1987 MAZDA 626 lock

ELECTRICAL SYSTEM COMPONENTS 7B
Inspection of Continuity
1. Disconnect the brake light switch connector.
2. Check for continuity between the terminals while
depressing the brake pedal.
79G07C-114
76G07B-076
KICK-DOWN SWITCH (G4A-HL)
Inspection of Terminal Voltage
1. Turn the ignition switch ON.
2. Check the voltage at terminal (V) with a voltmeter.
Depressing stroke Terminal voltage
7/8-8/8 (Full) Approx. 12V
0-7/8 Below 1,5V
3. If not correct, check the wiring harness, switch, or
adjust the switch position.
Inspection of Continuty
1. Disconnect the kick-down switch connector.
2. Check for continuity of the switch with an
ohmmeter.
Switch Continuity
Pushed Yes
Released No
3. If not correct, replace the kick-down switch.
76G07B-077
Adjustment
1. Loosen the kick-down switch locknuts.
2. Depress the accelerator pedal fully.
3. Turn the switch until the threaded case touches the
stopper.
4. Turn the switch counterclockwise by one half revo-
lution.
5. Secure the switch with the locknut.
76G07B-078
7B—67

ELECTRICAL SYSTEM COMPONENTS 7B
76G07B-083
EC-AT CONTROL UNIT (G4A-EL)
SOLENOID VALVES (G4A-EL)
Inspection of Resistance
1. Disconnect the negative battery cable.
2. Disconnect the solenoid valve connector.
3. Measure the resistance of the terminals except (A)
terminal, if necessary replace the solenoid valve.
Resistance: 13—271]
Note
1-2 solenoid valve : F
2-3 solenoid valve : C,E
3-4 solenoid valve : B
Lock-up solenoid valve : D
NO LOAD SIGNAL (G4A-EL)
Refer to STEP 3 in Troubleshooting.
MODE, AND HOLD INDICATOR LIGHT (G4A-EL)
Refer to Section 15.
OD OFF INDICATOR LIGHT (G4A-HL)
Refer to Section 15.
/ 1S 10 10 1M X 1G 1E 1C

1A
1T 1R 1P 1N 1L 1J 1H 1F 1D 1B
/—
20 2M 2K X 2E 2C 2A
2P 2N 2L 2J 2H 2F 2D 2B
Terminal Voltage Chart
Terminal Connected to Voltage Condition
1A (Input) Hold switch Approx. 12V Switch depressed 1A (Input) Hold switch Below 1.5 V Switch released
1B (Input) Mode switch (Power side) Below 1.5V POWER mode 1B (Input) Mode switch (Power side) Approx. 12V ECONOMY mode
1C (Input)
Inhibitor
switch
L range Approx. 12V L range 1C (Input)
Inhibitor
switch
L range Below 1.5V Other ranges
1D (Input) Inhibitor
switch
S range Approx. 12 V S range 1D (Input) Inhibitor
switch
S range Below 1,5V Other ranges
1E (Input)
Inhibitor
switch D range Approx. 12V D range 1E (Input)
Inhibitor
switch D range Below 1.5 V Other ranges
1F (Input)
Inhibitor
switch
N and P range
Below 1,5V N or P range 1F (Input)
Inhibitor
switch
N and P range Approx. 12V Other ranges
1G (Input) Water temperature switch Approx. 12V Above 72°C (162°F) 1G (Input) Water temperature switch Below 1,5V Below 65°C (149°F)
1H — —
11 — —
7B-69

7B ELECTRICAL SYSTEM COMPONENTS
Terminal Connected to Voltage Condition
1J — — —
1K — — —
1L (Input) Idle switch Below 1.5V At idle 1L (Input) Idle switch Approx. 12V Other speeds
1M — — —
1N (Input) Brake light switch Approx. 12V Brake pedal depressed 1N (Input) Brake light switch Below 1.5V Brake pedal released
10 (Input) Throttle sensor
Approx. 5V Ignition switch ON 10 (Input) Throttle sensor Below 1,5V Ignition switch OFF
1P (Input)
Throttle sensor
Approx. 0.5—4.3V Throttle valve fully closed to fully open
1Q (Input) Vehicle speed sensor
Approx. 4.5V During driving
1Q (Input) Vehicle speed sensor Approx. 4.5V or below 1.5V Vehicle stopped
1R (Ground) Throttle sensor Below 1,5V —
1S (Input) Pulse generator Approx. 12V Engine running 1S (Input) Pulse generator Below 1,5V Engine stopped
1S (Ground) Pluse generator Below 1.5V —
2A (Battery power) Battery Approx. 12V Ignition switch ON 2A (Battery power) Battery Below 1,5V Ignition switch OFF
2B (Ground) Body ground Below 1,5V —
2C (Memory power) Battery Approx. 12V —
2D (Ground) Body ground Below 1,5V —
2E (Output) 1-2 shift solenoid valve Approx. 12V
Refer to page 7B—26 of solenoid valve
operation table
2E (Output) 1-2 shift solenoid valve Below 1.5V Refer to page 7B—26 of solenoid valve
operation table
2F (Output) 2-3 shift solenoid valve Approx. 12V
Refer to page 7B—26 of solenoid valve
operation table
2F (Output) 2-3 shift solenoid valve Below 1,5V
Refer to page 7B—26 of solenoid valve
operation table
2G — — —
2H (Output) 3-4 shift solenoid valve Approx. 12V Refer to page 7B—26 of solenoid valve operation table 2H (Output) 3-4 shift solenoid valve Below 1.5V
Refer to page 7B—26 of solenoid valve operation table
21 — — —
2J (Output) Lock-up solenoid valve Approx. 12V Lock-up 2J (Output) Lock-up solenoid valve Below 1,5V Other
2K (Output) Hold indicator Below 1,5V Hold mode 2K (Output) Hold indicator Approx. 12V Other modes
2L (Output) Mode indicator Approx. 12V Hold mode 2L (Output) Mode indicator Below 1,5V Power or economy mode
2M (Output) EC-AT Tester
(malfunction code)
Approx. 12V Normal
2M (Output) EC-AT Tester
(malfunction code) Below 1,5V If malfunction present 2M (Output) EC-AT Tester
(malfunction code) Code signal Self-diagnosis check connector grounded
2N — — —
20 (Input) Fluid temperature switch Below 1,5V Above 150°C (302°F) 20 (Input) Fluid temperature switch Approx. 10—12V Below 143°C (289°F)
2P (Input) EC-AT check connect Approx. 12V —
76G07B-084
7B-70

7B ON-VEHICLE MAINTENANCE
86U07B-064
86U07B-065
t «
•A
0 0
0 »
LX] O 9
m
(2)

(1)

Button need not
be depressed
Button must be pressed
76F07B-022
6. Ensure that the ATF level is between the F and L
marks. Add ATF to specification, if necessary.
Low temperature scale:
20°C (68°F)
High temperature scale:
65°C (149°F)
ATF type:
Dexron II or M HI
Inspection of Condition
1. Check the ATF for discoloration.
2. Check the ATF for any unusual smell.
Note
Determine whether or not the automatic trans-
mission should be disassembled by observ-
ing the condition of fluid carefully.
If the fluid is muddy and varnished, it indicates
burned drive plates.
SELECTOR LEVER
Inspection
1. Check that the selector lever can only be shifted
as shown in the figure.
2. Make sure there is a click at each range when shift-
ed from P <-> L or P <-» 1 range.
3. Check that the position of the selector lever and
the indicator are exact.
4. Check that the button returns smoothly when used
to shift the selector.
Adjustment
1. Loosen locknuts A, B, and lockbolt C.
2. Shift the selector lever to P range.
3. Shift the transaxle to P range by moving the man-
ual shaft of the transaxle.
4. While holding the selector lever forward in P range,
tighten lockbolt C to the specified torque.
Tightening torque:
8—11 N-m (80—110 cm-kg, 67—95 in-lb)
76F07B-023
7B—72

ON-VEHICLE MAINTENANCE 7B
76F07B-024
5. Turn locknut A by hand until it just touches the
spacer.
6. Tighten locknut B to the specified torque.
Tightening torque:
8—11 N m (80—110 cm-kg, 67—96 in-lb)
7. Shift the selector lever to N range.
8. With the button on the selector lever knob pressed,
push the selector toward R range with a force of
20 N (2 kg, 4.4 lb) and check the amount of move-
ment (a) at the selector lever knob.
9. Pull the selector lever toward D range in the same
manner and check the amount of movement (b).
10. Verify the stroke difference of (a) and (b) is as
specified.
Stroke difference: 8 mm (0.315 in) max.
Note
If not with in specification, readjust locknuts
A and B.
11. Check the selector lever operation.
(Refer to Inspection section.)
76F07B-025
THROTTLE CABLE
Inspection
1. Check the inner and outer cable for damage.
2. Make sure that the accelerator operates smoothly.
86U07B-066
Removal
1. Remove the battery and battery carrier.
2. Disconnect the main fuse block. (G4A-EL)
76G07B-090
7B—73

ON-VEHICLE MAINTENANCE 7B
'mfm^i! kfOl iff t—
76G07B-093
76G07B-094
Main fuse block (G4A-EL)
Install the main fuse block.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
Battery carrier
Install the battery carrier.
Tightening torque:
31—40 Nm (3.2—4.1 m-kg, 23—30 ft-lb)
ATF level
After installation, add ATF, and with the engine idling,
check the fluid level and for leaks. (Refer to page
7 B—71)
Adjustment (G4A-EL)
1. Remove the splash shield next to the left front tire.
2. Remove the square head plug L and install the
SST
3. Shift into P range and start the engine. Warm up
the engine to normal operating temperature, and
adjust the idle speed.
Idle speed: 950 ±5o rpm
76G07B-095
3 CO CO 03

(1)

L
Line pressure
beeing to increase
I
Adjusting point

•
clockwise Counter
clockwise Position of locknuts
86U07B-482
4. Adjust locknuts as follows:
When the locknuts are moved, line pressure is in-
creased or decreased as shown. Adjust the lock-
nuts to the correct position using the following
procedure.
(1) Initially install the locknuts fully away from the
throttle cam. (Loosen the cable all the way)
(2) Adjust the locknuts in a clockwise direction as
viewed from the front of the vehicle until the
line pressure begins to increase above the
specification shown below.
7B—75

7B ON-VEHICLE MAINTENANCE
Line pressure decreases
Line pressure increases
86U07B-483
Protector
-7 / Throttle cable
86U07B-080
(3) Adjust the locknuts in a counterclockwise direc-
tion until the line pressure decreases to the
specification. Tighten the locknuts.
Specified pressure: 432—450 kPa
(4.4—4.6 kg/cm2, 63—66 psi)
Note
Transmission in P range
5. Turn off the engine.
6. Reinstall the square head plug.
Tightening torque:
5—10 N m (50—100 cm-kg, 43—87 in-lb)
7. Fully open the throttle valve; then crimp the pin with
the protector installed as shown.
8. Remove the protector.
Adjustment (G4A-HL)
1. Remove the splash shield next to the left front tire.
2. Remove the square head plug T and install the
SST
3. Shift into P range and start the engine. Warm up
the engine to normal operating temperature, and
adjust the idle speed.
Idle speed: 900 -5o rpm
76G07B-096
3 tn tn (1)
L
Counter- ^ clockwise
Throttle pressure
beeing to increase
I Adjusting point
Position of locknuts
Clockwise
4. Adjust locknuts as follows:
When the locknuts are moved, throttle pressure is
increased or decreased as shown. Adjust the lock-
nuts to the correct position using the following
procedure.
(1) Initially install the locknuts fully away from the
throttle cam. (Loosen the cable all the way)
(2) Adjust the locknuts in a clockwise direction as
viewed from the front of the vehicle until the
throttle pressure begins to increase above the
specification shown below.
76G07B-097
7B—76

ON-VEHICLE MAINTENANCE 7B
Line pressure decreases
Line pressure increases
76G07B-098
Protector
NAAA/V^
/NA/w^nJ
Throttle cable Crimp
86U07B-080
(3) Adjust the locknuts in a counterclockwise direc-
tion until the throttle pressure decreases to the
specification. Tighten the locknuts.
Specified pressure: 88—108 kPa
(0.9—1.1 kg/cm2, 13—16 psi)
Note
Transmission in P range
5. Turn off the engine.
6. Reinstall the square head plug.
Tightening torque:
5—10 N m (50—100 cm-kg, 43—87 in-lb)
7. Fully open the throttle valve; then crimp the pin with
the protector installed as shown.
8. Remove the protector.
CONTROL VALVE BODY
Note
Remove the control valve body only if
troubleshooting indicates a probable failure.
Removal
1. Remove the throttle cable. (Refer to 7B—73)
2. Disconnect the solenoid connector.
76G07B-099
3. Remove the control valve body.
Disassembly, Inspection and Assembly
Refer to control valve body section of INSPECTION
AND REPAIR.
86U07B-082
7B—77