1990 MAZDA 232 torque

INSTALLATlON
MTX 1 A-I-X
WUOBX-828
43GOBl-72t
Step 3
Torque Specifications 8. Tighten bolts @ in two or three steps in the order shown.
Tightening torque:
43-61 N-m (4.4-6.2 m-kg, 32-43 ft-lb)
9. Tighten nuts @J.
Tightening torque:
67-93 N-m (6.8-9.5 m-kg, 49-69 ft-lb)
IO. Tighten the No.3 engine mount nuts 0.
Tightening torque:
74-103 Nom (7,5--f0,5 m-kg, 54-76 ft-lb)
Ii. Tighten nut @.
Tightening torque:
67-93 N-m (6.8-9.5 m-kg, 49-69 ft-lb)
12. Install the dynamic damper.
Tightening torque:
55-W N-m (5.6-8.2 m-kg, 41-59 ft-Ib)
13. Remove the chain hoist.
6.9-11 N-m (70-l 10 cm-kg, 63-95 in-lb)
-8-3.1, 20-22)
&TX 6.9-11 N-m (70-130 cm-kg,
b 6% -95 in-lb) /
42-57 (4.3~5.8,31142)
21-27 (2.1-2.8, 15-20)
COTTER PIN, REPLACE
16-23 (1.6L2.3, Q-17)
N-m {m-kg, ft-tb
03UOBX-8:

81 INSTALLATION
93GOBl-714
I 93E082-061
i 03UOBX-848
Propeller shaft
1. Install the propeller shaft. (Refer to page l-5.)
Driveshaft
I. Apply grease to the end of the driveshafi.
Caution
l When installing the driveshaft, be careful not to
damage the transaxle oil seal.
l After installation, pult the front hub outward to con-
firm that the driveshaft is securely held by the cIip.
2. Install the driveshaft along with a new clip.
3. fnstall the lower arm ball joint to the knuckle and tighten the
ciinch bolt.
Tightening torque:
43-59 Nm (4.4-6.0 m-kg, 31-43 ft-lb)
4. Install the joint shaft.
5. Tighten the bolts in the order shown.
Tightening torque:
42-62 Nom (4.3-6.3 m-kg, 31-46 f&lb)
Tie-rod end
1. InstaIl the tie-rod end to the knuckle.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
2. Install a new cotter pin.
Stabilizer
I. install and adjust the stabilizer.
Dimension A: i7-19mm (0.67-0.75 in)
Tightening torque:
16-23 Nm (l-6-2.3 m-kg, 12-17 Mb)
I
I

--
D
b
D
1
I
1
(
I
INSTALLATION Bl
Exhaust pipe
I. Instail the exhaust pipe along with a new gasket; then loosely
tighten locknuts @.
2. Loosely tighten bracket nuts @
3. Tighten locknuts 0.
Tightening torque:
3f-46 N-m (3.2-4.7 m-kg, 23-34 f&lb)
4. Tighten bracket nuts @.
Tightening torque:
21-27 Mm (2.1-2.8 m-kg, 15-20 ft-Ib)
Select and shift cables (MTX)
7 _ Install the select cable and the spring pin.
2. Install the shift cable and the spring pin.
03UO8X-835
Shift control cable (ATX)
1. Install the shift control cable and the spring pin.
Tightening torque:
6.9-l 1 Nom (70-l 10 cm-kg, 61-95 in-lb)
Speedometer cable
1. Connect the speedometer cable.
t

I)
I)
i
INSTALLATION Bl
Step 6
Torque Specifications
7.8-11 N-m (8U---110 cm-kg, 69-95 in-lb) 19-25 (1.9-2.6, 14-19)
37-S (3.8-5.3, 27-38)
7.8-71 N-m
(80-l 10 cm-k
19-25 (1.9-2.6, 14-
5-1 1.9, 69-79)
-9.3 N-m (65-95 cm-kg, 56-82 h-lb) -79)
7.8-11 N-m (80-1~0 cm-kg, 69-95 in-lb)
a3uar3x-839
Crossmember
1. tnstali the crossmember.
Tightening torque:
93-107 Nm (9.5-I 1.9 m-kg, 69-79 f+lb)
NC compressor
1. Install the A/C compressor.
Tightening torque:
24-35 N-m (2.4-3.6 m-kg, 17--26 ft-lb)
Bl-21

Bl INSTALLATION
93GOE 1-73;
03UOBX-84
. .
‘, .
L .G,
. . ‘?.
- -. _ .:
.L ‘.. :-.:
.-_: _. _, _-
.
-_
. :
Cl :- . .
: .._.
. . ._-
;: , ‘. ’
,.. .- -
. ‘L,
93GO3 l-73’
-DEFLECTiON CHfiCKIN:
g3GOBj-717
Bl-22
P/S oil pump and bracket
1. Install the P/S oil pump and bracket.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
Drive belt
I. fnstall the P/S and/or A/C drive belt.
2. Adjust the drive belt deflections. (Refer to page Bl-2.)
Radiator
and cooling fan assembly
f . Install the radiator and cooling fan assembly.
Tightening torque:
7.8-I 1 N-m (80-I 10 cm-kg, 69-95 in-lb)
2.. Connect the cooling fan connector.
3. Connect the radiator switch connector.
4. Connect the A/C cut switch connector.
5. Connect the oil cooler hose. (ATX)
6. Connect the coolant reservoir hose.
7. Connect the upper and lower radiator
@TX)
Pm
hoses.
Caution
l Position the hose clamp in the original location on
the hose, and squeeze it tightly with large pliers to
ensure a good fit.
Accelerator cable
I. Install the accelerator cable.
2. Adjust the cable deflection by turning nuts @
Deflection: I-3mm (0.04--0.12 in)
-
Battery duct, battery carrier, and battery
I_ install the battery duct.
2. Install the battery carrier.
Tightening torque:
7.8-I 1 N-m (80-110 cm-kg, 69-95 in-lb)
3. Install the battery, cover and the battery bracket.
Tightening torque:
2.9-5.9 N-m (30-60 cm-kg, 26-52 in-lb)
4. Connect the positive battery cable.

INSTALLATION Bl
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 Nm (I-9-2.6 m-kg, 14-19 Mb)
@: 7.8-11 Nm (80~-110 cm-kg, 69-95 in-lb)
2. Connect the airflow sensor connector.
Resonance chamber
1. lnstail the resonance chamber.
Tightening torque:
7.8-W Nm (SO-11 0 cm-kg, 69-95 in-lb)
Undercover and side cuver
1. install the undercovers and side covers.
Steps after installation
1. If the engine oil was drained, refill with the specified amount and type of engine oil.
2. Fill the radiator with the specified amount and type of engine coolant.
3. Fill the transaxle with the specified amount and type of transaxle oil. (Refer to pages J3-36, K3-134.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage
(2) Ignition timing and idle speed
(3) Operation of emission control system
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
93GOSi-719
al-23

B2 INDEX
INDEX
~IMIY~ULU
TIGHTENING TORQUE
19-25 (1.9-2.6, 14-19)
/5--l ENGINE COMPRESSION
STANDARD
MINIMUM kPa (kglcm2, psi)-rpm
BP Turbo
I
1,059 (10.8, 1543-300
1 i-85 (8.0, 114)-300
EXHAUST MANlFOt
TIGHTENING TORQUE
DEFLECTION AT 98 N (IO kg, 22 Ib)
mm (in)
DRIVE BELT 1 NEW USED
ALTERNATOR 1 8.0-9.0 (0.31-U.35) 9.0-I 0.0 (0.35-U.39)
P/S, P/S + AIC ( 8.U-9.0 [O-31--0.35) 9.0-10.0 (0.35-0.39) 3826 3.9-A.?, -28134)
1. Engine
Removal -*-...-..I-*.* . ..wm._..... * e-e... -. page B2--I 2
Engine stand mounting ._.....__... page B2-20
Engine stand dismounting . . . . . . . page B2-21
Installation _ . . . . . . . . . . . . , . . _. . . . . . _. . . . . . . . , page EQ-23
BZ-2

D
D
SUPPLEMENTAL SERVICE iNFORMATION, COMPRESSION 82
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison with Workshop Manual [Europe (7 203~IO-899,
Australia (I 204-1 U-89F) 1.
Compression
l Inspection
Engine
l Removal
l Engine stand mounting
l Engine stand dismounting
l Ins:attaIion 93GQ32-77 I
COMPRESStON
If the engine exhibits low power, poor fuel economy, or poor idle, check the following:
1. Ignition system (Refer to Section G.)
2. Compression
3. Fuel system (Refer to Section F3.)
93G032-774 93GO32-712
1NSPECTION
1. Verify that the battery is fully charged. Recharge it if
necessary.
2. Warm up the engine to normal operating temperature.
3. Turn the engine OFF.
4. Remove all of the spark plugs.
5. Disconnect the ignition coil connector.
6. Connect a compression gauge to the No.7 spark plug hole.
7. Fully depress the accelerator pedal and crank the engine.
8. Record the maximum gauge reading.
9. Check each cylinder in the same manner.
Compression:
1,059 kPa (IO.8 kg/cm2, 154 psi)-300 rpm
Minimum:
785 kPa (8-O kg/cm2, 114 psi)-300 t-pm
Allowable difference between cylinders:
196 kPa (2.0 kglcm2, 28 psi) max.
IO. If the compression in one or more cylinders is low, pour a
small amount of engine oil into the cylinder and recheck
the compression.
(1) If the compression increases, the piston, piston rings,
or cylinder waII may be worn.
(2) If the compression stays tow, the valve may be stuck
or seating improperly.
(3) If the compression in adjacent cylinders stays low, the
cylinder head gasket may be defective or the cylinder
head distorted.
1 I. Connect the ignition coit connector.
12. Apply antiseize compound or molybdenum-based lubricant
to the spark plug threads.
73. Install the spark plugs.
Tightening torque:
15-23 N-m (1.5-2.3 m-kg, If-17 ft-Ib)
82-11