Page 355 of 3115
I25814
Wire Harness Side
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-103
2476 Author: Date:
2004 LAND CRUISER (RM1071U)
High voltage might be shown 1 to 2 times after leaving the
battery, judge should be made with the voltage shown at
the 3rd time or later.
(g) Disconnect the lead.
(h) Set the battery (lithium battery) in the transmitter.
(i) Install the cover, so that the O-ring is not distorted or
slipped off.
(j) Using a screwdriver, tighten the 2 screws.
6. INSPECT WIRELESS DOOR LOCK CONTROL TUNER
CIRCUIT
Disconnect the connector from the tuner and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 (E) - GroundConstantContinuity
2 (RDA) - GroundIgnition switch OFF, without key, all doors
closed,, and transmitter switch OFF " ONBelow 1 V e 6 V
5 (+B) - Ground-Repeatedly chage 0 - 5V
If the circuit is not as specified, inspect the circuit connected to
other parts.
Page 356 of 3115
BE0CH-09
I25815
Transmitter:Door Key Lock and
Unlock Switch Front Door Lock Assembly
Front Door Lock Motor
Front Door Unlock Detection SwitchRear Door Lock Assembly
Rear Door Lock Motor
Rear Door Unlock Detection Switch
Front Door Lock Assembly
Front Door Lock Motor
Front Door Unlock
Detection Switch
Rear Door Lock Assembly
Rear Door Lock Motor
Rear Door Unlock
Detection Switch
Ignition Switch
Wireless Door Lock ECU
BE-98
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2471 Author: Date:
2004 LAND CRUISER (RM1071U)
LOCATION
Page 359 of 3115
START
The vehicle should be in the following conditions:
Ignition switch ON
Hand-held tester operation:
1. Select ºL/C 100º from the menu.
2. Select ºTDSº (Theft Deterrent System).
3. Select ºWIRELESS REGISTRATIONº.
After the above operations, proceed to the succeeding operations
according to the prompts on the tester screen.
Transmitter SW Operation:
HINT: Perform this operation during the countdown screen.
Press both lock and unlock SW. (Between 1 and 1.5 sec.)
Press any one of SW. (For more than 1 sec.)
This wireless buzzer sounds when the registration is completed
normally.
Continue the registration.Register other transmitters?
Or
Finish the registration?
Finish the registration.
ENDHINT: Select the next step
on the tester screen.
Within 3 sec. BE-94
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2467 Author: Date:
2004 LAND CRUISER (RM1071U)
(c) By TOYOTA Hand-Held Tester
HINT:
This page is to show briefly the registration procedure using the hand-held tester.
For detailed procedures, please refer to the prompts on the tester screen.
The number of currently registered codes can be checked out on the first screen of the WIRELESS REG-
ISTRATION.
Page 360 of 3115
Close"open"close"open
START
The vehicle should be in the following conditions:
Driver door open (Other doors are closed).
Insert and remove the key into/from the ignition cylinder twice.
Insert"remove "insert"remove
HINT: If the IG switch operation is
not performed with the specified
number of times (If it is 4 times, 6
times or more), this operation is
finished with no response.
HINT: The registration operation is
cancelled if each operation is not
completed within the specified
time.
No key inserted in the IG key cylinder.
Close and open the driver door twice.
Close"open"close"open
Insert and remove the key into/from the ignition cylinder once.
Insert"remove
Insert the key into the ignition key cylinder.
Close all the doors.
Mode Selection
Turn the IG SW ON
u"LOCK once.Add modeTurn the IG SW ON
u"LOCK twice.Rewrite modeTurn the IG SW ON
u"LOCK 3 times. Confirmation modeTurn the IG SW ON
u"LOCK 5 times. Prohibition mode
Remove the key from the IG key cylinder.
Within 5 sec.
Within 40 sec.
Within 40 sec.
Within 40 sec.
Close and open the driver door twice.
- BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE-95
2468 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) By Switch Operation:
Page 422 of 3115
BO4IX-01
H20976
H20977
H20975
: 8 Clips
H20978
BO-84
- BODYINSTRUMENT PANEL
2658 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. w/ CD Changer Built In The Audio System:
SHIP MODE SETTING
(a) Take out all of the CDs.
NOTICE:
If they cannot be taken out, do not attempt to take out forci-
bly and send the unit for repair.
(b) Turn the ignition switch to ACC as pressing the ºSEEK
UPº and ºDISCº switches at the same time.
HINT:
When the ship mode has been set, ºSHIPº must be displayed.
(c) Turn the ignition switch to OFF and disconnect the battery
negative cable.
NOTICE:
Connecting the battery negative cable automatically end
the ship mode.
2. REMOVE CENTER REGISTER
(a) Using a moulding remover, remove the center register.
(b) Disconnect the connector.
(c) Use the same manner described above to the other side.
3. REMOVE RADIO WITH A/C CONTROL ASSEMBLY
(a) Remove the 4 bolts.
(b) Disconnect the radio with A/C control assembly cable and
remove the radio with A/C control assembly.
4. w/ CD Changer Built In The Audio System:
SHIP MODE CONFIRMATION
Check that a metal can be seen from holes marked ºSHIPº on
the back of the radio with A/C control assembly.
NOTICE:
If a metal cannot be seen from a hole on the back of the ra-
dio with A/C control assembly, repeat ºSHIP MODEº.
5. REMOVE FRONT DOOR SCUFF PLATES
6. REMOVE COWL SIDE TRIMS
7. REMOVE FRONT DOOR OPENING TRIMS
Page 484 of 3115
BO21G-03
H05264
Claw
H05265
: 4 Clips
- BODYSEAT BELT PRETENSIONER
BO-141
2715 Author: Date:
2004 LAND CRUISER (RM1071U)
SEAT BELT PRETENSIONER
REMOVAL
NOTICE:
If the wiring connector of the seat belt pretensioner
is disconnected with the ignition switch at ON or ACC,
diagnostic trouble codes will be recorded.
Never use seat belt pretensioner from another ve-
hicle. When replacing seat belt pretensioner, replace
it with a new one.
1. REMOVE FRONT DOOR SCUFF PLATE
2. REMOVE FRONT DOOR OPENING TRIM
3. REMOVE REAR DOOR SCUFF PLATE
4. REMOVE REAR DOOR OPENING TRIM
5. REMOVE CENTER PILLAR LOWER GARNISH
(a) Using a screwdriver, remove the center pillar garnish cov-
er.
HINT:
Tape the screwdriver tip before use.
(b) Using a screwdriver, remove the center pillar lower gar-
nish as shown in the illustration.
HINT:
Tape the screwdriver tip before use.
6. REMOVE FRONT SEAT OUTER BELT SHOULDER AN-
CHOR
7. REMOVE FRONT SEAT OUTER BELT FLOOR AN-
CHOR
8. REMOVE RETRACTOR OF FRONT SEAT OUTER
BELT
CAUTION:
Never disassemble the retractor of front seat outer belt.
NOTICE:
When removing the retractor of front seat outer belt, take
care not to pull the seat belt pretensioner wire harness.
Page 485 of 3115
H04094
A
B BO-142
- BODYSEAT BELT PRETENSIONER
2716 Author: Date:
2004 LAND CRUISER (RM1071U)
(a) Disconnect the pretensioner connector in the order ºAº
and ºBº as shown in the illustration.
CAUTION:
When removing the seat belt pretensioner, work must be
started 90 seconds after the ignition switch is turned to the
ºLOCKº position and the negative (-) terminal cable is dis-
connected from the battery.
(b) Remove the bolt and retractor of front seat outer belt.
Page 519 of 3115
BR12E-07
F06425
TOYOTA
Hand-held
Tester
DLC3
BR-4
- BRAKEBRAKE FLUID
2140 Author: Date:
2004 LAND CRUISER (RM1071U)
BRAKE FLUID
BLEEDING
HINT:
If any work is done on the brake system or if air in the
brake lines is suspected, bleed the air from the system.
When bleeding, keep the amount of the fluid within the
line of reservoir between Min. and Max.
NOTICE:
Do not let brake fluid remain on painted surfaces.
Wash it off immediately.
With the reservoir cap removed, when depressing the
brake pedal, the fluid will spray.
1. FILL RESERVOIR WITH BRAKE FLUID
Fluid: SAE J1703 or FMVSS NO. 116 DOT3
2. In case of using TOYOTA hand-held tester:
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-
nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.
(a) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Turn the ignition switch ON, check that the pump stops af-
ter approx. 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (a) and (b) again.
(c) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(d) Observe the procedure in step 4 and bleed the right and
left front brake caliper.
(e) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.
(f) Connect TOYOTA hand-held tester.
(1) Turn the ignition switch OFF, connect the TOYOTA
hand-held tester to DLC3.
(2) Turn the ignition switch ON and select ºAIR BLEED-
INGº on the TOYOTA hand-held tester.
HINT:
Please refer to the TOYOTA hand-held tester operator's manu-
al for further details.
