sensor connector
27. Engine coolant temperature
gauge unit connector
28. Condenser connector
29. Ignition coil connector
30. Power transistor connector
31. Fuel injector connector
32. Variable induction motor connector

33. Oxygen sensor connector 28
2930lOO-
120 Nm72 - 87 ft.lbs.
70 Nm
,51 ftlbs
** l * 34. Engine mounting bracket
35. Rear roll stopper bracket and engine
connection bolt36. Front roll stopper bracket and engineconnection bolt** l a 37. Engine assembly35 Nm
25 ft.lbs.
?I,---R
50-60 Nm36 - 43 ftlbs.
OlFOO19
TSB Revision

11-32ENGINE - Rocker Arm and Camshaft
r
I
/7EN024E
Small wire
8ENOO58
Identification mark(stamped on hexagon section)
7EN0249
Front sideINSPECTION
MllZCAB
CAMSHAFTMeasure cam height (longer diameter of the cam). If it exceeds
the limit, replace the camshaft.
Standard value:
Intake side
35.49 mm (1.3972 in.)
Exhaust side
35.20 mm (1.3858 in.)
Limit:
Intake side
34.99 mm (1.3776 in.)
Exhaust side
34.70 mm (1.3661 in.)SERVICE POINTS OF INSTALLATION
MllZDAK
11. INSTALLATION OF LASH ADJUSTER
(1) Immerse the lash adjuster in clean diesel fuel.
(2) Using a small wire, move the plunger up and down 4 or
5 times while pushing down lightly in the check ball in
order to bleed out the air.
(3) Install the lash adjuster to the cylinder head.
9. INSTALLATION OF CAMSHAFT
(1) Turn the crankshaft to bring No.1 cylinder to the top
dead center.
(2) Check that the rocker arm is installed correctly on the
lash adjuster and valve.
(3) Install the camshaft noting the identification mark
(stamped on the hexagon sectioned).
Identification mark: Intake sideV
Exhaust side C
(4) Install the camshafts with their dowel pins positioned
as shown in the illustration.
Rear side ,
Approx. 100”
Pl
Frontm&k
M
0
/
Cap No
TSB Revision
Identificationmark
7EN03168. 7. 6. 4. 2. INSTALLATION OF BEARING CAPS
(1) Install noting the identification mark and cap No. No.2, 3
and 4 bearing caps bear the front mark. Install these
caps with the mark lined up with the front mark on the
cylinder head.
Identification mark: Intake side
IExhaust side E

FUEL
SYSTEM
CONTENTSM13AA- _
CRUISE CONTROL SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . .158SPECIFICATIONS. . . . . . . .._._....................................................155
CRUISE CONTROL SYSTEM*................................................185
SERVICE ADJUSTMENT PROCEDURES............................178
Cruise Control Cables Inspection and Adjustment........178Cruise Control SystemInspection....................................179individual Parts Inspection....................................................181
SPECIAL TOOLS........................................................................159
SPECIFICATIONS....................................................................158
General Specifications........................................................158Service Specifications........................................................158
TROUBLESHOOTING............................................................159
Check Chart............................................................................163Harness and Components Layout....................................176Preliminary Inspection........................................................159Self-diagnosis Checking........................................................172Troubleshooting Quick Reference Chart............................159
ENGINE CONTROL............................................155
ENGINE CONTROL................................................................157
SERVICE ADJUSTMENT PROCEDURES............................156
Accelerator Cable Inspection and Adjustment................156Accelerator Switch Inspection and Adjustment................156
Service Specifications........................................................
155
TROUBLESHOOTING............................................................
155
Accelerator Cable and Accelerator Pedal........................155
FUEL SYSTEM....................................................3
DETONATION SENSOR........................................................154
FUEL FILTER............................................................................
153
FUEL LINE AND VAPOR LINE................................................151
FUEL PUMP AND FUEL GAUGE UNIT ASSEMBLYAND OVERFILL LIMITER (TWO-WAY VALVE)................149
FUEL TANK.................................................................................146
GENERAL INFORMATION
....................................................
3
MPI System Diagram............................................................3
INJECTOR................................................................................141
ON-VEHICLE INSPECTION OF MPI COMPONENTS........36
Active Exhaust Control Unit ............................130Air Conditioner Switch and Power Relay............................82Air Flow Sensor....................................................................54Anti-lock Brake Signal ........................................133Barometric Pressure Sensor................................................60CONTINUED ON NEXT PAGE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(I)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP
528 -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

13-2
Boost Meter ........................................................128Components Inspection Procedure....................................40
Components Location........................................................36
Crank Angle Sensor
............................................................72Detonation Sensor................................................................84EGR Control Solenoid Valve
........................................121
EGR Temperature Sensor ............................92ElectricalLoad Switch........................................................86Engine and Transaxle Total Control Signal ............135Engine Control Unit Power Ground....................................44Engine Coolant Temperature Sensor................................62Fuel Pressure Control Valve ............................123Fuel Pressure Test................................................................138Fuel Pump ....................................................45Fuel Pump ............................................................48
Fuel Pump Operation Check................................................137Fuel Pump Relay No. 2........................................................53Fuel Pump Resistor............................................................53
Idle Position Switch............................................................68Idle Speed Control Servo (Stepper Motor Type)............1 IOIgnition Coil and Power Transistor....................................115Ignition Switch-ST and Inhibitor Switch ................76Ignition Switch-ST ................................................75Induction Control Valve Position Sensor
........................................................................90
Injectors........................................................101Injectors................................................................105Intake Air Temperature Sensor............................................57Muffler Mode Changeover Switch ....................88Oxygen Sensor ............................................
94
Oxygen Sensor ....................................................98
Power Steering Oil Pressure Switch................................80Power Supply and Ignition Switch-IG................................41
Purge Control Solenord Valve............................................1 19Release of Residual Pressure from High
Pressure Fuel Hose............................................................137Throttle Position Sensor....................................................65Top Dead Center Sensor....................................................70Variable Induction Control Servo (DC Motor)
........................................................................131Vehicle Speed Sensor........................................................78Waste Gate Control Solenoid Valve ................126
SERVICE ADJUSTMENT PROCEDURES............................31
Adjustment of Fixed SAS....................................................35Adjustment of Idle Position Switch and
Throttle Position Sensor (TPS)............................................33Basic Idle Speed Adjustment............................................31Throttle Body (Throttle Valve Area) Cleaning....................33
SPECIAL TOOLS........................................................................8
SPECIFICATIONS
....................................................................6
General Specifications........................................................6Sealant....................................................................................7Service Specifications........................................................7
THROlTLE BODY....................................................................143
TROUBLESHOOTING............................................................9
Check Chart Classified by Problem Symptoms................16Circuit Diagram....................................................................18Engine Warning Light (Malfunction Indicator Light)........11Explanation and Cautions about Harness Check............10Explanation of Troubleshooting Procedures....................9Fuel Tank and Fuel Line........................................................30
Problem Symptoms Table (For Your Information)............17Self-diagnosis........................................................................12)
I

FUEL SYSTEM - General Information
FUEL SYSTEM
L/ GENERAL INFORMATION
MPI SYSTEM DIAGRAM -Non Turbo>4,xwo3 ,elOl alxesueJl/aulfiu~
*1qt% 6uluJeMaul6u~,!03 u0yJ61EIc84hqa dwnd ,an,hew XVzONaS ,on”o5 “ownp”! a,qe!Je/\ECan,&, ~lo”a,os ,0~1”03 a6md&S
mJaS XI
TSB Revision

EUT
E”‘X 0S@‘u,E%.$gg
g 26;_I
P
5 ash
\
13-4FUEL SYSTEM - General Information
-
tI
:‘iEI-2
Ln030-l03LLr?
TSB Revision

FUEL SYSTEM - General Information
13-5

,-=c1 ,ivYan,w p1oYa,os am aSeMawn ploqor ,Oli”OJ aE%:an,en,Oll”OJ amrsa>* WI,‘6.XONar 3SIiI=5
i-
an,en plo”apn ,Ol,“rn 833
r
IIIII III 1
II
I J
b
-ti.=z wf aa.5 239
B5:
::KplyPB
I
I,$L1 gE:;I$$I:
TSB Revision

Tank capacityliter (gal.)
Return system
Filter
High pressure type
Electrical, in-tank type
Driven by
Throttle position sensor
idle speed control servoVariable resistor type
Stepper motor typeThe stepper motor type by-pass air controlsystem with the first idle air valve
Engine control unit
Identification model No.
Federal

California
Karman vortex type
Barometric pressure
sensorSemiconductor diffusion type
Engine coolant temperature sensor
Oxygen sensor
Vehicle speed sensor
Detonation sensor
Top dead center sensor
Crank angle sensor
Induction control valve position sensor
EGRtemperature sensor Reed switch type
Piezoelectric device type
Photo interrupter type
Photo interrupter type
Variable’resistor type
13-6FUEL SYSTEM - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
TSB Revision