Page 703 of 1865
4D FUEL SYSTEM
Inspection
Injection starting pressure
1. Set the nozzle on the nozzle tester.
2. Bleed the air by pumping the nozzle tester handle
several times.
3. Slowly lower the nozzle tester handle and check
the pressure when injection starts.
Injection starting pressure:
13,200 kPa (135 kg/cm2, 1,920 lb/in2) at
20°C (36°F) of fuel temperature
76G04D-073
Adjusting shim
4. If the injection starting pressure is higher than
specification, increase the shim thickness. If the in-
jection starting pressure is lower than specification,
decrease the shim thickness.
Note
Adjusting shims are availabe in 0.05 mm
(0.0197 in) thicknesses, from 1.0 mm (0.039
in) to 1.95 mm (0.077 in). When 0.05 mm
(0.0197 in) is added, injection pressure in-
creases approx. 490 kPa (5.0 kg/cm2, 70 psi).
76G04D-074
Nozzle leakage
1. Apply 11,300 kPa (115 kg/cm2,1.640 psi) pres-
sure to the injection nozzle, and check for fuel leaks
from the injection hole.
2. If fuel leaks, overhaul or replace the' injection
nozzle.
76G04D-075
Atomization (spray pattern)
1. Set the injection nozzle on the nozzle tester.
2. Bleed the air by operating the nozzle tester han-
dle several times.
3. Lower the handle several times as quickly as pos-
sible so that a pulsating whistling sound is heard,
and check the atomization.
(1) Uniform and proper atomization
(2) Incorrect injection angle and direction
4. If necessary, overhaul or replace the injection
nozzle.
76G04D-076
4D—32
Page 704 of 1865
FUEL SYSTEM 4D
76G04D-077
76G04D-078
^^^
76G04D-079
Red paint
Injection Nozzle Disassembly
Disassemble the injection nozzle.
1. Nozzle holder
2. Adjusting shim
3. Pressure spring
4. Pressure pin
5. Distance piece
6. Nozzle
7. Retaining ring
Cleaning
Clean the parts in clean test oil.
Injection Nozzle Inspection
1. Check the needle valve, nozzle body, and other
parts for damage.
2. Hold the nozzle body upright and insert approxi-
mately two thirds of the needle valve, and check
that the needle valve drops to the valve seat by
its own weight.
Injection Nozzle Assembly
1. Assemble the injection nozzle.
Tightening torque of nozzle body:
29—49 N-m (3.0—5.0 m-kg, 22—36 ft-lb)
2. Check the injection starting pressure, and atomi-
zation. (Refer to page 4D—32.)
Injection Nozzle Installation
1. Install in the reverse order of removal, referring to
the installation note.
2. Check for fuel leakage.
Installation note
Nozzle gasket
Install a new gasket with the red face toward the
nozzle.
76G04D-080
4D-33
Page 705 of 1865
4D FUEL SYSTEM
FUEL TANK
Removal and Installation
1. Drain the fuel from the fuel tank.
2. Remove in the sequence shown in the figure, referring to the removal note for the specially marked
parts.
76G04D-081
1. Fuel level gauge connector 4. Joint hose 7. Fuel tank
2. Fuel main hose 5. Ventilation hose 8. Fuel tank pad
3. Fuel return hose 6. Breather hose
Removal note
Fuel main and return hoses
1. Remove the service hole cover from the body.
2. Disconnect the fuel main and return hoses and
plug them.
Warning
Keep fire and open flame away from the fuel
area.
4D—34
Page 706 of 1865
FUEL SYSTEM 4D
Inspection
Fuel tank
Check the fuel tank for cracks or damage. Replace
if necessary.
76G04D-083
Two way check valve
1. Diconncect the hose from the fuel tank.
2. Check that the air flows in both directions through
the valve.
3. Replace the fuel vent hose if necessary.
76G04D-084
Installation
1. Install in the reverse order of removal.
2. Bleed air from fuel line.
3. Check for fuel leakage.
76G04D-085
4D-35
Page 711 of 1865
OUTLINE 5
SPECIFICATIONS
Gasoline Engine
item
Engine
F6 F8 FE
(8 VALVE)
FE (12 VALVE) FE
(DOHC)
Battery
Voltage
Type and capacity
12. Negative ground
(20 hour rate) 34B19L(S) (33 Ah): General 50D20L (50 Ah), 55D23L (60 Ah): ECE
Alternator
Type A.C.
Output V-A 12-70
Regulator type Transistorized (built-in IC regulator)
Regulated voltage 14.1-14.7
Brush length
mm (in) Standard 16.5 (0.650)
Minimum 8.0 (0.315)
Drive belt tension
mm (in)/98 N (10 kg, 22 lb) New: 6-8 (0.24-0.32), Used: 7-9 (0.28-0.35)
Starter
Type Coaxial reduction: Middle East & General (FE • carburetor)
Non-reduction: Others
Output V-kW 12-0.85
Brush length
mm (in)
12-0.95
Standard 17.0 (0.669)
Minimum 11.5 (0.453)
Unleaded fuel
17.0 (0.669)
Others
17.51
Unleaded fuel 11.5(0.453) Others 10,0 (0.394)
12-1.4 12-0.95
17.0 (0.669)
11.5 (0.453)
Ignition timing 6 ± 10 BTDC (Vacuum hose disconnected)
12
±
1° BTDC
(Test connector
grounded)
Distributor
Type Fully transistorized (HEI)
Electronic spark advance
Centrifugal spark advance
(crank angle/engine speed)
degree/rpm
F6
-2-2/1,000 6-10/2,100 14-18/6,100
F8 -2—2/1,000 10-14/2,100 18-22/6,100
FE (8 VALVE)—Carburetor Unleaded fuel
(MTX)-2—2/1,760 12—16/3,360 22—26/5,320 (ATX)-2-2/1,300 12-16/3,360 22-26/5,320
Others
-2—2/1,460 10—14/2,540 22—26/5,540
FE (12 VALVE)—Carburetor -2-2/1,200 10—14/2,400 10—14/4,000 16-20/5,000
FE—Fuel injection (except FE DOHC) -2—2/1,000 10—14/2,600 10—14/4,600 16—20/5,800
Unleaded fuel model 76G05X-503
5-5
Page 712 of 1865
5 OUTLINE
Item
Engine F6 F8 FE
(8 VALVE)
FE (12 VALVE) FE (DOHC)
F6 and F8
-2-2/100 6-10/300
FE (8 VALVE)—Carbu retor Unleaded fuel -2—2/120 8—12/245
Distributor
Vacuum spark advance (Crank angle/Vacuum)
Others (MTX) -2-(ATX) -2--2/100 16-
-2/100 10-
-20/250
-14/200
degree/mmHg (inHg) FE (12 VALVE)—Carburetor
-2-2/120 11-15/300
FE—Fuel injection (except FE DOHC) [A chamber] -2-2/125 18-22/300
[B chamber] -2-2/125 -6 10/200
Spark plug
Type
FE (8 VALVE)*1 NGK: BPR5ES-11, BPR6ES-11 Nippon Denso: W16EXR-U11, W20EXR-U11 Others
NGK: BPR5ES, BPR6ES Nippon Denso: W16EXR-U, W20EXR-U
NGK:
BCPR5E, BCPR6E Nippon
Denso: Q16PR-U, Q20PR-U
Unleaded fuel
NGK: BCPR5E-11 BCPR6E-11 BCPR7E-11
Leaded fuel NGK: BCPR5E BCPR6E
Plug gap mm (in)
0.75-0.85 (0.030-0.033), FE (8 VALVE)*1 1.0-1.1 (0.039-0.043)
0.7-0.8
(0.028-0.031)
1.0-1.1 "
/n noo
n n/9
0.7-0.8 *2 (0.028-0.031)
Firing order 1-3—4-2 76G05X-504
Diesel Engine
——Engine Item RF-N RF-CX
Battery
Voltage V 12, Negative ground Battery Type and capacity
(20 hour rate) 80D26L (65)
50D20L, 50D20R (50)-ECE 80D26L (65)
65D23L, 65D23R (55)
Alternator
Type A.C.
Alternator
Output V-A 12-70 12-75
Alternator
Regulator type Transistorized (built-in IC regulator)
Alternator Regulated voltage V 14.1-14.7 Alternator
Brush length mm (in)
Standard 16.5 (0.650) 21.5 (0.846)
Alternator
Brush length mm (in) Minimum 8.0 (0.315) 8.0 fO.315)
Alternator
Drive belt tension
mm (in)/98 N (10 kg. 92 lb) New: 9-11 (0.35-0.43), Used: 12-14 (0.47-0.55)
Starter
Type Reduction
Starter Output V—kW 12—2.0, 12-2.2 (Cold area) Starter Brush length
mm (in)
Standard 2.0 kW: 17.0 (0.669). 2.2 kW: 18.0 (0.709) Starter Brush length
mm (in) Minimum 2.0 kW: 11.0 (0.453), 2.2 kW: 11.0 (0.453)
Firing order 1-3-4-2
Unleaded fuel model *2 Leaded fuel model
76G05X-505
5-6
Page 715 of 1865
SPARK PLUG 5
Slow Charge
1. Stop the engine
2. Turn all the accessories off.
3. Remove the negative battery cable.
4. Perform a slow charge (3.5A to 4.5A).
5. Add distilled water if necessary while charging.
6. Charge once more if the specific gravity is under
fully charged gravity.
4BG05X-010
SPARK PLUG
REMOVAL AND INSTALLATION
Note the following points:
1. When the high-tension lead is to be pulled off, be
sure to pull the boot itself, and not the wire.
2. Tighten the spark plugs to the specified torque.
Tightening torque: 15—23 N-m
(1.5—2.3 m-kg, 10.8—16.6 ft-lb)
76G05X-054
Wear and adhesion or cabon
INSPECTION
Check the following points. If a problem is found, re-
place the spark plug.
1. Damaged insulation
2. Worn electrodes
3. Carbon deposits
If cleaning is necessary, use a plug cleaner or a
wire brush. Clean the upper insulator also.
4. Damaged gasket
5. Burnt condition of spark insulator
6. If it is black with carbon deposits, either misfiring
due to improper proportions of gas and air or over-
heating of the plug may have occurred.
Plug gap:
FE (12VALVE) and FE DOHC Leaded fuel
model:
0.70—0.80 mm (0.028—0.031 in)
FE (8VALVE) and FE DOHC Unleaded fuel
model:
1.0—1.10 mm (0.039—0.043 in)
Others:
0.75—0.85 mm (0.030—0.034 in)
76G05X-005
5-9
Page 745 of 1865
STARTER (GASOLINE ENGINE, 0.85, 0.95 KW TYPE) 5
76G05X-040
REMOVAL AND INSTALLATION
1. Disconnect the negative battery cable.
2. Disconnect the wiring from the starter.
3. Raise the front of the vehicle and support it with
safety stands.
4. Remove the intake manifold bracket. (Fuel Injec-
tion Engine)
5. Remove the starter bolts.
6. Draw out the starter from lower side of the vehicle.
Installation in the revers order of removal.
Tightening torque
Bolts 37—52 N m
(3.8—5.3 m-kg, 27—38 ft-lb)
B terminal 9.8—11.8 N-m
(1.0—1.2 m-kg, 87—104 in-lb)
Intake manifold bracket bolt
37—52 N-m (3.8—5.3 m-kg, 27—38 ft-lb)
Nut
19—25 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
DISASSEMBLY AND ASSEMBLY
1. Disassemble in the numbered order shown in the figure.
2. Assembly is the reverse order of disassembly. 4BG05X-049
4BG05X-075
1. Magnetic switch
2. Bolt
3. Rear cover
4. Brush-holder assembly
5. Yoke
6. Lever
7. Drive housing
(front cover)
8. Drive pinion
9. Armature
5-39
