A PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
pieziG-
INSPECT and ADJUST, if necessary, the following Items to
specification:
D Glass, exterior bright metal and paint for damage
Cl Wheel tug nuts
9 Trre pressures
LII All weatherstrips for damage or detachment
Z Operation of bonnet release and lock
D Operation of trunk lid, hatch and fuel lid opener
(it equipped)
3 Door operation and alignment
5 Headlight aiming
INSTALL the following parts:
D Wheel caps or rings (if equipped)
D Outside mirror(s)
[ UNDER BONNET-ENGINE OFF )
INSPECT and ADJUST, if necessary, the foIlowIng items to
specification:
Cl Fuel, coolant and hydraulrc lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level (if equipped)
D Brake master cylinder fluid levels
0 Clutch master cylinder fluid levels (if equipped) q
Windshield washer reservoir fluid level
D Radiator coolant level and specific gravity
Ll Tightness of water hose clamps
I3 Tightness of battery terminals, electrolyte level and specific
gravity
c) Manual transaxle oit level
D Drive belt(s) tension
C; Carburetor linkage (choke control, wide open throttle posi-
tion, etc.) (carburetor model only)
D Accelerator cable and linkage for free movement
D Headlight cleaner and fluid level (if equipped)
BLEED air from fuel line (diesel engine only)
CLEAN the spark plugs (except for diesef engine)
piicis-1
INSTALL the foflowing parts:
C Rubber stopper for inside rear view mirror (if equipped)
c! Fuse for accessories
CHECK the operation of the following items:
Cl Seat controls (sliding and redining) and head rest
ci Seat belts and warnrng system
Z! Ignition swrtch and steering lock
III Power window {if equipped)
0 Door locks including child proof door locks
0 Inhibitor switch
(ATX only)
Z All lights including warning and indicator lights
0 Ignrtron key reminder buyer (if equipped) Cl Horn, wipers and washers (front and rear, if equipped)
D Antenna (if equipped} q
Cigarette lighter and clock (if equipped)
I2 Remote controt outside mirror
(if equipped) q
Heater, defogger and air conditioner at various mode selec-
tions (if equipped)
c3 Sunroof (if equipped)
CHECK
the fotiowing items: q
Presence of spare fuse
c3 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
Cl Operation and fit of windows
D Pedal height and free ptay of brake and clutch pedal
Cl Parking brake
i UNDER BONNET-ENGtNE RUNNING AT ]
1 OPERATtNG TEMPERATURE
CHECK the following items:
Cl Operation of idle-up system for air conditioner or power steer-
ing (if equipped)
13 Automatic transaxle fluid level
D Initial ignition timing
(except disel engine) q
Idle speed
El Operation of throttle position sensor (EGI engine)
13 Operation of cold start device and glow plug warning light
(diesel engine only)
D Operation of dash pot [EGI engine)
t
ON HOtST 1
CHECK the following items:
U Underside fuel, coolant and hydraulic lines, fittings, connec-
tions and components for leaks q
Tires for cuts or bruises
Cl Steering linkage, suspension, exhaust system and all under-
side hardware for
looseness or damage
1 ROAD TEST 1
CHECK the foliowing items:
II Brake operation
D Clutch operation
0 Steering control
c3 Operation of meters and gauges
0 Squeaks, rattles or unusual noises q
Engine general performance
c3 Emergency Iocking retractors
rAFTER ROAD TEST 1
REMOVE the seat and floor mat protective covers
CHECK for the necessary
owner information materials, tools
and spare tire in vehicle
93EOAX-002
A-2
H OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
A hydraulic clutch control mechanism is used.
The basic construction is the same as that of 323 2WD model, but there is no interchangeability of parts
except for the release cylinder.
1. An assist/return spring is used on the BP DOHC Turbo model to reduce the required clutch pedal effort..
2. The hydraulic clutch master cylinder for the 8P DOl-lC Turbo model has a built-in check valve.
3. To improve clutch operation feeling and increased parts life, a friction plate and needle roller bearings
are used between the release fork and the release bearing.
93GOHX-704
SPECIFICATIONS
Hem
Clutch control Engine/Transaxle
BP SUHC BP DOHC Turbo
GSMX-R
Hydrautic
Clutch cover
Type
Set load
N (kg, lb) Diaphragm spring
3,846 (392, 862) 5,494 (560, I ,232)
Outer diameter 1
mm (in) 225 (8.858) 230 (9.055)
I 1 nner diameter mm (in)
I 150 (5.906)
I 155 (6.102) I
CI utch disc
Pressure plate side
mm {in) 4.1 (0.161) 3.2 (0.126)
Thickness f
Flywheel side
mm (in) 3.5 (0.138) 3.2 (0. f 26)
I Type I Suspended
I
Clutch pedal LHD 6.55 Pedal
ratio
RHD 6.7
Full stroke mm (in)
I 135 (5.32)
I
Height (With carpet) mm [in)
I I 96-204 (7.72-8.03)
I
Master cylinder Inner diameter
mm {in)
I 15.87 (0.625)
Release cylinder inner diameter
mm (in)
I - 19.05 (0.750)
I
Clutch fluid SAE J1703 or FMVSSI 16 DOT-3
93GOHX-705
H-4
