226 Body
Remove the screws retaining the speaker to
the trim panel, withdraw the speaker slightly and
disconnect the wiring connector at the rear. Place the
speaker to one side clear of the work area.
On models with a step lamp located in the
door trim panel, remove the screws, withdraw the step
lamp and disconnect the wiring connector. Using a broad bladed screwdriver, carefully
lever the trim panel outwa rds and disengage all the
retaining clips. When all the clips have been disen-
gaged maneuver the trim panel from the door. Remove the screw retaining the speaker
water deflector to the inner door panel and withdraw
the water deflector.
Carefully remove the plastic sealing sheet from
the inner door panel.
Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the plastic sealing sheet is cor-
rectly installed and not torn or damaged.
Check the trim panel retaining clips and
renew any damaged clips as necessary. On models with manual windows, wind the
door glass to the closed position, install the
retaining
clip to the regulator handle and install the regulator
handle to correspond with the regulator handle on the
opposite door.
DOOR GLASS AND REGULATOR
To Remove and Install
Remove the interior trim panel and handles
as previously described. Lower the door glass to align the lift channel
with the lower aperture. Support the door glass and remove the
retaining screws from the lift channel and door glass. Tilt the door glass to disengage it from the
run channel, then lift the door glass out through the
door glass opening. Remove the retaining bolts securing the
regulator assembly to the door panel. On models with
power windows, disconnect the wiring connector.
Maneuver the regulator assembly from the door
through the lower aperture. Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the sliding surfaces are ade-
quately lubricated with a zinc oxide grease.
Loosely install the regulator assembly to the
inner door panel. Install the doo r glass through the door glass
opening, engage the door glass in the run channel and
loosely install the retaining screws.
Tighten the regulator retaining bolts and
operate the door glass a few times up and down to
ensure that the glass is centralized. Tighten the lift
channel screws and check the operation of the door
glass. Adjust as required.
Dismantled view of the manually operated front door
window regulator and glass components.
(5) Install the plastic sealing sheet, the trim panel
and the interior handles as previously described.
REMOTE CONTROL AND DOOR LOCK
To Remove and Install
Remove the interior handles, the trim panel
and the plastic sealing sheet as previously described.
Remove the screws retaining the door lock to
the door frame. Disconnect the operating links at the door
lock from the snipper button and the lock cylinder.
The remote control link can be left connected. On
models with central locking, disconnect the link from
the lock actuator.
Remove the screws securing the remote con-
trol to the inner door panel, release the link from the
inner door panel clip and w ithdraw the remote control
and door lock assembly from the door. Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the exterior handle operates
correctly and has 0.5-2.0 mm free play at the stepped
adjuster holder. Adjust the stepped adjuster holder if
necessary. Check the operation of the door lock assem-
bly before installing the plastic sealing sheet, the trim
panel and the interior handles as previously described.
228 Body
Installed view of the front door lock striker plate.
engages the striker plate, loosen the retaining screws
and move the striker plate up or down to eliminate
the lift or drop.
Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the seal is in a serviceable
condition and correctly installed to prevent the entry
of dust and water. Tighten all the screws securely.
3. REAR DOORS
INTERIOR HANDLES AND TRIM PANEL
To Remove and Install
On models with manual windows, carefully
prise out the armrest trim plugs and remove the
retaining screws. Withdraw the armrest from the
vehicle. On models with power windows, proceed as
follows:
Carefully prise out the armrest trim plugs
and remove the retaining screws. Hold the armrest away from the door trim
panel as much as possible and lever the window
switches out from the armrest, front end first.
Lift the switches and disconnect the wiring
connector. Remove the hidden screw, working through
the switch aperture. Withdraw the armrest from the
vehicle. (3) Remove the screw retaining the remote con-
EXTERNAL MIRROR
To Remove and Install
On models with manual mirrors, remove the
screw retaining the adjuster arm handle and withdraw
the handle. Carefully prise out the cover trim plate and
remove the retaining screws securing the mirror body
to the door. On models with power mirrors, disconnect
the mirror wiring connector. Withdraw the external mirror and seal from
the door.
Rear door with the trim panel and plastic sealing sheet
removed.
SNIPPER BUTTON
REMOTE CONTROL
Dismantled view of the power door mirror.
Body 229
trol assembly escutcheon to the door and remove the
escutcheon.
(4) On models with manual windows, lever back
the regulator handle escutcheon and using a suitable
wire hook, withdraw the handle retaining clip and
remove the handle and escutcheon.
Alternatively, a piece of sturdy cloth can be used
to remove the regulator handle by sliding the cloth
behind the handle and pulling on each end of the cloth
in a see-saw action to release the retaining clip.
On models with a step lamp located in the
door trim panel, remove the screws, withdraw the
lamp and disconnect the wiring connector. Using a broad bladed screwdriver, carefully
lever the trim panel outwa rds and disengage all the
retaining clips. When all the clips have been disen-
gaged maneuver the trim panel from the door. Carefully remove the plastic sealing sheet
from the inner door panel. Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the plastic sealing sheet is cor-
rectly installed and not torn or damaged. Check the trim panel retaining clips and
renew any damaged clips as necessary. On models with manual windows, wind the
door glass to the closed position, install the
retaining
clip to the regulator handle and install the regulator
handle to correspond with the regulator handle on the
opposite door.
DOOR GLASS, REGULATOR AND QUARTER
GLASS
To Remove and Install
Remove the interior handles, the trim panel
and the plastic scaling sheet as previously described. Lower the door glass to align the lift channel
with the lower aperture.
Support the door glass and remove the
retaining screws from the lift channel.
Remove the screws retaining the rear run
channel to the door.
NOTE: To gain a ccess to the upper screw
carefully ease a small section of the door
rubber from the upper door flange.
Maneuver the run channel from the door
using care not to chip the d oor paintwork or the glass.
Withdraw the door glass through the door
glass aperture. Slide the quarter glass and seal assembly
towards the front top corner of the door and withdraw
the quarter glass from the vehicle. Remove the regulator retaining bolts and
withdraw the regulator from the door through the
lower aperture. Installation is a reversal of the removal procedure
with attention to the following points:
Dismantled view of the manually operated rear window
regulator and glass components.
Ensure that the regulator sliding surfaces are
adequately lubricated with a zinc oxide grease. Ensure that the door glass slides freely in the
run channels. The rear channe l lower bolts and the lift
channel screw are adjustable in slotted holes to
achieve this. Install the plastic sealing sheet, the trim panel
and the interior handles as previously described.
REMOTE CONTROL AND DOOR LOCK
To Remove and Install
Remove the interior handles, the trim panel
and the plastic sealing sheet as previously described. Remove the retaining screws from the re-
mote control assembly.
Remove the retaining screws from the door
lock assembly. On models with central door locking, discon-
nect the lock actuator li nk from the lock assembly by
releasing the snap clip. Withdraw the door lock assembly from the
door at the same time turning the snipper button
pivot holder to release the pivot from the door. Installation is a reversal of the removal procedure
with attention to the following points:
(1) Ensure that the exterior handle link enters
the door lock stepped adjuster when maneuvering the
door lock into position.