1991 MAZDA MIATA electrical

Fig. 4: Identifying Alternator Terminals (1992 All Other Models)
Courtesy of MAZDA MOTORS CORP.
2. If output amperage is not equal to or more than amount specified in ALTERNATOR OUTPUT table,
repair or replace alternator as necessary.
3. Turn off all accessories and release brake pedal. With engine operating at 2500-3000 RPM, measure
output amperage. If output amperage is not at least 5 amps, repair or replace alternator as necessary.
4. With engine operating at 2500-3000 RPM, measure voltage between terminal "S" and ground. If reading
is not 14.1-14.7 volts, repair or replace alternator as necessar
y.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.

ALTERNATOR OUTPUT
BENCH TESTING
Rectifier/Diode Assembly
1. Using an ohmmeter, check continuity of each diode in both directions (polarity). See Fig. 5 and Fig. 6. If
diode shows high resistance in one direction and low resistance in other direction, diode is okay.
2. If diode shows low resistance in both directions, it is shorted. If diode shows high resistance in both
directions, diode is open. If an
y diode is defective, replace rectifier assembly.
ApplicationAmps
B220055
B2600i60
Miata
A/T65
M/T60
MPV70
MX-6 & 626
Non-Turbo70
Turbo
A/T80
M/T70
MX-3
4-Cylinder70
V690
Protege & 32365
RX780
92970

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

Fig. 5: Testing Alternator Rectifier & Diodes
Courtesy of MAZDA MOTORS CORP.
Fig. 6: Testing Alternator Rectifier & Diodes (1992)

Courtesy of MAZDA MOTORS CORP.
Rotor & Slip Rings
Measure resistance between rotor slip ring contacts. See Fig. 7 . If resistance is not within specification, replace
rotor. See ROTOR RESISTANCE SPECIFICATIONS table. Check continuity between individual slip rings
and rotor core/shaft. If there is continuit
y, replace rotor.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 9 © 2005 Mitchell Repair Information Company, LLC.

Fig. 7: Testing Alternator Stator, Rotor & Brushes
Courtesy of MAZDA MOTORS CORP.
ROTOR RESISTANCE SPECIFICATIONS
Stator
Check continuity between stator coil leads and stator core. See Fig. 7 . If there is continuity, replace stator.
Check continuity between leads of stator coil. If there is no continuity, replace stator.
Brushes
Replace brushes if worn to limit line. See Fig. 7 . Replace brush springs if corroded. For brush replacement
procedure, see OVERHAUL.
OVERHAUL
DISASSEMBLY
1. Place a 200-watt soldering iron against rear bearing for 3-4 minutes to heat rear cover to 122-140°F (50-
60°C). Carefull
y separate front case and rotor from rear cover and stator. See Fig. 8 , Fig. 10and Fig. 11.
ApplicationOhms
MPV2.7-2.9
RX72.0-4.0
All Others3.5-4.5

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 10 © 2005 Mitchell Repair Information Company, LLC.

Fig. 8: Overhauling Alternators
Courtesy of MAZDA MOTORS CORP.
2. Position rotor in vise. Remove pulley. Disassemble pulley, rotor and front case. Remove front bearing
from front case. Using a bearing puller, remove rear bearing.
3. Remove "B" terminal nut and bushing from rear cover. Remove screws from brush holder and rectifier.
Separate rear cover and stator. When unsoldering rectifier and stator leads, disconnect as quickly as
possible (5 seconds maximum) to avoid damage to rectifier. To remove brushes from holder, unsolder
pigtail from terminal.
REASSEMBLY
Brush Installation
1. Install brush and spring into holder. Allow brush to extend out of holder until wear limit line extends .08-
.16" (2-4 mm) beyond end of brush holder. See Fig. 9
. Solder pigtail onto brush holder.
2. Insert spring and brush into brush holder. Using a spring scale, pull brush into holder until end of brush
protrudes .08" (2.0 mm) from holder. See Fig. 9
. Note reading on spring scale. Replace spring if tension
is not 5.6-15.5 ozs. (160-440 g).

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 11 © 2005 Mitchell Repair Information Company, LLC.

Fig. 9: Measuring Installed Depth of Brush
Courtesy of MAZDA MOTORS CORP.
Fig. 10: Exploded View of Alternators

Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 12 © 2005 Mitchell Repair Information Company, LLC.

Fig. 11: Exploded View of Alternators
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ALTERNATOR & REGULATOR 1990-92 ELECTRICAL Alternators & Regulators - Mitsubishi
Microsoft
Sunday, July 05, 2009 2:14:54 PMPage 13 © 2005 Mitchell Repair Information Company, LLC.

ELECTRICAL COMPONENT LOCATOR
1991 MAZDA ELECTRICAL COMPONENTS
BUZZERS, RELAYS & TIMERS
BUZZERS, RELAYS & TIMERS LOCATION
CIRCUIT PROTECTION DEVICES
CIRCUIT PROTECTION DEVICES LOCATION
CONTROL UNITS
ComponentLocation
ABS System
Check Valve RelayOn top of ABS pump motor.
Motor RelayOn top of ABS pump motor.
Buzzer & Timer UnitOn bracket, behind left side of dash.
See Fig. 1
.
Circuit Opening RelayOn bracket, behind left side of dash.
See Fig. 1
.
Cooling Fan RelayIn engine compartment fuse/relay
block. See Fig. 1
.
Dashboard Illumination Lights RelayOn bracket, near master cylinder. See
Fig. 1
.
EFI Main RelayIn engine compartment fuse/relay
block. See Fig. 1
& Fig. 2 .
Fuel Pump RelayBehind left front kick panel.
Headlight RelayOn bracket, near master cylinder. See
Fig. 1
.
Headlight Retractor RelayOn bracket, near master cylinder. See
Fig. 1
.
Horn RelayOn bracket, behind left side of dash.
See Fig. 1
.
Ignition RelayIn engine compartment fuse/relay
block.
Turn Signal/Hazard Flasher RelayOn bracket, behind left side of dash.
See Fig. 1
.
ComponentLocation
Fuse BlockBehind left side of dash.
Fuse/Relay BlockIn right rear corner of engine compartment, near firewall.
See Fig. 2
.
Heater Blower Motor Circuit BreakerIn passenger compartment fuse block.

1991 Mazda MX-5 Miata
ELECTRICAL COMPONENT LOCATOR 1991 MAZDA ELECTRICAL COMPONENTS

1991 Mazda MX-5 Miata
ELECTRICAL COMPONENT LOCATOR 1991 MAZDA ELECTRICAL COMPONENTS
Microsoft
Sunday, July 05, 2009 2:15:23 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 2:15:28 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.