1990 MITSUBISHI ECLIPSE low beam

GENERAL - Technical Featureso-5ENGINE
The engines are the transverse-mounted engine
especially for front-engine/front-wheeldrive orfront-engine/4-wheel drive models, the
2.OL DOHC
16-valve engine with high-performance, silent-
operation,low-vibration,low-noise,low-fuel-
consumption features, an engine that fully displays
the most
up-todate engine technology.
SPECIFICATIONS
Engine model
Displacement
cc (cu.in.1
h$xo$put (SAE net)Max. torque (SAE net)
ft.Ibs./rpm
4G63Non-Turbo1997(122)135/6000125/5000
4663Turbo1997(122)195/6000203/3000
FEATURESHigh performance and low fuel consumption
l The rocker arm reduces the valve-actuation torque as well as fuel consumption.
l Air-intake efficiency improved through the adoption of the optimum air-intake system layout.
l Improved response and fuel consumption has been achieved by electronic control multipoint
fuel injection.
l Water-cooled turbocharger.
Quiet operation
l Noise and vibration have been decreased by the adoption of roller rocker arms.
l Noise generated by the valve mechanism has been decreased by the hydraulic auto lash adjusters.
l Vibrations have been decreased by the adoption of bearing caps with beams which increase the
rigidity of the crankshaft support points.
-Serviceability
l Complete self-diagnosis functions.
l Enhanced reliability through the adoption of gold-plated connector terminals.
l Use of an auto tensioner achieves maintenance-free, automatic adjustment of timing belt
tension.
l Use of the auto lash adjusters achieves maintenance-free, automatic adjustment of valve clearance
.o The 2coil ignition system without a distributor supplies sufficient ignition energy even during
high speed operation.

_--
8-4ELECTRICAL - Fuses / Diagnosis System
61543
2
16R133lDEDICATED FUSES
For high-load circuits, fuses dedicated to each individual circuit
are used.
The dedicated fuses are provided in the relay box of the engine
compartment.
No.
I
Circuit
I
H,“d;;-;I
Rated
canacitv (A)I
1 1 Tail light circuitIRedI10I
2Fog light circuitRed10
3,.Hazard warning light circuitRed10
4 ) Upper beam circuitIRedI10I
5’
I
Air conditioner magnet
I
Red
I
10
clutch circuitI
6’Condenser fan motorYellow20
circuitI
NOTEl : Air conditioner equipped models.DIAGNOSIS SYSTEM
- CHECK CON-
NECTORS
nmcwaBThe connectors for diagnosis of the following systems are
provided beside the junction block.
1. Multi-point Fuel injection System
2. Automatic
Transaxle.3. Diagnosis control
z. grm.rlnaFd vehicle speed
6: Auto-cruise control
:..--.-__-.

ENGINE- Base Engine9-11 7Oil jet
Front mark
6ENOO6lCONNECTING ROD
(1) The same connecting rod is used as that used in the 4663SOHC engine.
(2) The oil jet provided in the shoulder of the connecting rod is
used to lubricate the cylinder wall.
(3) The big-end bearing is the kelmet metal with metal backing.
CRANKSHAFT(1) The crankshaft is supported by the five main bearings.
(2) The oil passages drilled to the crankpins permit the flow of
lubricating oil from the main bearing to the connecting rod
bearing.(3) The crankshaft has been subjected to special surface
treatment. Therefore, do not grind it for reuse.
(4) The main bearing is an aluminum alloy with a backing of
another metal. The center bearing is provided with flanges
to receive the thrust load of the crankshaft.
Oil passage
6EN0089
16ENOOQO
Oil passage
INo. 51MAIN BEARING CAPSThe No. 1 and No. 2 main bearing caps are joined, as are the
No. 4 and No. 5 main bearing caps, by means of a beam to
minimize vibration of the bearing saddles and to enhance
rigidity of the crankshaft support.
--
.--. _A