\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Emission System Vacuum Hoses
\b\
\
\
\
\
\
\
Ignition Wires
\b\
\
\
\
\
\
\
Distributor Cap & Rotor
\b\
\
\
\
\
\
\
Battery
\
\
\
\
\
\
\
(
1) - Replacement is recommended by Chrysler at this time, but it
is not required to maintain the warranty on the PCV valve.
(
2) - Check and replace as needed.
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity