1986 TOYOTA LAND CRUISER ignition

AB0119H10600H01065H01066
H01007
H21140
Airbag
Sensor
Assembly
CG
TCON
" u
DTC B1141/33 " u
DLC3
Side and Curtain
Shield Airbag
Sensor Assembly RH
DTC B1140/32
DI-818
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1011 Author
: Date
:
2004 LAND CRUISER (RM1071U)
8 Check airbag sensor assembly.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the connector to the airbag sensor assembly.
(d) Change the side and curtain shield airbag sensor assem-
bly RH position with LH position.
(e) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
Neither DTC B1141/33 nor B1140/32 are not output.
HINT:
Codes other than code B1141/33 or B1140/32 may be output
at this time, but they are not relevant to this check.
NG Replace airbag sensor assembly
(DTC B1141/33 is output).
NG Replace side and curtain shield airbag sensor
assembly LH (DTC B1140/32 is output).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

AB0119H10600H16830H17106
ON
CG
TCDTC B1148/36
DLC3
DI-820
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1013 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Is DTC B1148/36 output?
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B1148/36 is output.
HINT:
Codes other than code B1148/36 may be output at this time, but
they are not relevant to this check.
NO The malfunctioning part can now be considered
normal. To make sure of this, use the simulation
method to check.
YES
2 Is connector of front airbag sensor RH properly connected?
No Connect connector.
YES
3 Prepare for inspection (See step 1 on DI-923).

H03363AB0119H21557H21720
Airbag
Sensor
Assembly
Airbag Sensor Assembly
(+)
-SR+SR
(-)ONFront
Airbag
Sensor
RH
DI-822
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1015 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6 Check wire harness (to B+).
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and each
of +SR and -SR on the airbag sensor assembly side be-
tween the front airbag sensor RH and the airbag sensor
assembly.
OK:
Voltage: Below 1 V
NG Go to step 12.
OK

AB0119H10600H16834H16835H21556H21721
Airbag
Sensor
Assembly
ON
DTC B1148/36"u "u
DLC3
TC CG
DTC B1149/37
Front
Airbag
Sensor
LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-823
1016 Author
: Date
:
2004 LAND CRUISER (RM1071U)
7 Check airbag sensor assembly.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the connector to the airbag sensor assembly.
(d) Change the front airbag sensor LH position with RH posi-
tion.
(e) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
Neither DTC B1148/36 nor B1149/37 are not output.
HINT:
Codes other than code B1148/36 or B1149/37 may be output
at this time, but they are not relevant to this check.
NG Replace airbag sensor assembly
(DTC B1148/36 is output).
NG Replace front airbag sensor RH
(DTC B1149/37 is output).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

H21553AB0119H03364H21726
Engine Room
Main Wire
Front
Airbag
Sensor
RHAirbag
Sensor
Assembly u"
(+) (-)+SR
-SR
ON
DI-826
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1019 Author
: Date
:
2004 LAND CRUISER (RM1071U)
12 Check engine room main wire (to B+).
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Disconnect the engine room main wire connector on the
airbag sensor assembly side.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and each
of +SR and -SR of the engine room main wire connector
on the airbag sensor assembly side.
OK:
Voltage: Below 1 V
NG Repair or replace engine room main wire.
OK

H21552AB0119H16253H21727
Front
Airbag
Sensor
RHAirbag
Sensor
Assembly u"
(+) (-)+SR
-SR
Engine Room
No. 2 WireDash Wire
ON
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-827
1020 Author
: Date
:
2004 LAND CRUISER (RM1071U)
13 Check engine room No. 2 wire (to B+).
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Disconnect the engine room No. 2 wire connector from
the dash wire.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and each
of +SR and -SR of the engine room No. 2 wire connector
on the dash wire side.
OK:
Voltage: Below 1 V
NG Repair or replace engine room No. 2 wire.
OK
Repair or replace dash wire.

AB0119H10600H16831H17109
ON
CG
TCDTC B1149/37
DLC3
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-829
1022 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Is DTC B1149/37 output?
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B1149/37 is output.
HINT:
Codes other than code B1149/37 may be output at this time, but
they are not relevant to this check.
NO The malfunctioning part can now be considered
normal. To make sure of this, use the simulation
method to check.
YES
2 Is connector of front airbag sensor LH properly connected?
NO Connect connector.
YES
3 Prepare for inspection (See step 1 on page DI-923).

AB0119H21557H08065H21730
Airbag
Sensor
Assembly
(+)+SL
(-)
-SL Airbag Sensor
Assembly
ONFront
Airbag
Sensor
LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-831
1024 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6 Check wire harness (to B+).
PREPARATION:
Connect the negative (-) terminal cable to the battery, and wait
at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and each
of +SL and -SL on the airbag sensor assembly side be-
tween the front airbag sensor LH and the airbag sensor
assembly.
OK:
Voltage: Below 1 V
NG Go to step 12.
OK