1987 MAZDA 626 door lock

LOCATION OF UNIT, RELAY AND SWITCH 1 5
LOCATION OF
UNIT,
RELAY AND SWITCH
STRUCTURAL VIEW
Door SW
Power window SW
AAS control unit
Cruise control unit
Relay box
(EGI and Diesel model)
Engine control unit
Brake fluid level sensor
Main fuse block
(EGI model)
Main fuse block
(Carburetor model) | \ Relay box
Main fuse block Relay box
(Diesel model) (Carburetor model)
Power window SW
Door SW
Door lock SW
AAS control SW
CPU and joint box
86U15X-002
15-7

JOINT
BOX AND FUSE
1
5
JOINT BOX AND FUSE
STRUCTURAL VIEW
Joint box Circuit breaker
(Rear window
defroster)
Reset button
Fuses
West Germany
(REAR FOG* RADIO 15A 15A (HEADCLEANER) 20A
(POWER 30A WIND) TAIL (LH) 15A STOP 15A
TAIL (RH) 15A METER 15A TURN 15A
ROOM 15A f(D00R LOCK) [ 30A c
HORN 5A
(AIR COND)' 15A (COOLING 20A FAN>I ENGINE 15A
(REAR 15A WIPER) WIPER 20A (SUN ROOF) [ 15A
ECE, LHD and RHD General (Diesel model)
. Q .
(REAR FOG) 15A J RADIO 15A (rHEADCLEAMEfii I joa J (POWER 1 30A WIND)j (DIM DIP) 15A ( HAZAARD ' I TAIL 15A METER 15A TURN 15A
' ROOM ' ISA j flBOOR LOCKl"1 L STOP 1SA -[(AIR COND) 15A J ' ENGINE 15A
(REAR 15A WIPER) WIPER 20A (SUN ROOF) I 16A
RHD General
only
UK, RHD General
(REAR FOG)
[
15A J
RADIO 15A (HEADCLEANER) 20A
(POWER 30A WIND) (DIM DIP) 15A HAZARD 10A
TAIL 15A METER 10A TURN 15A
ROOM 15A (DOOR LOCK) 30A STOP 15A
(AIR COND) 15A '(COOLING 20A FAN) ENGINE 15A
(REAR 15A WIPER) WIPER 20A (SUN ROOF) [ 15A ,
ECE, Middle East, LHD General
Q
(REAR FOG) 15A J RADIO 15A (HEADCLEANER) 20A
(POWER 30A WIND) HAZARD 10A
TAIL 15A METER 15A TURN 15A
ROOM 5A (DOOR LOCK) 3CA STOP tSA ] (AIR CONO)| . ISA jj| ((COOLING! ( ENGINE 1 J [
BOA
FAfJ)J [ 15A J
(REAR 15AWIP£R), ^ C WIPER "1[SUN HOOF?
1)J
[ 2QA
J
[ 15A
West Germany (Diesel model)

MAIN (fWl
ISA I
MALM (LM1
15A
DIM iLHI
ISA
PEAfl FOCii
I 'SA | RAQIO T5A I
HEAP CLEANEF*
1 I (POWEfl I
3PA WI^D;. TAIL (LH)
15A
)C
TAIL I ISA METER 1OA TURN 15A FIOQM
(DOOR LOC*C|
HOflN 15A Jt 1SA

(
AIR COND)
jy (COOUNQ
gqA FAN)
ENGINE 16A

|fl£AR WlPEFl!
ILJSi '
DEfOO
3 OA
Dtf
WtPEfl
USUNROQF Jl JPA H 15A [
86U15X-006
15-11

CENTRAL PROCESSING UNIT (CPU) 1 5
REMOVAL AND INSTALLATION
1. Disconnect the negative battery cable.
2. Disconnect the CPU connectors.
3. Release the lock and remove the CPU from the
joint box.
4. Install in the reverse order of removal.
ON-VEHICLE INSPECTION
Note: Check the voltage between "a through
I" terminal and ground.
Check the continuity between "m,
n" terminal and ground.
86U15X-075

Terminal Connecting
to
Measurement condition Measurement value
a Interior light and courtesy lights Any time Approx.
12V

b Batterv Anv time Approx.
12V

c No used
— —

d Ground Anv time OV
e Seat belt warning light Ignition switch
ON
Approx.
12V

f Enaine control unit Enaine runnina Approx.
12V

g Key cylinder illumination light Any time Approx.
12V

i Key reminder switch Insert the key into the cylinder
Pull out the key from the cylinder
Approx.
12V

OV
j Ignition switch (ON) Ignition switch
ON

Ignition switch OFF
or
ACC
Approx.
12V

OV
k Ignition switch (ACC) Ignition switch
ON or
ACC
Ignition switch OFF
Approx.
12V

OV
I Light switch (In the combination switch) Turn the light switch ACC and
ON

Light switch OFF
Approx.
12V

OV
m Seat belt switch Seat belt fastened
Seat belt unfastered

OQ

OO
n Door switch Door closed
Door open
OO
on

76G15X-009
15—43

15 POWER WINDOW

OK Check power window switch
on
each door. Refer
to
page 15—67.

76G15X-059
INSPECTION
Power Window Driver's Side Switch
(For Sedan and Hatchback)
Check for continuity between terminals of the switch.
Main switch

—Terminal Position -——___ h i
Lock
Unlock
O o
O O:
Indicates continuity

76G15X-016
c f i i 0
b e h k n
a d R J m /
O O:
Indicates continuity

15-66

POWER DOOR LOCK 1 5
POWER DOOR LOCK
STRUCTURAL VIEW
CIRCUIT DIAGRAM

BATTERY

86U15X-171
15—105

1 5 POWER DOOR LOCK
TROUBLESHOOTING

Terminal Voltage
WG 12V
B OV
Check the voltage
at GB
terminal
of
the power door lock relay with each switch condition.
Terminal Condition Voltage
GB Lock 12V GB Unlock OV

OK

Check the voltage
at R
and
G
terminal
of
the power door lock relay with each switch condition.
Terminal Condition Voltaae
R Lock OV R Unlock 12V
G Lock 12V G Unlock OV

Power door lock does not operate.

Check DOOR LOCK 30A fuse.

OK
NG
Short circuit.
Check the voltage
at
each terminal
of
the power door lock relay connector.

NG
Repair the harness. (Fuse box
to
relay, Relay
to
ground)

OK

Check the power door lock switch. Refer
to
page 15-107.

OK
NG
Replace the switch.

NG
Repair the harness. (Door lock switch
to
relay)

NG
Replace the door lock relay.

OK

Check the power door lock motor. Refer
to
page
15-107.

OK

Repair the harness. (Relay
to
each motors)

NG
Replace the door lock motor.

76G15X086
15—106

POWER DOOR LOCK 1 5
86U15X-173
INSPECTION
Power Door Lock Switch
1. Check for continuity of the switch with an
ohmmeter.

WG GB B
Lock
o O

Unlock
o O

O
O:
indicates continuity

2. If continuity is not as specified, replace the switch.
Power Door Lock Motor
1. Check operation of the door lock actuator when
the battery voltage is applied to the terminal.

Connecting
to
Door lock motor 12V ground Door lock motor
G R LOCK (Pull)
R G UNLOCK (Release)

2. If not, replace the door lock motor.
86U15X-174
15—107