1991 MAZDA MIATA jump start

Fig. 7: Locating JC-02 Connector
Courtesy of MAZDA MOTORS CORP.
ANTI-LOCK WARNING LIGHT
Operational Test (Miata)
1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove instrument cluster. Connect 12 volts to terminal 2k of instrument cluster.
See Fig. 8
. Using a jumper wire, connect terminal 1K of instrument cluster to ground. ANTI-LOCK light
should illuminate. If light does not illuminate, check bulb. If bulb is okay, check meter fuse and wiring
harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit and between ANTI-LOCK
light and hydraulic unit. Check operation of hydraulic unit valve relay.
Operational Test (RX7)

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 8 © 2005 Mitchell Repair Information Company, LLC.

1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove clock and bezel assembly from dashboard. Slide warning and clock unit
from instrument panel. Connect terminal "E" to ground. See Fig. 9
. ANTI-LOCK light should illuminate.
If light does not illuminate, check bulb. If bulb is okay, check meter fuse and wiring harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit, and ANTI-LOCK light and
hydraulic unit. Check operation of hydraulic unit valve relay.
Operational Test (929)
1. Start engine, and observe ANTI-LOCK light. Light should illuminate for a few seconds. If light does not
illuminate as described, remove instrument cluster. Connect 12 volts to terminal "J" of instrument cluster
connector I-06. See Fig. 10
. Using a jumper wire, connect terminal "E" of instrument cluster connector I-
08 to negative ground. ANTI-LOCK light should illuminate. If light does not illuminate, check bulb. If
bulb is okay, check meter fuse and wiring harness.
2. Install instrument cluster, and recheck warning light operation. If light still does not illuminate for a few
seconds, check wiring harness between ANTI-LOCK light and control unit and between ANTI-LOCK
light and hydraulic unit. Check operation of hydraulic unit valve relay.
Fig. 8: Testing ANTI
-LOCK Warning Light (Miata)
Courtesy of MAZDA MOTORS CORP.

1991 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1988-91 BRAKES Mazda Anti-Lock Brake System
Microsoft
Sunday, July 05, 2009 2:17:31 PMPage 9 © 2005 Mitchell Repair Information Company, LLC.

continuity does not exist, adjust or replace switch.
BENCH TESTS (ASSEMBLED)
NO-LOAD TEST
Connect fully-charged 12-volt battery, voltmeter and ammeter to starter. See Fig. 2
. Using remote starter wires
or jumper, engage solenoid. Starter should spin smoothly. Note/record meter readings and check no-load
specification. See NO-LOAD TEST SPECIFICATIONS table. If not within specification, disassemble and
inspect starter components.
NO-LOAD TEST SPECIFICATIONS
ApplicationSpecification
B2200 (M/T), Miata, Protege (M/T) & 323
Voltage11.5 Volts
Current60 Amps Maximum
Shaft Speed6500 RPM

1991 Mazda MX-5 Miata
STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive
Microsoft
Sunday, July 05, 2009 2:13:20 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.