1990 MAZDA 232 engine

SUPPLEMENTAL SERVICE INFORMATION, TROU8LESHOOTlNG GUIDE H
SUPPLEMENTALSERVICE INFORMATION
The following points in this section are changed in comparison with 323 Workshop Manual (1206IO-89F).
Troubleshooting guide
Clutch fluid (with ABS)
l Replacement
Clutch pedal (BP DOHC Turbo) Clutch release cylinder (with ABS) l Air bleeding
Clutch unit
l Removal I Inspection I installation
Clutch master cylinder
(BP DOW Turbo or with ABS) l Removal I Inspection I installation
93GOHX-710
l Removal I Inspection I Installation (BP DUHC Turbo)
l Air bleeding (with ABS)
l Overhaul (BP DUHC Turbo)
TROUBLESHOOTING GUlDE
Problem
Possibte Cause Remedy Page
Slipping
Clutch disc facing worn excessively
Replace U-l 9
Clutch disc facing surface hardened or oifed
Repair or replace H-l 9
Pressure plate damaged Replace H-19
Diaphragm spring damaged or weakened
Replace H-l 9
Insufficient clutch pedal piay
Adjust H-12
Clutch pedal sticking
Repair or replace U-11
Flywheel damaged
Repair or replace H-19
Faulty
Excessive runout or damaged clutch disc
Replace H-19
disengagement
Clutch disc spiines rusted or worn ’
Remove rust or replace H-l 9
Clutch disc facing oiled
Repair or replace H-19
Diaphragm spring weakened
Reptace H-19
Excessive clutch pedal ptay
Adjust -
Insufficient clutch fluid
Add fluid H-10
Leakage of clutch fluid
Locate and repair or -
replace
Clutch vibrates
Clutch disc facing oiled
Repair or replace H-l 9
when accelerating
Torsion rubbers weakened
u-19 Clutch disc facing hardened or damaged Replace
Repair or replace H-19
Clutch disc facing rivets loose
Replace H-l 9
Pressure plate damaged or excessive runout
Replace H-l 9
Flywheel surface hardened or damaged
Repair or replace H-19
Loose or worn engine mount
Tighten or replace -
Clutch pedal
sticking Pedal shaft not properly lubricated
Lubricate or replace H-l 1
Asistireturn spring damaged or poor adjust
Replace or adjust H-11, 12
Abnormal noise
Clutch release bearing damaged
Replace N-1 9
Poor iubrication of release bearing sleeve
Torsion rubbers weakened Lubricate or replace H-19
Replace u-t9 Excessive crankshaft
end play
Repalr -
Pilot bearing worn or damaged
Replace H-79
Worn pivot points of reiease fork
Repair or replace H-19

J3 OUTLtNE
OUTLINE OF CONSTRUCTION
l Full-time 4-wheel drive, incorporating a viscous coupling is used on the BP DUHC Turbo model. BP SUHC
engine equipped models are fitted with an electronically controlled, lockable center differential.
With this system all driving conditions are easily contended with; from good roads to bad roads and
ad-
verse weather conditions.
l The transaxle and transfer unit were developed based on the GSM-R type transaxle.
The transaxle, center differential, viscous coupling, and front differentia! are a single, compact unit.
l The center differential employs a planetary carrier. system and a viscous coupling, and functions to distrib-
ute the driving force to the front and rear differentials as needed.
Through the use of this center differential, tire scuffing common to 4-wheel drive vehicles during tight cor-
nering, is eliminated.
l The speedometer driven gear (for detection of vehicle speed) is installed in the transfer carrier and detects
the speed of the rear wheels.
l Lubrication oil of the transaxle and transfer unit and of the carrier is contained separately.
93GOJ3-704
J3-4

OUTLINE 33
SPECIFICATIONS
TRANSAXLE AND TRANSFER UNIT
Item Engine model
Transaxle control
Forward
Synchromtsh system
Reverse
I St
2nd
3rd
Gear ratlo 4th
5th
Reverse
Final gear ratio
Speedometer gear ratlo
Type
Number of ring Outer
gear teeth
Inner
Center differential
gear teeth
Inner
Number of sun Pinion gear side
gear teeth
Idler gear side
Number of idler gear teeth
Type
011
Capacity BP DOHC turbo BP SOHC
Floor shift
Synchromesh
Selectrve sfiding and synchromesh
3.454 3.307
1.833
I.310 1.233
0.970 Cl.91 4
0.717
3.166 L
4.214 4.388
1 .oo
Planetary carrier
59 79
75 66
14
14
43 33
43
37
ATF: DEXRON-II, M-III Above -18OC (O°F)
API servie GL-4 SAE 75W-90
2.6 liters (2.7 US qt, 2.2 Imp qt)
93GOJ3-305
Transfer Carrier
Number of teeth Ring gear
Pinion gear 37
11
API service GL-5
Oil Type
Capacity Above -18OC tOoF) SAE 90
Below -18OC tOoF) SAE 8OW
0.5 liter (0.53 US qt,
0.44 Imp qt)
93GOLl3-776 -
J3-5