1991 LEXUS SC300 oil pressure

15. REMOVE RH NO.2 TIMING BELT COVER(a) Disconnect the cam position sensor connector from theignition coil bracket.
(b) Disconnect the cam position sensor wire from the clamp
on the timing belt cover.
(c) Remove the five mounting bolts.
(d) Disconnect the wire clamp from the timing belt cover,
and remove the timing belt cover and four gasket.
16. REMOVE LH NO.2 TIMING BELT COVER (a) Disconnect the cam position sensor wire from the clamp
on the timing belt cover.
(b) Disconnect the cam position sensor connector.
(c) Remove the three mounting bolts.
(d) Disconnect the connector grommet from the timing belt cover, and remove the timing belt cover and two
gaskets.
17. DISCONNECT PRESSURE AND SUCTION HOSES FROM HYDRAULIC PUMP
18. REMOVE HYDRAULIC PUMP (a) Disconnect the solenoid valve connector.
(b) Remove the two mounting bolts and two nuts.
(c) Disconnect the engine speed sensor wire clamp.
(d) Remove the hydraulic pump.
CO±30
±
COOLIING SYSTEM Electronically Controlled Hydraulic
Cooling Fan (Hydraulic Pump)
WhereEverybodyKnowsYourName

INSTALLATION OF HYDRAULIC PUMP
(See Components on page CO±26)
1. INSTALL HYDRAULIC PUMP (a) Install the hydraulic pump, solenoid valve connector
clamp and engine speed sensor wire clamp with the two
bolts and two nuts.
Torque:
12 mm head 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
14 mm head 20 N Vm (310 kgf Vcm, 22 ft Vlbf)
HINT: Each bolt length is indicated in the illustration.
Bolt length:
A 106 mm (4.17 in.) for 12 mm head
B 114 mm (4.49 in.) for 14 mm head
(b) Connect the solenoid valve connector.
2. CONNECT PRESSURE AND SUCTION HOSES TO HYDRAULIC PUMP
(a) Connect the pressure hose with new gasket and unionbolt.
Torque: 64 N Vm (650 kgf Vcm, 47 ft Vlbf)
(b) Connect suction hose.
3. INSTALL RH NO.2 TIMING BELT COVER
(a) Install the four gaskets to the timing belt cover.
(b) Install the connector grommet to the timing belt cover.
(c) Install the timing belt cover with the five bolts.
Torque: 16 N Vm (160 kgf Vcm, 12 ft Vlbf)
HINT (12 mm head bolt): Use bolts 106 mm (4.17 in.) in
length.
(d) Install the wire clamp to the timing belt cover.
(e) Install the cam position sensor wire to the wire clamp on
the timing belt cover.
(f) Install the cam position sensor connector to the ignition coil bracket.
4. INSTALL LH NO.2 TIMING BELT COVER (a) Install the two gaskets to the timing belt cover.
(b) Run the cam po sition sensor wire through the timing belt
cover hole.
(c) Install the timing belt cover and connector bracket with the three bolts.
(d) Connect the cam position sensor connector.
(e) In sta ll th e ca m po sitio n se n so r c onnector to the
connector bracket.
(f) Install the cam position sensor wire to the wire clamp on
the timing belt cover.
(g) Install the connector grommet to the timing belt cover.
CO±42
±
COOLIING SYSTEM Electronically Controlled Hydraulic Cooling Fan
(Hydraulic Pump)
WhereEverybodyKnowsYourName

 
Compression at 250 rpm STD 1,226 kPa (12.5 kgf/cm2, 178 psi) or
more
 pressureLimit 981 kPa (10.0 kgf/cm2, 142 psi)  Difference of pressure between each cylinder  98 kPa (1.0 kgf/cm2, 14 psi) or less 

Timing belt
tensionerProtrusion from housing end10.5±11.5 mm (0.413±0.453 in.)
 Cylinder head Warpage Limit 0.10 mm (0.039 in.)
  Valve seat  
  Refacing angle  30
5, 45 5, 75 5
  Contacting angle  455
  Contacting width  1.0±1.4 mm (0.039±0.055 in.)
  Cylinder head bolt thread inside diameter STD 9.770±9.960 mm (0.3846±0.3921 in.)
   Limit 9.60 mm (0.3780 in.)
 Valve guideInside diameter6.010±6.030 mm (0.2366±0.2374 in.)
 bushing Outside diameter (for repair part) STD 11.048±11.059 mm (0.4350±0.4354
in.)
 O/S 0.05 11.098±11.109 mm (0.4369±0.4374 in.) ValveValve overall lengthSTD (Intake)94.95 mm (3.7382 in.)   (Exhaust) 96.90 mm (3.8150 in.)   Limit (Intake) 94.45 mm (3.7185 in.)   (Exhaust) 96.40 mm (3.7953 in.)
  Vale face angle  44.55
  Stem diameter Intake 5.970±5.985 mm (0.2350±0.2356 in.)
   Exhaust 5.965±5.980 mm (0.2348±0.2354 in.)
  Stem oil clearance STD (Intake) 0.025±0.060 mm (0.0010±0.0024 in.)
   (Exhaust) 0.030±0.065 mm (0.0012±0.0026 in.)
   Limit (Intake) 0.08 mm (0.0031 in.)
   (Exhaust) 0.10 mm (0.0039 in.)
  Margin thickness STD 1.0 mm (0.039 in.)
   Limit 0.5 mm (0.020 in.)
 Valve spring Squareness Limit 2.0 mm (0.079 in.)
  Free length  43.6 mm (1.717 in.)
  Installed tension at 32.9 mm (1.295 in.)  186±206 N (19.0±21.0 kgf, 41.9±46.3
lbf)
 

Valve lifter 

Lifter diameter 


 

30.966±30.976 mm (1.2191±2.2195
in.)
 


 


Lifter bore diameter 


 


31.000±31.016 mm (1.2205±1.2211
in.)
  Oil clearance STD 0.024±0.050 mm (0.0009±0.0020 in.)
   Limit 0.07 mm (0.0028 in.)
EG±206±
1UZ ± FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

 
Front water bypass joint x Cylinder head  18 185 13
 Intake manifold x Cylinder head1818513
Delivery pipe x Intake manifold1818513 
Fuel return pipe x Fuel pressure regulator
  
35
 
360
 
26 Fuel inlet hose x Delivery pipe  39 400 29  for SST 33 340 24 Cold start injector x Air intake chamber  7.8 80 69 in.Vlbf Air intake chamber x Intake manifold  18 185 13 EGR pipe x Air intake chamber  18 185 13
 EGR pipe x RH cylinder head  18 185 13
 Cold start injector tube x Air intake chamber  15 150 11
 Union (for brake booster) x Air intake chamber  29 300 22
 Throttle body x Air intake chamber  18 185 13
 IAC valve x Air intake chamber  18 185 13
 EGR valve adaptor x Air intake chamber  18 185 13
 EGR valve x EGR valve adaptor  18 185 13
Timing belt rear plate x Cylinder head7.88069 in. Vlbf 
Water outlet housing x Water pump
  
18
 
185
 
13 Main bearing stud bolt x Cylinder block  15 150 11 Main bearing cap x Cylinder block for nut (1st) 27 275 20  (2nd) Turn 90 5  
  for bolt 49 500 36 Connecting rod cap x Connecting rod 1st 25 250 18
  2nd Turn 905  
 Rear oil seal retainer x Cylinder block  7.8 80 69 in.Vlbf
 Water seal plate x Cylinder block  14 145 10
 Generator bracket x Cylinder block  18 185 13
 Oil pump x Cylinder block 12 mm head 16 160 12
  14 mm head 30 310 22
 No.1 oil pan x Cylinder block 10 mm head 7.8 80 69 in. Vlbf
12 mm head1818513 
No.1 oil pan x Oil pump
  
7.8
 
80
 
69 in. Vlbf No.1 oil pan x Rear oil seal retainer  7.8 80 69 in. Vlbf Oil strainer x Cylinder block  7.8 80 69 in. Vlbf Oil strainer x Oil pump  7.8 80 69 in. Vlbf Oil pan baffle plate x No.1 oil pan  7.8 80 69 in. Vlbf No.1 oil pan x No.2 oil pan  7.8 80 69 in. Vlbf
 Water pump x Cylinder block  18 185 13
 Water bypass pipe x Cylinder Block  18 185 13
 Knock sensor x Cylinder block  44 450 33
 Starter x Cylinder block  39 400 29
 Engine mounting bracket x Cylinder block  37 380 27
 Drive plate x Crankshaft  98 1,000 72
 Transmission x Cylinder block  57 580 42
 Transmission x No.1 oil pan  39 400 29
Drive plate x Torque converter3334025 Transmission oil cooler pipe x Transmission for union nut 34 350 25 Rear engine mounting member x Body  25 250 19\
 \
Rear engine mounting member x Rear engine mounting insulator1313510
EG±210±
1UZ ± FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

TUNE±UP
EG10Z±05
ENGINE COOLANT INSPECTION
1. CHECK ENGINE COOLANT LEVEL AT RESERVOIR TANK
The coolant level should be above the ªCOLD LEVELº at nor-
mal temperature (20 5C (68 5F)).
If low, check for leaks and add coolant up to the ªCOLD LEV-
ELº
2. CHECK ENGINE COOLANT QUALITY
(a) Remove the radiator cap from the reservoir tank.
CAUTION: To avoid the danger of being burned, do not remove
it while the engine and radiator are still hot as fluid and steam
can be blown out under pressure
(b) There should not be any excessive deposits of rust or scale around the radiator cap or reservoir tank filler hole, and the
coolant should be free from oil.
If excessively dirty, clean the coolant passages and replace
the coolant.
Capacity (w/ Heater):
10.8 liters (11.4 US qts, 9.5 lmp. qts)
HINT:
wUse a good brand of ethylene±glycol base coolant and
mix it according to the manufacturer's directions.
w Using coolant which includes more than 50%
ethylene±glycol(but not more than 70%) is
recommended.
NOTICE:
w Do not use a alcohol type coolant.
w The coolant should be mixed with demineralized water or
distilled water.
(c) Reinstall the radiator cap.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±9
WhereEverybodyKnowsYourName

COMPRESSION CHECK
EG21U±02
HINT: If there is lack of power, excessive oil consumption or
poor fuel economy, measure the compression pressure.
1. WARM UP AND STOP ENGINE Allow the engine to warm up to normal operating tempera-
ture.
2. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY
CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the ªLOCKº posi-
tion and the negative (±) terminal cable is disconnected
from the battery.
3. REMOVE INTAKE AIR CONNECTOR
(a) Disconnect the following hoses: (1) Air hose from IAC valve
(2) Air hose (from air control valve on PS pump) from intake
air connector
(b) Remove the bolt holding the intake air connector to the cylinder head cover.
(c) Remove the 2 hose clamps.
(d) Disconnect the intake air connector from the throttle body
and air cleaner hose, and remove the intake air connector.
4. REMOVE UPPER HIGH±TENSION CORD COVER
(a) Remove the 2 bolts.
(b) Disconnect the front side claw groove of the upper cord cover
from the claw of lower cord cover, and remove the upper cord
cover.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±37
WhereEverybodyKnowsYourName

15. CHECK CYLINDER COMPRESSION PRESSURE
(a) Reconnect the battery negative (±) cable.
(b) Insert a compression gauge into the spark plug hole.
(c) Fully open the throttle.
(d) Wh ile cra n kin g th e en g in e , me a su re th e co mp re ssio npressure.
HINT: Always use a fully charged battery to obtain engine
speed of 250 rpm or more.
(e) Repeat steps (b) through (d) for each cylinder. NOTICE: This measurement must be done in as short a
time as possible.
Compression pressure:
1,226 kPa (12.5 kgf/cm
2, 178 psi) or more
Minimum pressure: 981 kPa (10.0 kgf/cm
2, 142 psi)
Difference between each cylinder: 98 kPa (1.0 kgf/cm
2, 14 psi) or less
(f) If the cylinder compression in one or more cylinders is low,pour a sm all amount of engine oil into the cylinder through the
spark plug hole and repeat steps (b) through (d) for cylinders
with low compression.
w If adding oil helps the compression, it is likely that the
piston rings and/or cylinder bore are worn or damage.
w If pressure stays low, a valve may be sticking or seating
is improper, or there may be leakage past the gasket.
(g) Disconnect the battery negative (±) cable.
16. REINSTALL SPARK PLUGS
Using a 16 mm plug wrench, install the 8 spark plugs.
Torque: 18 N Vm (180 kgf Vcm, 13 ft Vlbf)
17. R E C O N N E C T H I G H ± T E N S I O N C O R D S TO S PA R K
PLUGS
18. RECONNECT RH CAMSHAFT POSITION SENSOR CONNECTOR
(a) Connect the camshaft position sensor connector.
(b) Install the camshaft position sensor connector to the ignition
coil bracket.
EG±40
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

(c) Disconnect the following hoses:(1) 2 oil cooler hoses (for cooling fan) from pipes
(2) 2 radiator hoses
(3) 2 oil cooler hoses (for transmission) from radiator
HINT: Plug the hose ends.
(4) Suction hose from hydraulic pump
(5) Pressure hose from hydraulic pump
(d) Remove the 2 bolts, screw and upper radiator support. Remove the 2 upper radiator supports.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±47
WhereEverybodyKnowsYourName