1988 JEEP CHEROKEE water pump

HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards

Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performance ............ .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Connection damaged ...... B .. Require repair or replacement.
Contaminated, affecting
performance ............ A ............ Require replacement.
Corroded internally ..... 1 ............ Suggest replacement.
Dessicant bag
deteriorated ........... A ........ (1) Require replacement.
Further inspection required.
Dessicant at the end of
its useful life
(saturated
with moisture) ......... 1 .. Suggest repair or replacement.
Filter screen torn ...... A .. Require replacement of screen.
Fitting damaged ......... B .. Require repair or replacement.
Fusible plug leaking .... A .... Require replacement of plug.
Inoperative ............. A ........... ( 2) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Pressure relief device
leaking ................ A . Require replacement of pressure
relief device.
Restricted .............. A .. Require repair or replacement.
Sight glass no longer
transparent ............ 2 ... Suggest replacement of drier.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inspect system to determine effects of dessicant bag
deterioration.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.









\









\









\









\









\









\









\


WATER PUMPS (ELECTRIC AUXILIARY)
WATER PUMP (ELECTRIC AUXILIARY) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.

EM IS SIO N C O M PO NEN T ID EN TIF IC ATIO N

1988 J e ep C hero ke e
1988 Exhaust Emission Systems
JEEP SYSTEMS
NOTE: Information not available from manufacturer for Jeep 2.5L
TBI and 4.0L MPFI emission systems.
DESCRIPTION
Several systems are used to control emissions. System usage
depends on model, engine and transmission combinations. Each system
is designed to control vehicle emissions. In addition, specially
calibrated carburetors (carbureted models), fuel injection system,
distributors and modified combustion chambers are used with these
systems.
AIR INJECTION
Air injection system consists of air pump, diverter valve,
check valve, and various air distribution lines necessary to inject
fresh air adjacent to exhaust valves. Injection of fresh air adjacent
to exhaust valves creates an afterburn which further consumes
unburned gases in engine's exhaust.
CATALYTIC CONVERTER (CAT)
Converter is installed in vehicle's exhaust system to aid in
reduction of exhaust emissions. This unit changes unburned
hydrocarbons (HC) and carbon monoxide (CO) into water vapor and
carbon dioxide.
COMPUTERIZED EMISSION CONTROL (CEC) SYSTEM
CEC system closely controls air/fuel ratio through a
feedback system from an oxygen sensor in exhaust system. Major
components of this system include exhaust gas oxygen sensor, vacuum
switches, temperature switches, Micro Computer Unit (MCU), fuel
injection system or computer controlled carburetor (carbureted
models) to maintain a constant air/fuel mixture. For additional
information, see appropriate article in COMPUTERIZED ENGINE CONTROL
section.
EVAPORATIVE EMISSION CONTROL
All models use closed tank (sealed) system, which returns
raw fuel vapors and routes them to intake manifold for burning.
Carbon canister stores vapors until engine draws them off for burning.
OTHER EMISSION SYSTEMS
For additional information on description, operation,
testing and adjusting other exhaust emission systems, refer to the
following articles in this section.

\003
EN G IN E R EM OVA L - 4 -C YL

1988 J e ep C hero ke e
1988 ENGINES
Jeep - Engine Removal - 4-Cylinder
Cherokee, Comanche, Wrangler
4-CYLINDER ENGINES
2.5L
1) Disconnect negative battery cable. Drain cooling system.
Remove air cleaner, lower radiator hose, fan shroud, and engine
compartment light from hood. Scribe hinge locations and remove hood.
Disconnect automatic transmission cooler lines at radiator (if
equipped).
2) Remove upper radiator hose, fan assembly and coolant
recovery hose. Remove radiator and A/C condenser (if equipped). Hold
fan pulley to water pump flange using 5/16" x 1/2" SAE capscrew.
Disconnect heater hoses, throttle linkages, cruise control cable (if
equipped) and Throttle valve rod.
3) Disconnect wires from starter and separate CEC system
wiring harness connector. Disconnect fuel pipe from fuel pump and fuel
return hose from fuel filter. Disconnect hoses from A/C compressor and
power steering pump (if equipped). Drain power steering pump
reservoir. Cap all fittings and hose ends.
4) Remove vacuum check valve from brake booster (if
equipped). Tag and remove all wiring and vacuum lines connected to
engine or accessories. Raise vehicle and remove starter. Disconnect
exhaust pipe from manifold.
5) Remove converter/flywheel housing cover. Remove engine
mount nuts at bracket side. On automatic transmission models, index
mark drive plate and torque converter. Remove drive plate-to-converter
bolts.
6) Remove upper and loosen lower bellhousing-to-engine bolts.
Attach lifting equipment to engine. Raise engine off front mounts,
Place support under bellhousing. Remove remaining bellhousing-to-
engine bolts. Lift engine out of engine compartment.
NOTE: Engine mount pads may be removed from engine brackets to
align engine and transmission during installation.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Clutch Housing-to-Block Bolts .................... 55 (75)
Drive Plate-to-Converter ......................... 26 (35)
Flywheel Bolts ............................... ( 1) 50 (68)
Front Support Bracket-to-Block ................... 45 (61)
Front Support Cushion-to-Crossmember ............. 33 (45)
Rear Support Bracket-to-Transmission ............. 33 (45)
Rear Support Cushion-to-Bracket .................. 30 (41)
Starter Motor-to-Block ........................... 33 (45)
( 1) - Tighten an additional 60 degrees.









\









\









\









\









\









\

\003
EN G IN E R EM OVA L - 6 -C YL

1988 J e ep C hero ke e
1988 ENGINES
Jeep - Engine Removal - 6-Cylinder
Cherokee, Comanche, Wagoneer, Wrangler
6-CYLINDER ENGINES
4.0L
1) Scribe hinge locations, remove engine compartment light
(if equipped) and remove hood. Disconnect battery cables and remove
battery. Drain cooling system.
2) Disconnect wire connectors from alternator, ignition coil
and distributor. Disconnect oil pressure sender wire, starter wires
and fuel injector wiring harness (if equipped). Detach 2 fuel pipe
quick connect couplings at left inner fender panel. Disconnect engine
ground strap and remove air cleaner.
3) Disconnect the vacuum purge hose at fuel vapor canister
tee. Disconnect wire from idle speed actuator and oxygen sensor.
Detach throttle cable from bracket and disconnect throttle valve rod
at bellcrank. Remove upper and lower radiator hoses.
4) On automatic transmission models, disconnect the
transmission fluid cooler tubing. On all models, remove fan shroud and
radiator. Remove fan and spacer or Tempatrol fan assembly. Hold fan
pulley to water pump flange using 5/16" x 1/2" SAE capscrew while
crankshaft is rotated.
5) Disconnect cruise control cable (if equipped). Disconnect\
wires from starter motor solenoid and disconnect CEC system harness.
Remove power brake vacuum check valve from booster (if equipped).
6) Disconnect power steering hoses from steering gear (if
equipped). Drain power steering pump reservoir and plug end of hoses.
Cap all fittings on steering gear and hoses. Raise and support
vehicle. Remove starter. Remove flywheel housing access cover.
7) Remove upper and loosen lower bellhousing-to-engine bolts.
Attach lifting equipment to engine. Raise engine off front mounts.
Place support under bellhousing. Remove remaining bellhousing-to-
engine bolts. Lift engine out of engine compartment.
4.2L
1) Remove battery and drain cooling system. Remove air
cleaner and engine compartment light from hood. Scribe hinge location
and remove hood. Disconnect and plug front fuel line at pump and fuel
return line at frame.
2) Disconnect heater hoses at heater. Label and disconnect
all wiring, lines, linkage and hoses at engine. Remove vacuum switch
assembly bracket from cylinder head cover. Remove both radiator hoses
and automatic transmission oil lines (if equipped) at radiator. Remove\
radiator and shroud.
3) Remove fan and spacer. Use 5/16" x 1/2" SAE bolt to hold
fan pulley to water pump flange. Remove starter and disconnect engine
ground strap. Remove engine mount-to-bracket nuts. Disconnect exhaust
pipe at manifold.
4) Discharge A/C system (if equipped). Disconnect and plug
hose or port openings at compressor. Disconnect hoses at power
steering gear and drain reservoir. Remove power brake vacuum check
valve. Remove bracket bolt for automatic transmission filler tube (if
equipped).
5) Lift and support vehicle. On models with automatic

SUPER CHARGERS
SWITCHES
THERMAL VACUUM VALVES
THERMOSTATIC AIR DOOR ASSEMBLIES
THERMOSTATS AND HOUSINGS
THROTTLE BODIES
THROTTLE CABLES
THROTTLE LINKAGES AND CABLES
THROTTLE POSITION SENSORS
THROTTLE POSITION SWITCHES
TIMING BELT SPROCKETS
TIMING BELTS
TORQUE STRUTS
TRANSMISSION RANGE SWITCHES
TUBE CLAMPS
TUBE CONNECTORS
TUBE COUPLERS
TUBES
TURBO CHARGERS
VACUUM CONNECTIONS
VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC)
VACUUM REGULATOR SOLENOIDS
VACUUM TUBES
VEHICLE SPEED SENSORS
VOLUME AIR FLOW SENSORS
WASTE GATE CONTROL SOLENOIDS
WASTE GATES AND BOOST CONTROL MECHANISMS
WATER PUMPS (ELECTRIC)
WATER PUMPS (NON-ELECTRIC)
WIRING HARNESSES AND CONNECTORS
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication

Reasons to Suggest Repair or Replacement
1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise,
etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience
NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present the
facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
ENGINE ASSEMBLIES
SERVICE PROCEDURES REQUIRED AND SUGGESTED FOR PROPER VEHICLE
OPERATION
CYLINDER HEAD ASSEMBLIES
NOTE: A Cylinder Head Assembly is a cylinder head fitted with
valves, associated springs, retainers, and on overhead
camshaft cylinder heads (OHC), camshaft, camshaft
bearings, lash adjusters, tappets and rockers.
CYLINDER HEAD ASSEMBLY INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Adjustable valve lash is
out of specification ... B ................. Require repair.
Internal component failure
(any component) ........ A ........... ( 1) Require repair or
replacement of cylinder
head assembly.
( 1) - It is Required that all other failure related components
be inspected for cause and condition. Additional components
or assemblies may be Suggested for repair or replacement,
such as a water pump on a short block (reason code 4,
technician's recommendation based on substantial and
informed experience).
Example:
If there is a failed head gasket with an external coolant
leak, in addition to Requiring replacement of the head
gasket, inspection of the following for cause and condition
is Required: Block, Cooling System, Cylinder Head. It may
be Suggested that additional inspections be performed, such
as the other head gasket on a V-type engine.









\









\









\









\









\









\









\


LONG BLOCK ASSEMBLIES
NOTE: A Long Block Assembly is a short block assembly together
with a cylinder head assembly and all those components
fitted within the rocker or cam cover, and timing cover

(the whole presented as an assembly). A rebuilt or new
oil pump, or kit shall be supplied or fitted as
appropriate.
LONG BLOCK ASSEMBLY INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Internal component failure
(any component) ........ A ........... (1) Require repair or
replacement of the long
block assembly.
( 1) - It is Required that all other failure related components
be inspected for cause and condition. Additional components
or assemblies may be Suggested for repair or replacement
such as a water pump on a short block (reason code 4,
technician's recommendation based on substantial and
informed experience).
Example:
If there is a failed head gasket with an external coolant
leak, in addition to Requiring replacement of the head
gasket, inspection of the following for cause and
condition is Required: Block, Cooling System, Cylinder
Head. It may be Suggested that additional inspections be
performed, such as the other head gasket on a V-type
engine.









\









\









\









\









\









\









\


SHORT BLOCK ASSEMBLIES
NOTE: A Short Block Assembly is a cylinder block and all those
components contained within the limits of the block deck
or decks, the pan rail, the block rear face and the
timing cover (where fitted), including the crankshaft.
SHORT BLOCK ASSEMBLY INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Any internal component
failure ................ A ........... ( 1) Require repair or
replacement of the short
block assembly.
( 1) - It is Required that all other failure related components
be inspected for cause and condition. Additional
components or assemblies may be Suggested for repair or
replacement, such as a water pump on a short block
(reason code 4, technician's recommendation based on
substantial and informed experience).
Example:
If there is a failed head gasket with an external coolant
leak, in addition to Requiring replacement of the head
gasket, inspection of the following for cause and condition
is Required: Block, Cooling System, Cylinder Head. It may
be Suggested that additional inspections be performed,
such as the other head gasket on a V-type engine.









\









\









\









\









\









\









\