1990 MAZDA 232 fuel pump

F2 FUEL SYSTEM
93GOF2-775
1 93GOF2-78(
93GOF2-78:
1
93GOF2-78;
-
93GOF2-783
FUEL PUMP RESISTOR/RELAY
System Operation
I. Remove the rear seat cushion.
2,
Measure the voltage at the fuel pump connector terminal
A {G/O).
Voltage
r Crankinq Approx. 12V
I
I- Others t ACKXOX. I OV i
3. If not within specification, perform the following inspection,
and repair or replace if necessary.
l Fuel pump resistor/relay resistance. (Refer to below.)
l ECU II terminal voltage. (Refer to page F2-60.)
l Wiring harness and connector.
inspection
1.. Disconnect the connector.
2. Ground the fuel pump resister relay terminal D.
3. Apply 12V to terminal C and check for continuity between
terminals A and B.
Terminal C
12 applied
ov Continutty between A and B
NO
Yes
4. Measure the resistance between terminals E and F.
Resistance : 0.62-0.66Q [at 20% (68OF)l
INJECTOR
Volume Test
1. Remove the injectors with the delivery pipe.
2. Affix the injectors to the delivery pipe with wire.
Caution
l Affix the injectors firmly to the delivery pipe so that
no movement of the-injectors is possible.
Warning
l Be extremely careful when working with fuel.
Always work away from sparks or open flames.
3. Connect the SST to the battery and injector.
4. Check the injection volume with a graduated container.
Injection volume:
BP SUHC....44-47 cc (2.68-2.87 cu in)/15 sec.
BP Turbo
. ...87-105 cc (5.31 -6.41 cu in)/15 sec.
Caution
l When using the SST, make sure of the SST num-
ber and use correct one.
5. If nut correct, replace the injector(s).

F2 CONTROL SYSTEM
Terminal voltage [BP TURBO]
eminal input Output , 1 Connected to Test condition Correct voltage Remark
IA - - Battery Constant Approx. 12V for backup
15 0 Main relay OFF Approx. OV
(FUEL INJ relay) tgnltlon switch
-
ON Approx. 12V
1c 0 1 Ignition switch Wniie cranking Approx. 1 OV
-
(START)
lgnrtron switch ON Approx. OV
ID 0 Self -Diagnosis Test switch at “SELF-TEST” With Self-
Checker Lamp illuminated ior 3 sec. after ignition Approx. 5V Diagnosis Check-
(Monitor lamp) switch OFF* ON er and System
Lamp not illuminated after 3 sec. Approx. 12V Se’ector
Test switch at
“02 MONITOR” at idle
Monitor lamp illuminated Approx. 5V
Test switch at
“02 MONITOR” at idle
Monitor lamp not illumrnated Approx. 12’4
-lE - - - -
- -
1F 0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2.5V l With Self-
Checker switch OFF -+ ON Diagnosis
(Code Number)
Buzzer not sounded after 3 sec. Approx. 12V Checker and
Buzzer sounded Below 2.9 System Selector
l With System
Buzzer not sounded Approx. 12V Selector test
switch at
“SELF-TEST’ ’
I I 1G
0 Igniter
7H
0 Solenoid vahe
(Wastegate)
l!
0 Fuel pump
resistor/relay
I
lJ I r-Tcreiay Ignition switch ON
ld!e
Engine speed below 5,300 rpm
Engine speed above 5,300 rpm
While cranking
Idle
Ignition switch ON
AK switch ON at idle 1 Approx. OV
-
Approx. 0.2V
Approx. 12V
-
Below 1.5V
Approx. 1 OV
-
I3elow 15V
Approx. 12V
Below 2.5V
AIC switch OFF at idle Approx. 12V
-
IK 0 Diagnosis System Selector test switch at
connector
(TEN terminal)
1L - - -
- -
-
IM
t 0
1 Ground (Australia) Constant Below 1 .OV Not used
(Except Australia)
F2-60

CONTROL SYSTEM F2
Incorrect voltage Possible cause
Always OV
l ROOM 10A fuse burned l Open circuit in wiring from ROOM 10A fuse to ECU termrnal IA
Always OV
I l Main relay maifunctlon l Open or short crrcu~t in wirrng from main relay to ECU termrnal 1 B
Always OV (Srarrer turns)
l Open or short circuit in wiring from ignition switch to ECU terminal 1C
Always UV
l Main relay (FUEL INJ relay} malfunctron l Open circuit in wiring from main relay to diagnosis connector terminal + B l Open or short circuit in wiring from dragnosls connector terminal MEN to
ECU terminal 1D
Always approx. 12V
I . Poor connection at ECU connector
l ECU matfunction
Always approx. 5V
l ECU malfunction
-
I -
Always below No disptay on Self- . Main relay (FUEL INJ retay) malfunction (Refer to page F3-142)
2.5V Diagnosis Checker l Open circuit in wiring from main relay to diagnosis connector termjnal + B
“88” displayed and
l Open or short circuit in wiring from diagnosis connector terminal FEN to
buzzer sounds con- ECU terminal 1 F
tinuously
Always approx. 12V
l Poor connection at ECU connector l ECU malfunction
Always OV
l Short circuit in wiring from igniter to ECU terminal tG
Atways OV or approx. 12V
l Refer to Code No.42 Troubleshooting (Refer to page F2-30)
Always approx. 12V
l Fuel pump resistor/relay malfunction
Always OV
l Open or short circuit in wiring from ECU terminal 1 I to resistor/retay
Always below
A/C does not operate
l AJC relay malfunction
23 l Open circuit in wiring from ignition switch to NC relay l Open circuit in wiring from A/C relay to ECU terminal IJ
A/C switch OFF but
l Short circuit in wiring from A/C relay to ECU terminal IJ
AIC operates
l ECU matfunction
Always approx. t2V
Always below 1 .OV
l Poor connection at ECU connector l ECU malfunction
l Short circurt in wiring from diagnosis connector terminal TEN to ECU termi-
nal 1K
Always approx. 12V
l Open circutt in wiring from diagnosis connector terminal TEN to ECU termi-
nal lK
l Open c~rcud in wiring from diagnosis connector terminal GND to ground
Always above 1 .OV
I
l Open circuit in wiring from ECU terminal 1 M to ground
F2-61