1988 JEEP CHEROKEE battery

Fig. 28: Installing & Aligning Rotor
Courtesy of Chrysler Motors.
6) Carefully slide the distributor into the block until it
seats, keeping the hold down ear aligned to the hole in the block.
7) The rotor should be in the 5 o'clock position with the
trailing edge of the rotor blade lined up with the mark previously
scribed on the distributor housing (number one spark plug wire post
location).
8) install the distributor hold-down clamp bolt and tighten
to 9.5-14 Ft. Lbs. (13-19 N.m).
9) Install the distributor cap. Connect the distributor
electrical connector.
10) Install the electric cooling fan and shroud if
applicable.
11) Connect the negative battery cable.
IGNITION/COIL WIRE REPLACEMENT PRECAUTIONS

\003
IN STR UM EN T P A N EL - S TA N DAR D

1988 J e ep C hero ke e
1988 Switches & Instrument Panels
JEEP
DESCRIPTION & OPERATION
Instrument panel is composed of speedometer housing,
tachometer and instrument cluster gauges.
FUEL GAUGE
System consists of a fuel gauge, an in-tank sending unit, and
appropriate wiring. Fuel gauge is grounded through variable resistor
of sending unit. A float attached to a slide rheostat follows fuel
level and varying resistance increases or decreases indicator reading.
TEMPERATURE GAUGE
System consists of gauge and sending unit and appropriate
wiring. The gauge is grounded through variable resistor of sending
unit. Changes in coolant temperature vary resistance in sending unit,
increasing or decreasing indication on gauge.
VOLTMETER
The voltmeter indicates regulated voltage to provide an
indication of charging system's ability to maintain battery charge.
OIL PRESSURE GAUGE
The oil pressure gauge system consists of gauge and a
variable resistance sending unit. Gauge needle, attached to bi-
metallic strip, responds to temperature changes.
REMOVAL & INSTALLATION
INSTRUMENT CLUSTER
Removal & Installation
1) Disconnect negative battery cable. On models with cruise
control, reach behind instrument cluster and disconnect speedometer
cable from speed switch. See Fig. 1.
2) On models without cruise control, raise vehicle on hoist.
Disconnect speedometer cable from transfer case (or transmission) and
at frame rail bracket. Move speedometer cable forward and upward to
provide slack. Lower vehicle.
3) On all models, remove instrument panel bezel screws and
bezel. Remove screws attaching cigarette lighter and switch housings
to instrument panel. Move housings aside.
4) Remove screws attaching cluster to instrument panel and
carefully pull cluster and speedometer toward rear of vehicle.
Disconnect wiring harness connectors.
5) Squeeze speedometer cable locking tabs and disconnect
cable from speedometer. See Fig. 1. Remove instrument cluster. To
install, reverse removal procedure.

MAIN TE N AN CE IN FO RM ATIO N

1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance Information
Jeep; Cherokee,
Wagoneer
* PLEASE READ THIS FIRST *
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
* SCHEDULED SERVICES - GASOLINE
* SCHEDULED SERVICES - DIESEL ENGINES - NORMAL (1985-87)
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
See VIN example below.








\









\









\









\









\









\








 
(VIN) 1 J C U N 7 7 1 X G T 0 0 0 0 0 1 


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 










\









\









\









\









\









\








1 - Manufacturing Country
1
* United States
2 - Company/Make
J * American Motors/Jeep
3 - Type
C * Multi-Purpose Vehicle
D * Incomplete Vehicle
E * Export, LHD
F * Export, RHD
4 - Engine Type
B * 2.1L (128 CID) 4-Cylinder Turbo (Diesel) (001B) (1985-87)
H * 2.5L (150 CID) 4-Cylinder TBI (Gasoline) (001H) (1986-88)
U * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Gasoline) (001U) (1984-85)
Y * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Export) (001Y) (1984-85)
W * 2.8L (171 CID) V6 2-Bbl. (Gasoline) (001W) (1984-86)
M * 4.0L (242 CID) I-6 (Gasoline) (001M) (1987-88)

BATTERY SPECIFICATIONS
CAUTION: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See COMPUTER
RELEARN PROCEDURES article in the GENERAL INFORMATION
section.
All gasoline engine equipped models use group 58 batteries
with 390 or 475 amp cold crank rating. Models with 2.1L Turbo Diesel
engine use group 24 batteries with a 815 amp cold crank rating.
CAUTIONS & WARNINGS
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See COMPUTER
RELEARN PROCEDURES article in GENERAL INFORMATION section.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
DIESEL FUEL ANTI-FUNGAL ADDITIVES
CAUTION: If fuel contamination due to fungi or other microorganisms is
suspected a fuel additive with a biocide may be used. Follow
the manufacturers dosage as recommended on product label. Use
biocides ONLY when necessary, excessive use can may cause
other fuel system problems.
DIESEL FUEL CONTAMINATION
WARNING: Diesel fuel system may be contaminated with fungi or other
microorganisms. Keep contaminated fuel away from open skin
cuts or sores to prevent skin irritation or infection.
DIESEL FUEL REQUIREMENTS
CAUTION: All diesel engines are to use Diesel Fuel #2 when the outside
temperature is above 20\bF (-7\bC). In temperatures that are
below 20\bF (-7\bC) use Diesel Fuel #1, this will reduce the
chance of the fuel thickening and forming wax.
Note: A Diesel Fuel #1 & #2 combination (Blended Fuel) may be\
used, and is recommended for mild winter driving.

\003
MIR RO RS - P O W ER

1988 J e ep C hero ke e
1988 Power Mirrors
JEEP
DESCRIPTION
Outside power rear view mirrors consist of door-mounted
mirrors with internal motor drive and backing plate. The Ford
electronic day/night mirror will change from normal to non-glare
position when glare reaches mirror. The non-glare functions only at
night.
TESTING
Mirror Motors & Switches
1) Ensure fuse is okay by operating interior lights. If
neither mirror operates, check for battery voltage at power mirror
switch assembly. Connect a voltmeter between terminal "G" (Red with
White stripe) and ground. If battery voltage is present, connect
voltmeter between terminals "G" and "F" (Black). If battery voltage is\
not present, check circuit at Red with White stripe wire and Black
wire.
2) If one mirror does not operate, connect a voltmeter across
power mirror switch assembly terminals. See Fig. 1. Voltage will be
present when control switch and mirror select switch are operated for
that motor.
Fig. 1: Jeep Switch Assembly Check Chart
Courtesy of American Motors/Jeep Corp.
3) If voltage is present but mirror does not operate, check
motor and wiring. If voltage is not present when 2 switches are on,

If test light glows, check tailgate window motor.
TAILGATE WINDOW MOTOR
Grand Wagoneer
1) Using a 12-volt test light, connect one end of test light
to ground and probe Tan wire at motor. Close safety switch and turn
tailgate window switch to "DOWN" position. If test light glows and
motor does not operate, replace motor. If test light does not glow,
check feed circuit to motor and repair as necessary.
2) Probe Brown wire at motor. Close safety switch and turn
tailgate window switch to "UP" position. If test light glows and motor
does not operate, replace motor. If test light does not glow, check
feed circuit to motor and repair as necessary.
SIDE WINDOW MASTER SWITCH CIRCUIT
1) Remove escutcheon and housing from master switch. Separate
terminal plate by releasing retainer hooks to expose terminal ends.
Turn ignition on.
2) Using a 12-volt test light, connect one lead to Black wire
and other lead to Red terminal. Repeat test at second Black wire. If
test light does not glow in either test, remove lead to Black terminal
and connect to chassis ground.
3) If test light glows, an open exists between master switch
and ground. If test light does not glow, it indicates a defective
circuit breaker or an opening in the Red wire from circuit breaker to
master switch.
SIDE WINDOW CONTROL SWITCH & MOTOR TEST
Grand Wagoneer
1) Connect test light between terminals of Orange and Yellow
wires. Operate control switch up and down. If test light glows in both
switch positions, wires, individual door and master switches are not
defective.
2) Disconnect White and Green motor leads at terminal plate,
and connect to Green and White leads. Operate master switch. If window
goes up and down, motor is okay, but switch is defective. If motor
does not operate, remove trim panel and check connections and leads to
motor. If motor operates, switch is defective.
SIDE WINDOW MOTOR
Connect test battery positive lead to one of the motor
terminals. Connect negative lead to other terminal. Motor should
rotate in one direction to go up or down. Reverse battery leads, motor
should rotate in opposite direction. If window does not move, replace
motor.
SWITCH VOLTAGE TEST
1) Turn ignition on. Remove switch from trim panel.
Disconnect terminal block on wiring harness from switch body. Connect
one lead of test light to Red wire terminal and other end to ground.
2) If test light glows, wiring between battery and switch is
functional. Check continuity in Black wire (ground). If test light
does not glow, check circuit breaker. If okay, check for a broken
wire.
SWITCH UP & SWITCH DOWN TEST

TAILGATE WINDOW REGULATOR & MOTOR
Removal (Grand Wagoneer)
1) Remove carpet (if equipped) and tailgate access cover.
Remove retainers attaching regulator arms to channel. Disengage
regulator arm pins from channel, and raise glass.
2) Carefully support glass in raised position. Disconnect
wiring harness from safety switch. If regulator attaching screws are
covered by sector gears, place a jumper wire between terminals of
safety switch connector.
NOTE: If regulator attaching screws are accessible, remove
regulator attaching screws and regulator.
3) Place key in tailgate switch and operate motor until
regulator attaching screws are accessible. Hold regulator in this
position, and wedge a screw between meshing teeth.
4) Remove regulator attaching screws and regulator. Using a
large screwdriver, release spring tension from tension bracket. Remove
motor attaching screws and motor.
Installation
To install, reverse removal procedure.
SIDE WINDOW MASTER SWITCH
Removal
1) Disconnect battery negative cable. Remove retaining screws
and escutcheon. Remove switch housing screws.
2) Pull switch out to expose wires. Disconnect terminal plate
from switch. Depress retainer clips through holes in switch housing,
and remove switch.
Installation
To install, reverse removal procedure.
FRONT & REAR DOOR REGULATORS & MOTORS
Removal
1) Raise window half way up. Disconnect battery negative
cable. Remove door trim panel and water shield.
2) Insert a drift punch into hole in door inner panel, or use
masking tape to hold window half way up. Remove regulator arm retainer
clip, and remove arm from bottom window channel.
3) Disconnect wires from motor. Remove inner door panel-to-
regulator nuts and bolts. Remove regulator and motor assembly.
Installation
To install, reverse removal procedure.

\003
SC HED ULE D S ER VIC ES - G ASO LIN E

1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance & Service Intervals - Gasoline
Jeep; Cherokee, Wagoneer
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see SEVERE SERVICE REQUIREMENTS (PERFORM
W/SERVICE SCHEDULES) for items requiring additional
maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM (If Equipped)
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with