1991 LEXUS SC400 audio

(Woofer)
REMOVAL AND INSTALLATION OF
WOOFER
1. REMOVE WOOFER(a) Remove woofer cover together with high mount stoplight.
(b) Remove four bolts.
(c) Disconnect connector and remove woofer.
2. INSTALL WOOFER For installation follow the removal procedure in reverse.
(Woofer Amplifier)
REMOVAL AND INSTALLATION OF
WOOFER AMPLIFIER
(without CD player)
1. REMOVE WOOFER AMPLIFIER(a) Remove the RH side cover.
(b) Disconnect the connector and remove three nuts and
the woofer amplifier with the bracket.
(c) Remove four bolts and the woofer amplifier.
2. INSTALL WOOFER AMPLIFIER
For installation, follow the removal procedure in reverse.
(with CD player±Pioneer)
1. REMOVE WOOFER AMPLIFIER (a) Remove the package tray trim.
HINT: (See page BO±124)
(b) Remove four bolts.
±
BODY ELECTRICAL SYSTEM Audio SystemBE±209
WhereEverybodyKnowsYourName

(c) Disconnect the connector and remove the wooferamplifier.
2. INSTALL WOOFER AMPLIFIER For installation, follow the removal procedure in reverse.
INSPECTION OF WOOFER AMPLIFIER
INSPECT WOOFER AMPLIFIER
(Circuit)
Disconnect the connector from woofer amplifier and inspect
the connector on the wire harness side as shown.
Check forTester connectionConditionSpecified value
Continuity7±GroundConstantContinuity
Voltage3±GroundConstantBattery voltage
4±GroundIgnition switch positionACC or ONBattery voltage
6±Ground
g
LOCKNo voltage
If circuit is not as specified, refer to BE±201 wiring diagrams
and inspect the circuits connected to other parts.
(Power Amplifier)
REMOVAL AND INSTALLATION OF
POWER AMPLIFIER
(Pioneer)
1. REMOVE POWER AMPLIFIER (a) Remove the RH side cover.
(b) Remove the CD auto changer (See page BE±212).
(c) Disconnect two connectors and remove three nuts and the power amplifier with the bracket.
(d) Remove four bolts and the power amplifier.
2. INSTALL POWER AMPLIFIER For installation, follow the removal procedure in reverse.
BE±210
±
BODY ELECTRICAL SYSTEM Audio System
WhereEverybodyKnowsYourName

(Nakamichi)
1. REMOVE POWER AMPLIFIER
(a) Remove the RH side cover.
(b) Remove the CD auto changer (See page BE±212).
(c) Disconnect three connectors and remove three nuts and the power amplifier with the bracket.
(d) Remove four bolts and the power amplifier.
2. INSTALL WOOFER AMPLIFIER For installation follow the removal procedure in reverse.
POWER AMPLIFIER INSPECTION
INSPECT POWER AMPLIFIER
(Circuit)
Disconnect the connector from power amplifier and inspect
the connector on the wire harness side as shown.
(Produced by PIONEER)
 Check for Tester connection Condition Specified value
 Continuity B7±Ground Constant Continuity
 Voltage B10±Ground Constant Battery positive voltage
  A14±Ground
A6 G d
 Ignition switch position ACC or ON Battery positive voltage  A6±Ground  LOCK No voltage
If circuit is not as specified, refer to BE±201 wiring diagrams
and inspect the circuits connected to other parts.
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±211
WhereEverybodyKnowsYourName

(Produced by NAKAMICHI)
 Check for Tester connection Condition Specified value 

Continuity 

B7±Ground
C7±Ground 


Constant


Continuity
 

Voltage 

B10±Ground
C3±Ground 


Constant


Battery positive voltage
 


 

A6±Ground
A14±Ground 


Ignition switchposition
 


ACC or ON

Battery positive voltage
 


 


C4±Ground
C6±Ground 


Ignition switch position 


LOCK

No voltage
If circuit is not as specified, refer to
BE±203 wiring diagrams
and inspect the circuits connected to other parts.
CD AUTO CHANGER
CD AUTO CHANGER REMOVAL AND
INSTALLATION
1. REMOVE CD AUTO CHANGER (a) Remove RH side cover.
(b) Disconnect two connectors.
(c) Remove three bolts, one nut and the CD auto changer.
CD AUTO CHANGER INSPECTION
INSPECT CD AUTO CHANGER(Circuit)
Disconnect connectors from CD auto changer and inspect
the connector on the wire harness side as shown.
BE±212
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEM
WhereEverybodyKnowsYourName

 
Check for Tester connection Condition Specified value
 Voltage A4±Ground Constant Battery positive voltage
  
A3±Ground
 Ignition switch
iti
 ACC or ON Battery positive voltage
  A3±Ground position LOCK No voltage
 Continuity 
A7±Ground
 Luggage compartment
d t it h
 Push (OFF) No continuity  A7±Ground door courtesy switch Free (ON) Continuity
If circuit is not as specified, refer to BE±201, 203 wiring dia-
grams and inspect the circuits connected to other parts.
HINT:
w Check the wire harness between the radio receiver
assembly and the CD auto changer in accordance with
the wiring diagrams in BE±201, 203.
w Since the signals to and from the CDL+, CDL, CDR+,
CDR, TXM+, TXM, TXS+ and TXS terminals are serial
signals, they cannot ordinarily be measured with a
tester.
LUGGAGE COMPARTMENT DOOR
COURTESY SWITCH
(See page BE±82)
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±213
WhereEverybodyKnowsYourName

MOTOR ANTENNA
MOTOR ANTENNA REMOVAL AND
INSTALLATION
1. REMOVE MOTOR ANTENNA
(a) Remove the antenna nut.
(b) Remove the LH side cover.
(c) Disconnect the motor antenna connector and the antennacord.
(d) Remove the nut and the motor antenna assembly.
2. INSTALL MOTOR ANTENNA
(a) Install the antenna nut.
(b) Connect the motor antenna connector and the antenna cord.
(c) Install the nut.
ANTENNA ROD REMOVAL AND
INSTALLATION
1. REMOVE ANTENNA ROD HINT: Perform this operation with the battery negative (±)
cable connected to the battery terminal.
(a) Turn the ignition switch to ºLOCKº position.
(b) Remove the antenna nut.
(c±1) with CD player
Press the ºAMº and ºCDº buttons on the radio receiver, and
simultaneously turn the ignition switch to ºACCº position.
(c±2) without CD player Press the ºAMº and ºT APEº buttons on the radio receiver, and
simultaneously turn the ignition switch to ºACCº position.
HINT:
w The rod will extend fully and be released from the motor
antenna.
w After removing the antenna rod, leave the ignition switch
at ºACCº.
NOTICE: To prevent body damage when the antenna rod is re-
leased, hold the rod while it comes out.
BE±214±
BODY ELECTRICAL SYSTEM AUDIO SYSTEM
WhereEverybodyKnowsYourName

2. INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.HINT:
wWhen inserting the cable, the teeth on the cable must
face toward the rear of the vehicle.
w Insert the cable approx. 400 mm (15.75 in.).
(b) Wind the cable to retract the rod by turning the ignition switch
to ºLOCKº position.
HINT:
w If the ignition switch is already in ºLOCKº position,
perform step 1.
w In case the cable is not wound, twist it as shown in the
illustration.
w Even if the rod has not retracted fully, install the ant enna
nut and inspect the antenna rod operation. It will finally
retract fully.
(c) Inspect the antenna rod operation by pushing the radio wave
band select buttons.
MOTOR ANTENNA INSPECTION
1. INSPECT MOTOR ANTENNA (Circuit)
Disconnect the motor antenna connector from the body wire
harness and inspect the connector on body wire harness side
as shown.
 Check for Tester connection\
\
Condition Specified value
 Continuity 7±Ground\
\
Constant Continuity
 Voltage 3±Ground\
\
Constant Battery positive voltage
 
g
 8±Ground Ignition switch ACC or ON Battery positive voltage
  8±Ground 
g
position LOCK No voltage
  6±Ground Ignition switch ON Battery positive voltage
  6±Ground 
g
position ACC or LOCK No voltage
  2±Ground Ignition switch Radio or Tape or CD switch ON Battery positive voltage
  2±Ground 
g
ACC or ON Radio or Tape or CD switch OFF No voltage
  5±Ground Ignition switch Radio switch ON Battery positive voltage
  5±Ground 
g
ACC or ON Radio switch OFF No voltage
  
4±Ground
 Ignition switch
ACC or ON and
 AM or FM (87.9 ± 96.0 MHz) Battery positive voltage
  4±Ground ACC or ON and
radio switch ON Others No voltage
 


 

1±Ground
 

Ignition switch
ACC or ON and 

AM
 

Battery positive voltage
   radio switch ON Others No voltage
If circuit is not as specified, inspect radio or wire harness. If
circuit is as specified, replace motor antenna.
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEMBE±215
WhereEverybodyKnowsYourName

2. INSPECT ANTENNA MOTOR
(a) Install antenna nut.
(b) Disconnect connector from the motor antenna control relay.
(c) Connect the positive (+) lead from the battery to terminal 2and the negative (±) lead to terminal 5 on the wire harness
side connector.
(d) Check that the motor turns (moves upward).
NOTICE: These tests must be performed quickly (within 4±8
seconds) to prevent the coil from burning out.
(e) Then, reverse the polarity, check that the motor turns the opposite way (moves downward).
NOTICE: These tests must be performed quickly (within 4±8
seconds) to prevent the coil from burning out.
HINT: When the motor is normal, lower the antenna to the
lower most position.
If operation is not as specified, replace the antenna motor as-
sembly.
GLASS PRINTED ANTENNA
GLASS PRINTED ANTENNA
INSPECTION
1. INSPECT GLASS PRINTED ANTENNA(Use same procedure as for ºINSPECT DEFOGGER
WIRESº on page BE±173.)
2. REPAIR GLASS PRINTED ANTENNA (Use same procedure as for ºREPAIR DEFOGGER WIRESº
on page BE±174.)
BE±216
±
BODY ELECTRICAL SYSTEM AUDIO SYSTEM
WhereEverybodyKnowsYourName