1991 MITSUBISHI 3000GT brake sensor

CRUISE CONTROL SYSTEM - Service Adjustment Procedures13-183
onoo5J16LO285
141014;
TFA0359
16FO13LResistance
3--1Okl2
STOP LIGHT SWITCH/BRAKE SWITCH INSPECTION(1) Disconnect the connector.
(2) Check for continuity between the terminals of the switch.
O-O: Continuity
Brake switchStop light switch
1423
Whenbrakepedal00depressed.
When
brake
pedal00not depressed.CLUTCH SWITCH INSPECTION
(I) Disconnect the connector.
(2) Check that there is continuity between the terminals when
the clutch pedal is depressed, and that there is no
continuity when the pedal is released.
INHIBITOR SWITCH (“N” POSITION) INSPECTION
(1) Disconnect the connector.
(2) Check to be sure that there is continuity between connec-
tor terminals
@and @when the shift lever is moved to the
“N” range.
VEHICLES SPEED SENSOR INSPECTION
Use circuit tester to check circuit repeats off/on between
terminals when speedometer shaft turned several times.

(1) Remove the vehicle’s speed sensor and connect as shown
in the illustration, using a 3
- 10 kQ resistance.
(2) Use a voltmeter to check for voltage at terminals @ and @
when the pulse generator shaft is turning. (One revolution
is four pulses.)
16R0273
TSB Revision

INTAKE AND EXHAUST - Air Intake Plenum 15-13
AIR INTAKE PLENUM
/REMOVAL AND INSTALLATIQNMlWA-B
L/
i
I Post-installation ODeration
Adjustment of Accelerator Cable
(Refer to GROUP 13 - Engine Control.)
Removal steps7-9ft.lbs.
I. Connection air intake hose2. Connection of accelerator cable_*I)3. Throttle body assemblyl *4. Throttle body gasket
5. Connection of brake booster vacuum hose
6. Harness connecters8 60Nm;6Nm05FOO32
43 ft.lbs.13 ft.lbs.
7. Connection of VIC servo motor
8. EGR pipe
9. EGR valve California>
11. EGR temperature sensor
12. Accelerator cable bracket
13. Connection of air intake plenum stay14. Air intake plenum installation bolts
15. Air intake plenum installation nuts
16. Air intake plenum
17. Air intake plenum gasket
Throttle body
SERVICE POINT OF REMOVALM15UBC23. REMOVAL OF THROTTLE BODY ASSEMBLY
Leaving the water hoses and vacuum hoses in their
installed positions, remove from the air intake plenum.
INSPECTIONM15UCAD2
Check the following points; replace the part if a problem is
found.
AIR INTAKE PLENUM
(1) Check air intake plenum for defect or cracks. Replace if
defective or cracked.
(2) Check load (negative pressure) of drain port. Clean if
required.
SERVICE POINT OF INSTALLATIONMl5UDAB2
4. INSTALLATION OF THROTTLE BODY GASKET
Install with the gasket protrusion positioned as shown.
CautionIf installed in an incorrect direction, idling failure or
other problems may occur.
TSB Revision

15-14INTAKE AND EXHAUST - Air Intake Plenum
AIR INTAKE PLENUM MIBUA-C
REMOVAL AND INSTALLATION
(Refer to GROUP 13 - Engine Control.)
/TurbochargerO&gOSFOOOS5Nm
L
18 Nm18
19 Nm13 ft.lbs.
-05FOO31Removal steps
I. Connection.air hose A2. Connection of accelerator cablea*3. Throttle body assemblyl *4. Throttle body gasket
5. Air pipe A
6. Connection of vacuum hose
7. Connection of brake booster vacuum hose
8. Harness connecter
9. Connection of clutch booster vacuum hose
10. EGR temperature sensor California>
11. EGR valve
12. EGR valve gasket
13. EGR pipe installation bolts
14. EGR pipe gasket
15. Connection of air intake plenum stay
16. Air intake plenum installation bolts
17. Air intake plenum installation nuts
18. Air intake plenum
19. Air intake plenum gasket
SERVICE POINT OF REMOVALM15UBAU3. REMOVAL OF THROTTLE BODY ASSEMBLY
Leaving the water hoses and vacuum hoses in their
installed positions, remove from the air intake plenum.
TSB Revision

23-1
AUTOMATIC
TRANSAXLE
CONTENTSMZJAA- _
ANNULUS GEAR AND TRANSFER DRIVE GEARTransmission Fluid Level Inspection................................46SET................................................................................................
102Transmission Fluid Replacement........................................
46
DIFFERENTIAL........................................................................104SPECIAL TOOLS........................................................................
16
:......................................... 12IEND CLUTCH ASSEMBLY....................................................99SPECIFICATIONS..........................
FRONT CLUTCH ASSEMBLY................................................95
GENERAL INFORMATlON....................................................2
KICKDOWN SERVO................................................................
107
LOW-REVERSE BRAKE............................................................
107
OIL PUMP....................................................................................93
PLANETARY GEAR................................................................
100
REAR CLUTCH ASSEMBLY....................................................97
SELECTOR LEVER ASSEMBLY............................................58
SERVICE ADJUSTMENT PROCEDURES............................46
Accelerator Switch
Inspection and Adjustment................
50Drive Shaft Oil Seals Replacement....................................
52Inhibitor Switch and Control Cable Adjustment................
52Key Interlock Mechanism Check........................................50KickdownServo Adjustment................................................
47Line Pressure Adjustment....................................................
48Reducing Pressure Adjustment........................................
49Selector Lever Operation Check........................................
50Shift Lock Mechanism Check............................................51Speedometer Cable Replacement....................................53
General Specifications........................................................12Lubricants............................................................................15Service Specifications........................................................12Spacer and Snap Ring........................................................13Valve Body Spring Identification Chart............................13
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................106
TRANSAXLE ASSEMBLY........................................................62
TRANSAXLE CONTROL*........................................................54
TRANSAXLE OIL COOLER, HOSES, TUBES
....................66
TRANSFER SHAFT....................................................................92
TROUBLESHOOTING............................................................
19
A/T Safety-lock System Troubleshooting........................44Converter Stall Test............................................................
43
Diagnosis and Test
................................................................
22
Element in Use at Each Position of Selector Lever........31Inspection
of ControlSystem............................................
28Inspection of Electronic Control System Components....32Oil Pressure Tests................................................................
39ShiftPatterns....................................................................
31,42Troubleshooting Guide........................................................
20
VALVE BODY. . . .._._.................................................................... 108
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3668GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to beremoved/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead topersonal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
(3) MlTSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B -Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the
ISRS or any SRS-related component.

AUTOMATIC TRANSAXLE - Troubleshootincl23-19Based upon use of the troubleshooting
Checks should be made of fluid levels and
the condition of the ATF, as well as the
condition of the manual control cables;
adjustments should then be made if found
to be necessary.
If a presumption has been made that there
is an abnormal condition somewhere in
the electronic-control system, check the
fault code, in order to determine the
probable location of the problem, by using
a multi-use tester or voltmeter.
I
When the abnormal system is discovered,
check each element (sensors, etc.) one by
one, and make repairs as necessary.
IWhen the abnormal condition is presumed
to be in the oil-pressure-control system
When the result of the oil-pressure test
does not satisfy the specified pressure,
check each system at places related to the
valve body, check the oil-pressure pas-
sages for leakage, etc.
I
If the problem isunusually dirty ATF,
abnormal noises, oil leakage, or slippage of
the clutch or brakes, or an abnormal
condition of the transaxle itself, disassem-
ble and repair the transaxle.
TROUBLESHOOTINGM23EEAYFunctional malfunctions of the ELC4A/T can lead to other
problems, such as those described below:(I
) Improper maintenance and/or adjustments
(2) Malfunctions of the electronic control functions
(3) Malfunctions of mechanical functions
(4) Malfunctions of hydraulic control functions
(5) Malfunctions of engine performance
etc.
In order to properly determine (“Troubleshoot”) the source of
these malfunctions, it is first essential to methodically question
the user concerning the details of the problem, such as the
condition of the problem, the situation at the time the problem
occurred, and any other relevant information, all in as much
detail as possible. The user should also be asked whether or
not the problem has occurred more than once, and under what
conditions.
Subsequently, certain tests should be conducted in a certain
order, as described at the left.
TSB Revision

23-48AUTOMATIC TRANSAXLE - Service Adjustment Procedures
Adjusting screw4
or~0\====m00~7/IIIITFAm
c-1
Pi(8) Tighten lock nut by hand until it contacts piston. Then, using
torque wrench, tighten to specification.
Lock nut: 29 Nm (21
ftlbs.)Caution
Use of socket wrench or torque wrench could result in
lock nut being turned with adjust rod.
(9) Remove the special tool to secure the piston and torque
plug to specification at L/R brake pressure take-up port.
LINE PRESSURE ADJUSTMENT
(I) Discharge AFT.
(2) Remove oil pan.
(3) Remove oil filter.
(4) Remove oil temperature sensor.
M23FSAC(5) Press solenoid valve harness grommet catch to push in
grommet; then, remove valve body assembly.
Caution
Do not let manual valve fall.
(6) Turn adjusting screw of regulator valve to obtain the
specified line pressure
(K/D brake pressure).
Standard value:870
- 890 kPa (124 - 127 psi)
Oil pressure change for
each turn of adjustment screw:38
kPa (54 psi)
(7)Check that an O-ring is fitted at the location shown on top off
valve body.
(8) Replace O-ring of solenoid valve intermediate grommet
with a new one and then fit the O-ring into case.6
TSB RevisionI

AUTOMATIC TRANSAXLE - Service Adjustment Procedures23-49
1(9) Install valve body and oil temperature sensor.
Bolt A
= Length 18 mm (.709 in.)
Bolt B
= Length 25 mm (.984 in.)
Bolt C
= Length 40 mm (1.575 in.)
CautionSecure solenoid valve and oil temperature sensor
harness at locations shown.
(1O)lnstall oil filter.(1l)lnstall new oil pan gasket and oil pan.
(12)Add the specified amount of ATF.
(13)Carry out hydraulic test.
Readjust as necessary.
REDUCING PRESSURE ADJUSTMENTh323FfADWhen multi-use tester is not used
(1) Following the same steps as those in line pressure
adjustment, remove parts up to oil filter.
There is no need to remove valve body.
(2) Turn adjusting screw of lower valve body to obtain the
specified reducing pressure. Turn it counterclockwise to
increase the pressure.
Standard value:425 f 10 kPa (60 f 1 psi)
Oil pressure change for
each turn of adjusting screw:45 kPa (6 psi)(3) In the same way as in line pressure adjustment,
/nstall oil
filter and oil pan.
(4) Perform hydraulic test.
Adjust as necessary.
When multi-use tester is used
(1) Adjust to obtain the specified K/D brake pressure when PC
solenoid is energized at duty 50% with the multi-use tester.
Standard value:275 kPa (39 psi)
Oil pressure change for
each turn of adjusting screw:50 kPa (7 psi)(2) After adjustment has been made, check that the recuding
pressure is in the range 360
- 480 kPa (51 - 68 psi).
Caution
This adjustment should be made with oil temperature70
- 80°C (160 - 180°F).
The adjustment made with high oil temperature couldresult in improper adjustment due to a line pressure
drop at idle.
TSB Revision

i
LJ
AUTOMATIC TRANSAXLE - Transaxle Assembly
DISASSEMBLY AND REASSEMBLY23-65
M23LEAN
11
Z:4.
::
;:9.10.11.
12.
13.
14.
15.
16.8
%&,kd!~~ / I!- 1A8 ii9
-114Torque converter~.I~I~~~ assembly
Thrust washer
#IFront clutch assembly
Thrust race #3
Thrust bearing #4Thrust washer #2Rear clutch assemblyThrust bearing #5Rear clutch hubThrust race #6Thrust bearing #7Kickdown bandKickdown drumSnap ring
17.Center support18.Wave spring19.Return spring
20.Pressure plate21.Brake disc
22.Brake plate
23.Reaction plate
24. Reverse sun gear
25. Thrust bearing #8
26. Thrust race #927. Forward sun gear
28. Planetary carrier asseml
29.Thrust bearing #I030.Output flange
31. Oil level gauge
32. Oil filler tube33.Snap ring34. Kickdown servo switch35.Snap ring26
25
24
TFA040936.
Kickdown servo piston37.Spring
38.Anchor rod39.Detent assembly
40. Manual control shaft
41. Parking roller support
42.Oilpan43.Gasket44. Oil temperature sensor45.Oil screen46. Valve body assembly
47. Manual control lever
48.Inhibitor switch
49. End clutch shaft
50.Bearing retainer51.Thrust bearing #I1
52. End clutch hub53.Thrust washer
54. End clutch assembly
55.O-ring56. End clutch cover57.Pulse generator
58:Lock bolt
59.Idler shaft
60.Idlergear
61.Spacer
62.Gasket
TSB Revision