1991 LEXUS SC400 turn signal

167
4. AUTO RETURN OPERATION
WHEN THE STEERING IS IN ªAUTO AWAYº CONDITION AND THE IGNITION KEY IS INSERTED INTO THE IGNITION KEY CYLINDER
(UNLOCK WARNING SW ON), A SIGNAL IS INPUT TO TERMINAL UWSW OF TILT AND POWER TELESCOPIC ECU.
AS A RESULT, THE TILT AND POWER TELESCOPIC ECU OPERATES AND THE CURRENT TO TERMINAL +B OF TILT AND POWER
TELESCOPIC ECU FLOWS FROM TERMINAL TEM± OF TILT AND POWER TELESCOPIC ECU "TERMINAL 4 OF COMB. SW "
TERMINAL 1 OF TELESCOPIC CONTROL MOTOR "TERMINAL 2 " TERMINAL 1 OF COMB. SW " TERMINAL TEM+ OF TILT AND
POWER TELESCOPIC ECU " TERMINAL GND2 "GROUND , AND AT THE SAME TIME, CURRENT FLOWS FROM TERMINAL TIM± OF
TILT AND POWER TELESCOPIC ECU "TERMINAL 10 OF COMB. SW "TERMINAL 1 OF TILT CONTROL MOTOR "TERMINAL 2 "
TERMINAL 1 OF COMB. SW "TERMINAL TIM+ OF TILT AND POWER TELESCOPIC ECU "TERMINAL GND2 "GROUND , CAUSING
BOTH THE TILT CONTROL MOTOR AND TELESCOPIC CONTROL MOTOR TO ROTATE. THE MOTORS CONTINUE TO ROTATE UNTIL
THE SIGNALS INPUT FROM THE TILT POSITION SENSOR TO TERMINAL TIS OF TILT AND POWER TELESCOPIC ECU AND FROM THE
TELESCOPIC POSITION SENSOR TERMINAL TES OF TILT AND POWER TELESCOPIC ECU (SIGNALS INFORMING THE ECU OF THE
CURRENT POSITION OF THE STEERING) MATCH THE POSITION MEMORIZED BY THE ECU PRIOR TO AUTO AWAY OPERATION.
IN THIS WAY, THE STEERING POSITION IS AUTOMATICALLY RETURNED TO THE ORIGINAL POSITION.
WHEN THE IGNITION SW IS TURNED FROM OFF TO ON OR THE SHIFT LEVER IS SHIFTED TO A POSITION OTHER THAN P OR N,
AUTO OPERATION IS STOPPED.
C15 TILT AND POWER TELESCOPIC UNIT [COMB. SW]
4±6 : APPROX. 160
WITH TELESCOPIC LONG OPERATION
: APPROX. 360
WITH TILT UP OPERATION
: APPROX. 790
WITH TELESCOPIC SHORT OPERATION
: APPROX. 2.0K
WITH TILT DOWN OPERATION
8±7 : CONTINUITY WITH AUTO SW OFF
8±4 : APPROX. 5K

T 7 (D) TELESCOPIC POSITION SENSOR
6±3 : APPROX. 5K

D10 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH
3±6GROUND :CLOSED WITH FRONT DOOR LH OPEN
D12 DRIVING POSITION MEMORY AND RETURN SW
2±3 : CLOSED WITH DRIVING POSITION MEMORY SW (NO. 1) ON
1±3 : CLOSED WITH DRIVING POSITION MEMORY SW (NO. 2) ON
4±3 : CLOSED WITH DRIVING POSITION MEMORY SW (SET) ON
I15 UNLOCK WARNING SW [IGNITION SW]
9±10: CLOSED WITH IGNITION KEY IN CYLINDER
N 1 A/T INDICATOR SW [NEUTRAL START SW]
9±1 : CLOSED WITH SHIFT LEVER AT P POSITION
T10, T11 TILT AND POWER TELESCOPIC ECU
(A) 4±GROUND : ALWAYS APPROX. 12 VOLTS
(A) 1±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
(B) 18±GROUND : ALWAYS APPROX. 12 VOLTS
(A) 6±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON AND SHIFT LEVER AT ªPº RANGE
(B) 10±GROUND : CONTINUITY WITH IGNITION KEY IN CYLINDER
(A) 7±GROUND : ALWAYS CONTINUITY
(B) 8±GROUND : ALWAYS CONTINUITY
(B) 2±GROUND : CONTINUITY WITH FRONT DOOR LH OPEN
(B) 3±GROUND : CONTINUITY WITH DRIVING POSITION MEMORY SW (NO. 1) ON
(B) 12±GROUND : CONTINUITY WITH DRIVING POSITION MEMORY SW (NO. 2) ON
(B) 11±GROUND : CONTINUITY WITH DRIVING POSITION MEMORY SW (SET) ON
(A) 10±GROUND : APPROX. 12 VOLTS WITH TILT UP OPERATION
(A) 3±GROUND : APPROX. 12 VOLTS WITH TILT DOWN OPERATION
(A) 2±GROUND : APPROX. 12 VOLTS WITH TELESCOPIC SHORT OPERATION
(A) 11±GROUND : APPROX. 12 VOLTS WITH TELESCOPIC LONG OPERATION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1728N 127T 732
D1030P 329T10B29
D1230P1127T11A29
I1529R 732
SERVICE HINTS
WhereEverybodyKnowsYourName

172
REMOTE CONTROL MIRROR (w/ DRIVING POSITION MEMORY)
CURRENT IS ALWAYS APPLIED TO TERMINAL +B OF REMOTE CONTROL MIRROR ECU THROUGH THE ECU±B FUSE.
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE CURRENT FLOWS TO TERMINAL ACC OF THE REMOTE
CONTROL MIRROR ECU THROUGH THE RADIO NO. 2 FUSE.
REMOTE CONTROL MIRROR OPERATION
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE REMOTE CONTROL MIRROR ECU OPERATES. WHEN THE
SELECT SW OF THE REMOTE CONTROL MIRROR SW IS MOVED TO THE LH POSITION AND THE OPERATION SW IS MOVED TO
ªLEFTº SIDE, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU TO TERMINAL 2 OF REMOTE
CONTROL MIRROR SW " TERMINAL 12 "TERMINAL SWI2 OF ECU.
AS A RESULT, THE CURRENT TO TERMINAL +B OF ECU FLOWS FROM TERMINAL MHL OF ECU "TERMINAL 1 OF REMOTE
CONTROL MIRROR LH " MOTOR " TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND , ROTATING THE MOTOR
TO ADJUST THE ANGLE OF THE LEFT SIDE OF THE OUTER MIRROR (DRIVER'S).
TO CHANGE THE ANGLE OF THE RIGHT SIDE OF THE MIRROR, THE OPERATION SW OF THE REMOTE CONTROL MIRROR SW IS
MOVED TO THE ªRIGHTº SIDE.
THEN, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU " TERMINAL 2 OF REMOTE CONTROL
MIRROR SW " TERMINAL 8 "TERMINAL SWI1 OF ECU. AS A RESULT, THE CURRENT TO TERMINAL +B OF REMOTE CONTROL
MIRROR ECU FLOWS FROM TERMINAL M+L OF ECU " TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR " TERMINAL 1 "
TERMINAL MHL OF ECU " TERMINAL GND " GROUND, CAUSING THE ANGLE OF THE OUTER MIRROR (DRIVER'S) TO CHANGE ON
THE RIGHT SIDE.
THE MOVEMENT TO OTHER POSITIONS OCCURS SIMILARLY, SO ONLY THE CURRENT FLOW TO EACH MOTOR IS SHOWN:
SELECT SW RH POSITION, OPERATION SW LEFT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL MHR "TERMINAL 1 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW RIGHT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 1 "TERMINAL MHR OF ECU " TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU " TERMINAL MVL " TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+L "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVL OF ECU " TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL MVR "TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVR OF ECU " TERMINAL GND "GROUND .
THE NUMBER OF TURNS OF EACH MOTOR (AMOUNT OF MOVEMENT OF EACH PART OF THE MIRROR) IS DETECTED BY THE
POSITION SENSORS AND INPUT TO THE ECU, MAKING IT POSSIBLE TO PERFORM MEMORY AND RETURN FUNCTIONS FOR THE
MIRROR POSITION USING THE DRIVING POSITION MEMORY AND RETURN SWITCH.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

189
WHEN THE IGNITION SW IS TURNED TO ACC POSITION THE CURRENT FROM THE CIG FUSE FLOWS TO TERMINAL 1 OF THE SHIFT
LOCK ECU, IN THE ON POSITION, THE CURRENT FROM THE ECU±IG FUSE FLOWS TO TERMINAL 5 OF THE ECU.
1. SHIFT LOCK MECHANISM
WITH THE IGNITION SW ON, WHEN A SIGNAL THAT THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) AND A SIGNAL THAT
THE SHIFT LEVER IS PUT IN ªPº RANGE (CONTINUITY BETWEEN P1 AND P OF THE SHIFT LOCK CONTROL SW) IS INPUT TO THE
ECU, THE ECU OPERATES AND CURRENT FLOWS FROM TERMINAL 5 OF THE ECU " TERMINAL SL+ OF THE SHIFT LOCK
SOLENOID " SOLENOID " TERMINAL SL± " TERMINAL 3 OF THE ECU " GROUND. THIS CAUSES THE SHIFT LOCK SOLENOID TO
TURN ON (PLATE STOPPER DISENGAGES) AND THE SHIFT LEVER CAN SHIFT INTO RANGE OTHER THAN THE ªPº RANGE.
2. KEY INTER LOCK MECHANISM
WITH THE IGNITION SW ON OR ACC POSITION, WHEN THE SHIFT LEVER IS PUT IN ªPº RANGE (NO CONTINUIT\
Y BETWEEN P2 AND P
OF SHIFT LOCK CONTROL SW), THE CURRENT FLOWING FROM TERMINAL 2 OF THE ECU " KEY INTER LOCK SOLENOID IS CUT
OFF. THIS CAUSES THE KEY INTER LOCK SOLENOID TO TURN OFF (LOCK LEVER DISENGAGES FROM LOCK POSITION) AND THE
IGNITION KEY CAN BE TURNED FROM ACC TO LOCK POSITION. IF THE IGNITION IS LEFT IN ACC OR ON POSITION WITH THE SHIFT
LEVER IN OTHER THAN ªPº RANGE, THAN AFTER APPROX. ONE HOUR THE ECU\
OPERATES TO RELEASE THE LOCK.
S10 SHIFT LOCK ECU
1±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
5±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : ALWAYS CONTINUITY
4±GROUND : APPROX. 12 VOLTS WITH BRAKE PEDAL DEPRESSED
S12 STOP LIGHT SW
2±1 : CLOSED WITH BRAKE PEDAL DEPRESSED
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
I1529S1029S1229
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A
3G22INSTRUMENT PANEL WIRE
3H
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
X 78 12345
12
I15 S 10 S 12
BLACK
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName

11 5
CURRENT ALWAYS FLOWS TO TERMINAL (A)8 OF THE DOOR LOCK ECU THROUGH THE DOOR FUSE, AND TO TERMINAL (A)20
THROUGH THE DOME FUSE.
WHEN THE IGNITION SW IS TURNED ON, THE CURRENT FLOWING THROUGH THE ECU±IG FUSE " TERMINAL (A)2 OF THE ECU "
TERMINAL (B)8 FLOWS THROUGH THE COIL SIDE OF THE POWER MAIN RELAY TO GROUND, CAUSING THE RELAY TO OPERATE.
THE CURRENT FLOWING THROUGH THE POWER FUSE FLOWS TO THE DOOR LOCK CONTROL SW LH, CAUSING THE INDICATOR
LIGHT TO LIGHT UP.
1. MANUAL LOCK OPERATION
WHEN THE DOOR CONTROL SW OR KEY SW ARE PUSHED TO LOCK POSITION, A LOCK SIGNAL IS INPUT TO TERMINAL (A)17, (A)14
(FOR KEY SW) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION. CURRENT FLOWS FROM TERMINAL (A)8 OF THE
ECU " TERMINAL (A)4 " TERMINAL 5 OF THE DOOR LOCK MOTORS " TERMINAL 2 " TERMINAL (A)3 OF THE ECU " TERMINAL
(A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO LOCK.
2. MANUAL UNLOCK OPERATION
WHEN THE DOOR LOCK CONTROL SW OR KEY ARE PUSHED TO UNLOCK POSITION, AN UNLOCK SIGNAL IS INPUT TO TERMINAL
(A)18, (A)10 (FOR KEY SW LH) OR (A)15 (FOR KEY SW RH) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION.
CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU " TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL
5 " TERMINAL (A)4 OF THE ECU "TERMINAL (A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO
UNLOCK.
WHEN UNLOCK OPERATION OCCURS USING THE LH DOOR KEY SW, PERFORMING THE UNLOCK OPERATION ONCE UNLOCKS
ONLY THE DRIVER'S DOOR. TO UNLOCK ALL THE OTHER DOORS TOGETHER, UNLOCK OPERATION MUST BE PERFORMED AGAIN
WITHIN 3 SECONDS OF THE FIRST OPERATION.
3. IGNITION KEY REMINDER OPERATION
* OPERATION OF DOOR LOCK BUTTON (OPERATION OF DOOR LOCK MOTORS)
WHEN THE IGNITION KEY IS IN THE CYLINDER (UNLOCK WARNING SW ON) AND THE DOOR IS OPENED AND LOCKED USING
DOOR LOCK BUTTON (DOOR LOCK MOTOR), THE DOOR IS LOCKED ONCE BUT EACH DOOR IS UNLOCKED SOON BY THE
OPERATION OF THE ECU. AS A RESULT OF ECU ACTIVATION, THE CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU "
TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL 5 " TERMINAL (A)4 OF THE ECU " TERMINAL (A)16
" TO GROUND AND CAUSES ALL THE DOORS TO UNLOCK.
THE SAME APPLIES TO OPERATION OF THE DOOR LOCK CONTROL SW AND DOOR LOCK KEY SW.
* KEY LESS LOCK OPERATION
WHEN THE IGNITION KEY IS STILL INSERTED IN THE CYLINDER (UNLOCK WARNING SW ON), THE DOOR IS OPEN AND UNLOCK
OPERATION IS PREVENTED BY KEEPING THE DOOR LOCK BUTTON PRESSED TO THE LOCK SIDE, THE DOOR IS KEPT IN THE
LOCK CONDITION. IF THE DOOR IS THEN CLOSED, A SIGNAL IS INPUT TO THE ECU FROM THE DOOR COURTESY SW. THIS
ACTIVATES THE ECU AND EACH DOOR IS UNLOCKED.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

104
TURN SIGNAL AND HAZARD WARNING LIGHT
1E
7 2
1A
71A 41C 41C 31E19 1E14
2 3 2 3 1H
11 1H 7
1J 1 3G
3
3A 1
1E 18
1K 6 3D
10
4
4
4
4
4
IQ2
8
IQ1
10 IQ1
12 IQ1 11
IG2
9IG1 10 IG123
IQ2
13
I7 I7
B15
EB EA BM IF 55
9
756 4123 10 8
66
1
4
2
5
3
A
16 A 17
B
23
IG2
8
IQ2 3
IE19
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
HAZARD TURNRH
LH
OFF
ON 20A
TURN
25A
HAZ±HORN
TURN SIGNAL
FLASHER TURN SIGNAL SW [COMB. SW]
HA ZARD SW
FRONT TURN
SIGNAL LIGHT
REAR TURN SIGNAL LIGHT
[REAR COMB. LIGHT] TURN SIGNAL INDICATOR
LIGHT [COMB. METER]
LH RH RH
LH WW
R±W R±B
R±W
R±W W±R
R±B
G± Y
G± B
W±BW±B
W±B
W±B
G±R
G±R
W
W
W±R
W±B
W±R
R±WR±B
R±B
R±W
R±W
R±B
R±W
W±BR±B
G±Y
G±B
G±Y
G±B
G±Y
G±Y G±B
W±B W±B
W±B W±B W±B W±B
W±B 5
R±B
H7
C16
F7 F8 R10 R11
C13 , C 1 4AB
LH RH
6
WhereEverybodyKnowsYourName

105
TURN SIGNAL FLASHER
(4) 3 ± GROUND: CHANGES FROM APPROX. 12 VOLTS TO 0 VOLTS WITH IGNITION SW ON AND TURN SIGNAL SW LEFT, OR WITH
HAZARD SW ON
(4) 5 ± GROUND: CHANGES FROM APPROX. 12 VOLTS TO 0 VOLTS WITH IGNITION SW ON AND TURN SIGNAL SW RIGHT, OR WITH
HAZARD SW ON
(4) 4 ± GROUND: CONTINUITY WITH TURN SIGNAL SW LEFT, OR HAZARD SW ON
(4) 2 ± GROUND: CONTINUITY WITH TURN SIGNAL SW RIGHT, OR HAZARD SW ON
(4) 1 ± GROUND: APPROX. 12 VOLTS WITH IGNITION SW ON OR HAZARD SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C13A28F 726R1031
C14B28F 826R1131
C1628H 729
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
423LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20ENGINE ROOM MAIN WIRE
1C20FLOOR WIRE
1E20INSTRUMENT PANEL WIRE
1H
1J20COWL WIRE
1K
20COWL WIRE
3A
3D22INSTRUMENT PANEL WIRE
3G
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO. 4)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO 5)IG236INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)IQ238INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PA N E L CENTER)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA34FRONT SIDE OF RIGHT FENDER
EB34FRONT SIDE OF LEFT FENDER
IF36LEFT KICK PANEL
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 738COWL WIREB1540FLOOR MAIN WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

106
TURN SIGNAL AND HAZARD WARNING LIGHT
WhereEverybodyKnowsYourName

185
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 7 OF THE INTEGRATION RELAY.
AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE INTEGRATION RELAY AND, FOR APPROX. 4±8 SECONDS, CURRENT FLOWING
THROUGH THE WARNING LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY " TERMINAL 10 " GROUND, CAUSING THE WARNING
LIGHT TO LIGHT UP. AT THE SAME TIME AS THE WARNING LIGHT LIGHTS UP, A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8
OF THE RELAY, THE CURRENT FLOWING TO TERMINAL 7 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT
BELT WARNING BUZZER SOUNDS FOR APPROX. 4±8 SECONDS. HOWEVER, IF THE SEAT BELT IS PUT ON DURING THIS PERIOD
(WHILE THE BUZZER IS SOUNDING), SIGNAL INPUT TO TERMINAL 8 OF RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 7
OF THE RELAY " TERMINAL 10 " GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK SW ON), THE IGNITION SW STILL OFF AND \
DOOR OPEN (DOOR
COURTESY SW ON), WHEN A SIGNAL IS INPUT TO TERMINAL 6 OF THE RELAY, THE INTEGRATION RELAY OPERATES, CURRENT
FLOWS FROM TERMINAL 7 OF THE RELAY " TERMINAL 10 " GROUND AND UNLOCK WARNING BUZZER SOUNDS.
B 4 BUCKLE SW LH
1±2 : CLOSED WITH DRIVER'S LAP BELT IN USE
D10 DOOR COURTESY SW LH
3±6 : CLOSED WITH LH DOOR OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
10±9: CLOSED WITH IGNITION KEY IN CYLINDER
INTEGRATION RELAY
10±GROUND: ALWAYS CONTINUITY6±GROUND: CONTINUITY WITH DRIVER'S DOOR OPEN
5±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND: CONTINUITY WITH DRIVER'S LAP BELT IN USA
9±GROUND: 0 VOLTS FOR 4±8 SECONDS WITH IGNITION SW ON AND APPROX. 12 VOLTS 4±8 SECONDS AFTER IGNITION SW ON
1±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 432C14B28I1529
C12A28D1030
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1C20FLOOR MAIN
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)Ba242FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
BK40UNDER THE CENTER PILLAR LH
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName