1991 MITSUBISHI 3000GT service

22-42MANUAL TRANSAXLE - Shift Rails and Forks
SHIFT RAILS AND FORKSMZZMLAF
DISASSEMBLY AND REASSEMBLY
7-5i-s
Disassembly steps
1.1st-2ndspeedshiftfork2.1st-2ndspeedshiftrail3. 3rd4th speed shift fork
4. 5th-reverse speed shift raill a5. Interlock plunger
6. 3rd-4th speed shift rail
7. Reverse shift lug
201073
InterlockReverse shift lugSERVICE POINT OF REASSEMBLY5. INSTALLATION OF INTERLOCK PLUNGER
Insert the interlock plunger at illustrated position of the
3rd-4th speed shift rail.
TSB Revision

MANUAL TRANSAXLE - Differential Assembly22-43
DIFFERENTIAL ASSEMBLY
IDISASSEMBLY AND REASSEMBLY
Disassembly steps
** 1. Bolt2. Differential drive gear** *+3. Taper roller bearingl * l +4. Lock pinl *5. Pinion shaftl * 6. Pinion
l * 7. Washer
** 8. Side gearl *9. Spacer (Select)10. Differential caseTFM0054
/Adhesive: 3M Stud Locking- . .] _PartNo.417Ooreqr
130-i40Nnl94- 101 ft.lbs.
Press
ti Bearmg
SERVICE POINTS OF DISASSEMBLY
3. REMOVAL OF TAPER ROLLER BEARING
Remove the taper roller bearing using the special tool as
illustrated.
Caution1. Do not reuse the bearing removed from the dif-
ferential case.
2.Replace the inner and outer races of the taper rollerbearing as a set. ,
TSB Revision

22-44MANUAL TRANSAXLE - Differential Assembly
Lock pin
Pinion shaft
2 150020160124
Differen-ock pinend with4. REMOVAL OF LOCK PIN
Drive out the lock pin from the hole A using a
punch.
:,,)
SERVICE POINTS OF REASSEMBLY9. INSTALLATION OF SPACER
/ 8. SIDE GEAR / 7.
WASHER
/ 6. PINION / 5. PINION SHAFT
(I 1 Install the spacer on the back of the side gear and theninstall the gear in the differential case.
CautionWhen installing a new side gear, use a spacer of
medium thickness
[0.93 - 1.00 mm (.036 - .04 in.)].
(2) Set the washer on the back of each pinion and insert the
two pinions to specified position while engaging themwith the side gears and turning them.
(3) Insert the pinion shaft.
(4) Measure the backlash between the side gears and
pinions.Standard value: 0.025
- 0.150 mm (.OOl - .006 in.)
(5) If the backlash is out of specification, disassemble againand using correct spacer, reassemble and adjust.
CautionAdjust for same backlash of both side gears.
4. INSTALLATION OF LOCK PIN
Align the pinion shaft lock pin hole with the case lock pin
hole and insert the lock pin.
Caution1. Do not reuse the lock pin.
2. The lock pin head must be sunk from the flange
surface of the differential case.
TSB Revision1

MANUAL TRANSAXLE Differential Assembly / Speed-
- ometer Driven Gear Assembly22-45
TFYOO4Q
The numerals @to @ indicate
the tightening sequence.
9
SPEEDOMETER DRIVEN GEAR ASSEMBLY
DISASSEMBLY AND REASSEMBLY
3. INSTALLATION OF TAPER ROLLER BEARINGInstall the taper roller bearings on both sides of the
differential case.
CautionWhen press-fitting the bearings, push the inner race
only.
1.INSTALLATION OF BOLTS
Apply specified adhesive to the entire threads of the bolts
and quickly tighten in the order shown to specified torque.
Specified adhesive: 3M Stud Locking Part No. 4170 or
equivalent
CautionIf a bolt is reused, remove traces of oil adhesive
completely from the threads.MZ2MNAE
Disassembly steps
I. O-ringl *2. Spring pin
l *3. Speedometer driven gear4. Oil seal
5. Sleeve201078
201075
SERVICE POINTS OF REASSEMBLY3. INSTALLATION OF SPEEDOMETER DRIVEN GEAR
Apply gear oil sparingly to the speedometer driven gear
shaft and insert the shaft.
2. INSTALLATION OF SPRING PIN
Install the spring pin in such a way that its slit does not facethe gear shaft.
J
TSB RevisionI

MANUAL TRANSAXLE - Clutch Housing Assembly22-47
1
Oil sealSocketwrench
SERVICE POINTS OF DISASSEMBLY6. REMOVAL OF LOCK PIN
Drive out the lock pin from the control finger using the pin
punch.
CautionWhen removing the lock pin, turn the control lever to
such position that the lock pin will not contact the
clutch housing.7. REMOVAL OF SPRING PIN
Drive out the spring pin from the stopper body using the pin
punch.
Caution
When removing the spring pin, pull the control shaft inthe direction illustrated so that the spring pin will not
contact the clutch housing.
SERVICE POINTS OF REASSEMBLY
17.16. INSTALLATION OF NEEDLE BEARINGSInstall the needle bearing flush with the surface A of the
clutch housing.
15. INSTALLATION OF OIL SEALInstall the control shaft oil seal using a socket wrench.
7. INSTALLATION OF SPRING PIN
/ 6. LOCK PIN
(I) Install new spring pin and lock pin using the special tool.
CautionDo not reuse the spring pin and lock pin.
(2) Install the spring pin with its slit at right angle to the
control shaft center.
TSB Revision

MANUAL TRANSAXLE - Service Adjustment Procedures22-51SERVICE ADJUSTMENT PROCEDURES
TRANSMISSION OIL LEVEL INSPECTIONM22FBAE2
Refer to GROUP 00
- Maintenance Service.
TRANSMISSION OIL REPLACEiVlENTMUFCAJ
(I) Position vehicle on a flat level and remove filler and drainplugs to drain transmission oil.
(2) Pour in fresh transmission oil through filler port.
Transmission oil: Hypoid gear oil, SAE 75W-85W con-
forming to API classification GL-4 or
higherTransaxle: 2.4 liters (2.5 qts.)
Transfer: 0.27 liters
(.29 qts.)
(3) After checking to be sure that the oil level is the specifiedlevel, tighten the filler plug at the specified torque.
1 TSB Revision

22-52 MANUAL TRANSAXLE - Service Adjustment Procedures
DRIVE SHAFT OIL SEALS REPLACEMENTMZZFDAJ)(I) Disconnect the drive shaft from the transaxle.
(Refer to GROUP 26
- Drive Shaft.)
(2) Remove the transfer assembly.ij(3) Using a flat-tip
(-) screwdriver, remove the oil seal.
L.H. side\
For L.H.
Dust seal.
For R.H.(4) Install the oil seals using the following procedure:Using the special tool, tap the oil seal into the transaxle.
Note that there are two types of oil seals, one for R.H. and
the other for L.H., and the shape of each type is different,
as shown.
(5) Drive shaft
011 seal must be installed in the direction shown.(6)
$4~1~ a coatrng of the transmission oil to the lip of the oil
Transmission oil: Hypoid gear oil, SAE
75W-90 or
75W-85W conforming to API classi-fication GL-4 or higher
wision

MANUAL TRANSAXLE -Service Adjustment Procedures / Shift Lever Assembly22-53
Front exhaust p6eU.09FOO64
& MD998304-01
LJ -3 ‘=-----XL I
TRANSFER OIL SEAL REPLACEMENTMUFGAH
(1) Pull out the propeller shaft from the transfer. (Refer to
GROUP 25 - Propeller Shaft.)
(2) Using a flat-tip (-) screwdriver, remove the oil seal.
(3) Using the special tool, tap the drive shaft oil seal into the
transfer.
(4) Apply a coating of the transmission oil to the lip of the oil
seal.Transmission oil: Hypoid gear oil, SAE
75W-90 or
75W-85W conforming to API classi-.
fication GL-4 or higher
SPEEDOMETER CABLE REPLACEMENTMZ2FEAH
Refer to
P.22-9.
SHIFT LEVER ASSEMBLYRefer to
P.22-13.M22GE-B
TSB Revision