1991 LEXUS SC400 engine oil pan

TORQUE SPECIFICATION
AT07F±04\
 \
Part tightened NVm kgf Vcm ft Vlbf\
 
\

\
Engine x Transmission
 

64
 

650
 

47
\
 \
Rear mounting x Body 25 260 19
\
 \
Rear mounting x Extension housing 25 250 18
\
 \
Transmission housing x Transmission case 14 mm (0.55 in.) 34 345 25
\
 \
17 mm (0.67 in.) 57 580 42
\
 \
Extension housing x Transmission case 34 345 25
\
 \
Valve body x Transmission case 10 100 7
\
 \
Oil strainer 10 100 7
\
 \
Oil pan 7.4 75 65 in.
Vlbf\
 \
No.1 vehicle speed sensor 16 160 12\
 
\

\
No.2 vehicle speed sensor 

5.4 

55 

48 in.
Vlbf
\
 \
Solenoid wiring stopper plate 5.4 55 48 in. Vlbf
\
 \
O/D direct clutch speed sensor 5.4 55 48 in. Vlbf
\
 \
Transmission output flange 123 1,250 90
\
 \
Throttle cable x Transmission case 5.4 55 48 in. Vlbf
\
 \
Union 29 300 22
\
 \
Cooler pipe union nut 34 350 25
\
 \
Drive plate x Crankshaft 99 1,000 72
\
 \
Torque converter clutch x Drive plate 33 340 25\
 \
Park/Neutral position switch Bolt 13 130 9\
 \
Nut 6.9 70 61 in. Vlbf\
 
\

\
Control shaft lever
 

16
 

160
 

12
±
A340E (1UZ±FE) AUTOMATIC TRANSMISSION SERVICE SPECIFICATIONSAT±123
WhereEverybodyKnowsYourName

Parts NameFunction
Coolant Level
Warning SwitchThis switch is installed in the radiator reservoir tank. It lights up a \
warning light when the
coolant level becomes low.
Engine Oil Level
Warning SwitchThis switch is mounted in the engine oil pan. It lights a warning light \
when the engine oil
level is low.
Brake Fluid Level
Warning SwitchThis switch is mounted in the brake master cylinder reservoir tank. It l\
ights up a warning
light when the brake fluid level is low.
Parking Brake SwitchThis switch is on the parking brake lever bracket. Continuity in this sw\
itch is established
when the lever is released, causing a warning light to light up.
Door Courtesy SwitchContinuity is established in this switch when a door is opened, causing \
a warning light to
light up.
Warning LightsWhen an abnormality is detected in the vehicle, current is sent to these\
lights, or they are
grounded, causing them to light up.
Indicator LightsCurrent is sent to these lights, or they are grounded, causing them to l\
ight up and indicate
the vehicle's condition to the driver.
Window Washer Level
Warning SwitchThis switch is mounted in the window washer tank. It lights a warning li\
ght when the
window washer level becomes low.
±
BODY ELECTRICAL SYSTEM Cominbation MeterBE±97
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
 Illustration Part No. Part Name Note
 


 

09278±54012
 

Drive Shaft Holding Tool
 


Hydraulic pump pulley
 




 



09286±46011
 




Injection Pump
Spline Shaft Puller
 




Hydraulic pump pulley
 




 



09620±30010
 




Steering Gear Box
Replacer Set
 




 




 



(09627±30010)
 




Steering Sector Shaft
Bushing Replacer
 




Oil seal for hydraulic motor
 




 




(09631±00020)
 




(Handle)
 




Oil seal for hydraulic motor
 




 




09631±10030
 




Oil Seal Remover
 




Oil seal for hydraulic pump
 




 




09843±18020
 




Diagnosis Check
Wire 




RECOMMENDED TOOLS 

Illustration
 

Part No.
 

Part Name
 

Note
 




 




09025±00010
 




Small Torque
Wrench 




For measuring preload
 


 

09082±00015 


TOYOTA
Electrical tester 


 




 



09200±00010
 




Engine Adjust
Kit
 




 




 



09258±00030
 



Hose Plug Set
 




Plug for the vacuum hose, oil hose ect.
 




 




09904±00010
 




Expander
Set
 




Oil seal for hydraulic pump
 




 




09905±00013
 




Snap Ring
Pliers
 




Oil seal for hydraulic pump
CO±4±
COOLIING SYSTEM Preparation
WhereEverybodyKnowsYourName

 
Front water bypass joint x Cylinder head  18 185 13
 Intake manifold x Cylinder head1818513
Delivery pipe x Intake manifold1818513 
Fuel return pipe x Fuel pressure regulator
  
35
 
360
 
26 Fuel inlet hose x Delivery pipe  39 400 29  for SST 33 340 24 Cold start injector x Air intake chamber  7.8 80 69 in.Vlbf Air intake chamber x Intake manifold  18 185 13 EGR pipe x Air intake chamber  18 185 13
 EGR pipe x RH cylinder head  18 185 13
 Cold start injector tube x Air intake chamber  15 150 11
 Union (for brake booster) x Air intake chamber  29 300 22
 Throttle body x Air intake chamber  18 185 13
 IAC valve x Air intake chamber  18 185 13
 EGR valve adaptor x Air intake chamber  18 185 13
 EGR valve x EGR valve adaptor  18 185 13
Timing belt rear plate x Cylinder head7.88069 in. Vlbf 
Water outlet housing x Water pump
  
18
 
185
 
13 Main bearing stud bolt x Cylinder block  15 150 11 Main bearing cap x Cylinder block for nut (1st) 27 275 20  (2nd) Turn 90 5  
  for bolt 49 500 36 Connecting rod cap x Connecting rod 1st 25 250 18
  2nd Turn 905  
 Rear oil seal retainer x Cylinder block  7.8 80 69 in.Vlbf
 Water seal plate x Cylinder block  14 145 10
 Generator bracket x Cylinder block  18 185 13
 Oil pump x Cylinder block 12 mm head 16 160 12
  14 mm head 30 310 22
 No.1 oil pan x Cylinder block 10 mm head 7.8 80 69 in. Vlbf
12 mm head1818513 
No.1 oil pan x Oil pump
  
7.8
 
80
 
69 in. Vlbf No.1 oil pan x Rear oil seal retainer  7.8 80 69 in. Vlbf Oil strainer x Cylinder block  7.8 80 69 in. Vlbf Oil strainer x Oil pump  7.8 80 69 in. Vlbf Oil pan baffle plate x No.1 oil pan  7.8 80 69 in. Vlbf No.1 oil pan x No.2 oil pan  7.8 80 69 in. Vlbf
 Water pump x Cylinder block  18 185 13
 Water bypass pipe x Cylinder Block  18 185 13
 Knock sensor x Cylinder block  44 450 33
 Starter x Cylinder block  39 400 29
 Engine mounting bracket x Cylinder block  37 380 27
 Drive plate x Crankshaft  98 1,000 72
 Transmission x Cylinder block  57 580 42
 Transmission x No.1 oil pan  39 400 29
Drive plate x Torque converter3334025 Transmission oil cooler pipe x Transmission for union nut 34 350 25 Rear engine mounting member x Body  25 250 19\
 \
Rear engine mounting member x Rear engine mounting insulator1313510
EG±210±
1UZ ± FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

The 1 UZ±FE engine has 8±cylinders in a V±arrangement at a bank an\
gle of 905. From the front of the RH
bank cylinders are numbered 2 ± 4 ± 6 ± 8, and from the front of t\
he LH bank cylinders are 1 ± 3 ± 5 ± 7.
The crankshaft is supported by 5 bearings inside the crankcase. These beari\
ngs are made of a copper and
lead alloy.
The crankshaft is integrated with 8 weights for balance. Oil holes are plac\
ed in the center of the crankshaft
to supply oil to the connecting rods, bearing, pistons and other component\
s.
The ignition order is 1 ± 8 ± 4 ± 3 ± 6 ± 5 ± 7 ± 2. T\
he cylinder head is made of alminum alloy, with a cross
flow type intake and exhaust layout and with pent±roof type combustion chambers. The spark plugs are
located in the center of the combustion chambers.
At the front and rear of the intake manifold, a water passage has been p\
rovided which connects the RH
and LH cylinder heads.
Exhaust and intake valves are equipped with irregular pitch springs made\
of special valve spring carbon
steel which are capable of functioning at all engine speeds.
The RH and LH intake camshaft are driven by a timing belt, and a gear on\
the intake camshaft engages
with a gear on the exhaust camshaft to drive it. The cam journal is supp\
orted at 5 (intake) or 4 (exhaust)
places between the valve lifters of each cylinder and on the front end o\
f the cylinder head. Lubrication of
the cam journals and gears is accomplished by oil being supplied through th\
e oiler port in the center of the
camshaft.
Adjustment of the valve clearance is done by means of an outer shim type\
system, in which valve adjusting
shims are located above the valve lifters. This permits replacement of the sh\
ims without removal of the
camshafts.
Pistons are made of high temperature±resistant aluminum alloy, and a depression is built into the piston
head to prevent interference with the valves.
Piston pins are the full±floating type, with the pins fastened to neither the piston boss nor the connecting
rods. Instead, snap rings are fitted on both ends of the pins, preventing the\
pins from falling out.
The No.1 compression ring is made of steel and the No.2 compression ring\
is made of cast iron. The oil
ring is made of a combination of steel and stainless steel. The outer diamet\
er of each piston ring is slightly
larger than the diameter of the piston and the flexibility of the rings allows them to hug the cylinder walls
when they are mounted on the piston. Compression rings No.1 and No.2 work to\
prevent gas leakage from
the cylinder and the oil ring works to scrape oil off the cylinder walls to prevent it from entering the combus-
tion chambers.
The cylinder block is made of aluminum alloy with a bank of 90 5. Cast iron cylinders are installed inside
the cylinder block. It has 8 cylinders which are approximately twice the le\
ngth of the piston stroke. The top
of each cylinder is closed off by the cylinder head and the lower end of the cylinders becomes the crank-
case, in which the crankshaft is installed. In addition, the cylinder block c\
ontains a water jacket, through
which coolant is pumped to cool the cylinders.
The No.1 and No.2 oil pans are bolted onto the bottom of the cylinder bl\
ock. The No.1 oil pan is made of
aluminum alloy. The No.2 oil pan is an oil reservoir made of pressed steel sheet. An o\
il level sensor is
installed in the No.1 oil pan (If oil level drops below a set level, a warning light\
s up.). And oil pan baffle plate
keeps sufficient oil in the bottom of the No.2 oil pan even when the vehicle is t\
ilted. This dividing plate also
prevents the oil from marking waves when the vehicle is stopped suddenly\
and the oil shifts away from the
oil pump suction pipe.
Plastic region tighten bolts are used for the cylinder head, main bearin\
g cap and connecting rod.
EG±4
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

wUsing compressed air and a magnetic finger, remove
the adjusting shim by blowing air into the shim hole.
HINT: Remove the adjusting shim from the intake manifold
side.
NOTICE: Do not drop the adjusting shim into portions A and
B. If dropped into portion A, the adjusting shim will pass
through the cylinder head and cylinder block into the oil pan.
If dropped into portion B, the adjusting shim cannot be recov-
ered without removing the exhaust camshaft.
EG±22±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

30. REMOVE OIL DIPSTICK AND GUIDE FORTRANSMISSION
(a) Remove the bolt holding the oil dipstick to the LH cylinder head.
(b) Pull out the dipstick guide together with the dipstick from the oil pan.
(c) Remove the O±ring from the dipstick guide.
31. REMOVE OIL DIPSTICK AND GUIDE FOR ENGINE
32. REMOVE EGR PIPE
(a) Remove the 2 bolts holding the EGR pipe to the RH exhaust pipe.
(b) Remove the EGR pipe and gasket.
33. DISCONNECT ENGINE WIRE FROM CYLINDER HEADS
(a) Remove the 2 bolts, and disconnect the engine wire protector
from the RH cylinder head.
(b) Remove the bolt, and disconnect the ground strap from the RH cylinder head.
(c) Remove the 5 bolts, and disconnect the engine wire protector
from the LH cylinder head.
34. REMOVE ENGINE HANGERS Remove the 2 bolts and engine hanger. Remove the 2 engine
hangers.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±85
WhereEverybodyKnowsYourName

40. DISCONNECT MAIN HEATED OXYGEN SENSORCONNECTORS
Disconnect the RH and LH oxygen sensor connectors.
41. REMOVE CYLINDER HEADS
(a) Uniformly loosen the ten cylinder head bolts one side of each
cylinder head in several passes, in the sequence shown,
then do the other side as shown. Remove the 20 cylinder
head bolts and plate washers.
NOTICE:
w Cylinder head warpage or cracking could result from
removing bolts in incorrect order.
w Do not drop the plate washer for cylinder head bolt into
portion A of the cylinder head. If dropped into portion A,
the plate washer will pass through the cylinder head and
cylinder block into the oil pan.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±91
WhereEverybodyKnowsYourName