1987 MAZDA 626 battery

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-031
1. Accelerator cable
2. Air cleaner
3. Brake vacuum pipe
4. Intercooler pipe and hose*
5. Drive belt cover
6. Vacuum pump drive belt
7. Fuel hose
8. Water temperature switch
connector
9. Glow plug connector
10. Water thermo switch con-
nector
11. Heat gauge unit connector
12. Boost air temperature sen-
sor connector*
13. Injection pipes
14. Upper radiator hose
15. Water hose
(thermostat—FIR)
16. Oil level gauge and stay
bolt
17. Oil pipe bolt
18. Timing belt (Refer to page
1C—11)
19. Cylinder head cover
20. Camshaft pulley
21. Rear camshaft pulley
76G01C-032
22. Injection pump pulley
23. Seal plate
24. Water hose and pipe
25. Comprex supercharger
drive belt*
26. Heat insulator*
27. Exhaust manifold stay
28. Front exhaust pipe
29. Cylinder head bolt
30. Cylinder head
31. Cylinder head gasket
32. Comprex supercharger*
33. Exhaust manifold
34. Intake manifold
Note
* marked parts are equipped only for the RF-CX.
1C-16

1 C ON-VEHICLE MAINTENANCE (VALVE SEAL)
VALVE SEAL
Removal
1. Disconnect the negative battery cable.
2. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-052
76G01C-053
1. Cylinder head cover 7. Tappet and adjusting disc
2. Timing belt (Refer to page 1C—11) 8. Valve keeper
3. Camshaft pulley 9. Upper valve spring seat
4. Rear camshaft pulley 10. Valve spring
5. Camshaft cap 11. Lower valve spring seat
6. Camshaft and oil seal 12. Valve seal
1C—24

REMOVAL 1C
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-071
1. Battery and battery carrier
2. Accelerator cable
3. Air cleaner assembly
4. Radiator harness
5. Radiator hose
6. Radiator and cooling fan
7. Brake vacuum hose
8. Intercooler pipe and hose*
9. Fuel hose
10. Drive belt cover
Note
11. P/S pump
12. No.4 engine mount
13. Clutch release cylinder
14. Speedometer cable
15. Transaxle harness
16. A/C compressor
17. Engine harness
18. Heater hose
19. Front wheel
20. Engine side cover
21. Tie-rod end
22. Stabilizer control rod
23. Lower arm bushing
24. Driveshaft
25. Change rod
26. Extension bar
27. Exhaust pipe and stay
28. Engine mount
29. Engine and transaxle
30. Transaxle
marked parts are equipped only for RF-CX.
1C-31

1C INSTALLATION
Radiator
1. Install the radiator and cooling fan,
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
2. Connect the radiator harness.
76G01C-213
3. Connect the upper and lower radiator hoses.
Note
a) Position the hose clamp in the original lo-
cation on the hose.
b) Squeeze the clamp lightly with large pliers
to ensure a good fit.
4. Install the solenoid valve and ground.
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
76G01C-232
Air Cleaner Assembly
Install the air cleaner assembly.
Tightening torque:
16—27 Nm (1.6—2.8 m-kg, 12—20 ft-lb)
76G01C-233
Battery and Battery Carrier
1. Install the battery carrier.
Tightening torque:
Bolt A: 31—40
N
m
(3.2—4.1 m-kg, 23—30 ft-lb)
Bolt B: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
2. Install the battery tray and battery.
Tightening torque:
5—7 N-m (50—70 cm-kg, 43—61 in-lb)

76G01C-226

1C-98

OIL PAN 2A
OIL PAN
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G02A-009
5. Sub frame (RH)
6. Oil pan
7. Oil strainer
8. Stiffener (FE 8-valve...only ECE, 12-valve)
Removal Note
Oil pan
(DOHC)
1. Remove the oil pan mounting bolts.
2. Install the bolt ©from the mounting bolt or 10 mm
(0.39 in) bolts in the specified bolt holes ©(both
sides).
3. Screw in the bolts gradually and alternately to re-
move the oil pan.
Caution
Do not pry the oil pan to prevent damaging the
contact surface.
1. Exhaust pipe
2. Gusset plate (SOHC)
3. Clutch housing under cover (SOHC)
4. Performance plate (4WS)
2A-7

OIL PUMP 2A
OIL PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts. 76G02A-015
DOHC
76G02A-016
1. Timing belt (Refer to Section 1B) 4. Timing belt pulley
2. Oil pan (Refer to page 2A—7.) 5. Oil pump
3. Timing belt pulley lock bolt
2A-9

OIL
COOLER AND
OIL
FILTER BODY 2B

OIL
COOLER AND
OIL
FILTER BODY
REMOVAL
1. Disconnect the battery negative cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure.
76G02B-012
76G02B-013
1. Idler pulley
2. Water hose
3. Connector bolt
4. Oil cooler
5. Oil filter
6. Oil filter cover
7. Oil filter body
8. Plug
9. Pressure spring
10. Plunger control
11. Relief valve spring
12. Steel ball
INSPECTION
1. Inspect the oil cooler body for cracks or corrod-
ed. If necessary replace it.
2. Check the valves for damage or scoring if neces-
sary replace it.
3. Measure free length of each valve spring. If neces-
sary replace it.
Free length
Relief valve spring: 45.5 mm (1.79 in)
Pressure spring : 54.6 mm (2.15 in)
76G02B-014
2B-7

OIL PAN 2B
OIL PAN
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G02B-019
1. Sub frame
2. Gusset plate
3. Clutch housing
under cover
4. Water pipe
5. Oil pan
6. Oil strainer
7. Stiffener (RF-CX)
36—54 N-m (3.7-5.5 m-kg, 27—40 ft-lb)"
8—11 Nm (80—110 cm-kg 69—95 In-lb)
N-m (3.6—5.3 m-kg, 27—38 ft-lb)
(80—110 cm-kg, 69—95 in-lb)
76G02B-020
Removal Note
Oil pan
1. Remove the oil pan mounting bolts.
2. Insert a scraper or a suitable tool between the oil
pan and the stiffener to separate them.
3. Remove the oil pan.
4. Remove the oil strainer and stiffener from the
engine.
Caution
Do not bend the oil pan when prying loose.
76G02B-021
2B-9